Fix translation of peripheral register addresses

This was already incorrect in the original ESP32 implementation
but was discovered while testing the new S2/S3 implementation.

This was also wrong within the ESP-IDF, that we based the translation
logic on. Espressif fixed the issue in this pull request:
espressif/esp-idf#11652

We now also have unit tests and compat (integration) tests, that
compare our binary output against that of binutils-gdb/esp32-ulp-as,
which already did this translation correctly, but we didnt have a
test for the specific cases we handled incorrectly, so we didn't
notice this bug.

This fix has also been tested on a real device, because S2/S3 devices
need the IOMUX clock enabled in order to be able to read GPIO input
from the ULP, and enabling that clock required writing to a register
in the SENS address range, which didnt work correctly before this fix.

esp32_ulp/opcodes.py

@@ -379,7 +379,7 @@ def i_reg_wr(reg, high_bit, low_bit, val):
         _wr_reg.addr = reg & 0xff
         _wr_reg.periph_sel = (reg & 0x300) >> 8
     else:
-        _wr_reg.addr = (reg & 0xff) >> 2
+        _wr_reg.addr = (reg >> 2) & 0xff
         _wr_reg.periph_sel = _soc_reg_to_ulp_periph_sel(reg)
     _wr_reg.data = get_imm(val)
     _wr_reg.low = get_imm(low_bit)
@@ -394,7 +394,7 @@ def i_reg_rd(reg, high_bit, low_bit):
         _rd_reg.addr = reg & 0xff
         _rd_reg.periph_sel = (reg & 0x300) >> 8
     else:
-        _rd_reg.addr = (reg & 0xff) >> 2
+        _rd_reg.addr = (reg >> 2) & 0xff
         _rd_reg.periph_sel = _soc_reg_to_ulp_periph_sel(reg)
     _rd_reg.unused = 0
     _rd_reg.low = get_imm(low_bit)

esp32_ulp/opcodes_s2.py

@@ -422,7 +422,7 @@ def i_reg_wr(reg, high_bit, low_bit, val):
         _wr_reg.addr = reg & 0xff
         _wr_reg.periph_sel = (reg & 0x300) >> 8
     else:
-        _wr_reg.addr = (reg & 0xff) >> 2
+        _wr_reg.addr = (reg >> 2) & 0xff
         _wr_reg.periph_sel = _soc_reg_to_ulp_periph_sel(reg)
     _wr_reg.data = get_imm(val)
     _wr_reg.low = get_imm(low_bit)
@@ -437,7 +437,7 @@ def i_reg_rd(reg, high_bit, low_bit):
         _rd_reg.addr = reg & 0xff
         _rd_reg.periph_sel = (reg & 0x300) >> 8
     else:
-        _rd_reg.addr = (reg & 0xff) >> 2
+        _rd_reg.addr = (reg >> 2) & 0xff
         _rd_reg.periph_sel = _soc_reg_to_ulp_periph_sel(reg)
     _rd_reg.unused = 0
     _rd_reg.low = get_imm(low_bit)

tests/01_compat_tests.sh

@@ -10,6 +10,19 @@ calc_file_hash() {
     shasum < $1 | cut -d' ' -f1
 }
 
+make_log_dir() {
+   mkdir -p log
+}
+
+fetch_esp_idf() {
+    [ -d esp-idf ] && return
+
+    echo "Fetching esp-idf"
+    log_file=log/fetch-esp-idf.log
+    git clone --depth 1 \
+        https://github.com/espressif/esp-idf.git 1>$log_file 2>&1
+}
+
 run_tests_for_cpu() {
     local cpu=$1
     echo "Testing for CPU: $cpu"
@@ -33,7 +46,10 @@ run_tests_for_cpu() {
         bin_file="${src_name}.bin"
 
         echo -e "\tBuilding using binutils ($cpu)"
-        gcc -E -o ${pre_file} $src_file
+        echo "INCLUDING: esp-idf/components/soc/$cpu/include"
+        gcc -I esp-idf/components/soc/$cpu/include -I esp-idf/components/esp_common/include \
+            -x assembler-with-cpp \
+            -E -o ${pre_file} $src_file
         esp32ulp-elf-as --mcpu=$cpu -o $obj_file ${pre_file}
         esp32ulp-elf-ld -T esp32.ulp.ld -o $elf_file $obj_file
         esp32ulp-elf-objcopy -O binary $elf_file $bin_file
@@ -56,5 +72,7 @@ run_tests_for_cpu() {
     echo ""
 }
 
+make_log_dir
+fetch_esp_idf
 run_tests_for_cpu esp32
 run_tests_for_cpu esp32s2

tests/compat/reg.esp32.S

@@ -0,0 +1,15 @@
+#include "soc/rtc_cntl_reg.h"
+#include "soc/soc_ulp.h"
+
+  reg_rd 0x012, 1, 2
+  reg_rd 0x234, 3, 4
+  reg_rd 0x345, 5, 6
+
+  reg_wr 0x012, 1, 2, 1
+  reg_wr 0x234, 3, 4, 1
+  reg_wr 0x345, 5, 6, 1
+
+  WRITE_RTC_REG(0x3ff484a8, 1, 2, 3)
+  READ_RTC_REG(0x3ff484a8, 1, 2)
+  WRITE_RTC_REG(0x3ff48904, 1, 2, 3)
+  READ_RTC_REG(0x3ff48904, 1, 2)

tests/compat/reg.esp32s2.S

@@ -0,0 +1,15 @@
+#include "soc/rtc_cntl_reg.h"
+#include "soc/soc_ulp.h"
+
+  reg_rd 0x012, 1, 2
+  reg_rd 0x234, 3, 4
+  reg_rd 0x345, 5, 6
+
+  reg_wr 0x012, 1, 2, 1
+  reg_wr 0x234, 3, 4, 1
+  reg_wr 0x345, 5, 6, 1
+
+  WRITE_RTC_REG(0x3f4084a8, 1, 2, 3)
+  READ_RTC_REG(0x3f4084a8, 1, 2)
+  WRITE_RTC_REG(0x3f408904, 1, 2, 3)
+  READ_RTC_REG(0x3f408904, 1, 2)

tests/opcodes.py

@@ -174,6 +174,31 @@ def test_reg_address_translations():
     assert ins.addr == 0x2a  # low 8 bits of 0x12a
 
 
+def test_reg_address_translations_sens():
+    """
+    Test addressing of peripheral registers using full DPORT bus addresses
+    """
+
+    ins = make_ins("""
+    addr : 8        # Address within either RTC_CNTL, RTC_IO, or SARADC
+    periph_sel : 2  # Select peripheral: RTC_CNTL (0), RTC_IO(1), SARADC(2)
+    unused : 8      # Unused
+    low : 5         # Low bit
+    high : 5        # High bit
+    opcode : 4      # Opcode (OPCODE_RD_REG)
+    """)
+
+    # direct ULP address is derived from full address as follows:
+    # full:0x3ff48904 == ulp:(0x3ff48904-DR_REG_RTCCNTL_BASE) / 4
+    # full:0x3ff48904 == ulp:(0x3ff48904-0x3f408000) / 4
+    # full:0x3ff48904 == ulp:0x904 / 4
+    # full:0x3ff48904 == ulp:0x241
+    # see: https://github.com/espressif/binutils-esp32ulp/blob/249ec34/gas/config/tc-esp32ulp_esp32s2.c#L78
+    ins.all = opcodes.i_reg_rd("0x3ff48904", "0", "0")
+    assert ins.periph_sel == 2  # high 2 bits of 0x241
+    assert ins.addr == 0x41  # low 8 bits of 0x241
+
+
 test_make_ins_struct_def()
 test_make_ins()
 test_arg_qualify()
@@ -183,3 +208,4 @@ def test_reg_address_translations():
 test_eval_arg()
 test_reg_direct_ulp_addressing()
 test_reg_address_translations()
+test_reg_address_translations_sens()

tests/opcodes_s2.py

@@ -174,6 +174,31 @@ def test_reg_address_translations_s2():
     assert ins.addr == 0x2a  # low 8 bits of 0x12a
 
 
+def test_reg_address_translations_s2_sens():
+    """
+    Test addressing of ESP32-S2 peripheral registers using full DPORT bus addresses
+    """
+
+    ins = make_ins("""
+    addr : 8        # Address within either RTC_CNTL, RTC_IO, or SARADC
+    periph_sel : 2  # Select peripheral: RTC_CNTL (0), RTC_IO(1), SARADC(2)
+    unused : 8      # Unused
+    low : 5         # Low bit
+    high : 5        # High bit
+    opcode : 4      # Opcode (OPCODE_RD_REG)
+    """)
+
+    # direct ULP address is derived from full address as follows:
+    # full:0x3f408904 == ulp:(0x3f408904-DR_REG_RTCCNTL_BASE) / 4
+    # full:0x3f408904 == ulp:(0x3f408904-0x3f408000) / 4
+    # full:0x3f408904 == ulp:0x904 / 4
+    # full:0x3f408904 == ulp:0x241
+    # see: https://github.com/espressif/binutils-esp32ulp/blob/249ec34/gas/config/tc-esp32ulp_esp32s2.c#L78
+    ins.all = opcodes.i_reg_rd("0x3f408904", "0", "0")
+    assert ins.periph_sel == 2  # high 2 bits of 0x241
+    assert ins.addr == 0x41  # low 8 bits of 0x241
+
+
 def test_reg_address_translations_s3():
     """
     Test addressing of ESP32-S3 peripheral registers using full DPORT bus addresses
@@ -199,6 +224,31 @@ def test_reg_address_translations_s3():
     assert ins.addr == 0x2a  # low 8 bits of 0x12a
 
 
+def test_reg_address_translations_s3_sens():
+    """
+    Test addressing of ESP32-S3 peripheral registers using full DPORT bus addresses
+    """
+
+    ins = make_ins("""
+    addr : 8        # Address within either RTC_CNTL, RTC_IO, or SARADC
+    periph_sel : 2  # Select peripheral: RTC_CNTL (0), RTC_IO(1), SARADC(2)
+    unused : 8      # Unused
+    low : 5         # Low bit
+    high : 5        # High bit
+    opcode : 4      # Opcode (OPCODE_RD_REG)
+    """)
+
+    # direct ULP address is derived from full address as follows:
+    # full:0x60008904 == ulp:(0x60008904-DR_REG_RTCCNTL_BASE) / 4
+    # full:0x60008904 == ulp:(0x60008904-0x60008000) / 4
+    # full:0x60008904 == ulp:0x904 / 4
+    # full:0x60008904 == ulp:0x241
+    # see: https://github.com/espressif/binutils-esp32ulp/blob/249ec34/gas/config/tc-esp32ulp_esp32s2.c#L78
+    ins.all = opcodes.i_reg_rd("0x60008904", "0", "0")
+    assert ins.periph_sel == 2  # high 2 bits of 0x241
+    assert ins.addr == 0x41  # low 8 bits of 0x241
+
+
 test_make_ins_struct_def()
 test_make_ins()
 test_arg_qualify()
@@ -209,3 +259,5 @@ def test_reg_address_translations_s3():
 test_reg_direct_ulp_addressing()
 test_reg_address_translations_s2()
 test_reg_address_translations_s3()
+test_reg_address_translations_s2_sens()
+test_reg_address_translations_s3_sens()