Add support for Waveshare ESP32-S3-Touch-LCD-4.3

user_setups/esp32s3/ws_esp32_s3_touch_lcd_4p3.ini

@@ -0,0 +1,86 @@
+;***************************************************;
+;   Waveshare ESP32-S3-Touch-LCD-4.3                ;
+;               - 16-bit RGB TFT                    ;
+;               - GT911 touch controller            ;
+;***************************************************;
+
+
+[ws_esp32_s3_touch]
+extends = arduino_esp32s3_v2, flash_8mb
+board = esp32-s3-devkitc-1
+board_build.arduino.memory_type = qio_opi
+
+build_flags =
+    ${arduino_esp32s3_v2.build_flags}
+    ${esp32s3.ps_ram}
+    ;-DARDUINO_USB_CDC_ON_BOOT
+	;-DUSE_USB_CDC_CONSOLE
+
+;region -- ArduinoGFX build options ------------------------
+    -D HASP_USE_ARDUINOGFX=1
+    -D HASP_LV_USE_SW_ROTATE=1
+;endregion
+
+lib_deps =
+    ${arduino_esp32s3_v2.lib_deps}
+    ${arduinogfx.lib_deps}
+    Arduino_RPi_DPI_RGBPanel_mod
+    ${goodix.lib_deps}
+
+[env:ws_esp32_s3_touch_lcd_4p3]
+extends = ws_esp32_s3_touch
+
+build_flags =
+    -D HASP_MODEL="Waveshare ESP32-S3-Touch-LCD-4.3"
+    ${ws_esp32_s3_touch.build_flags}
+    ; Bus Settings
+    -D LV_VDB_SIZE=76800 ; 10% of full framebuffer
+    -D TFT_WIDTH=800
+    -D TFT_HEIGHT=480
+    -D TFT_DE=5
+    -D TFT_VSYNC=3
+    -D TFT_HSYNC=46
+    -D TFT_PCLK=7
+    -D TFT_B0=14
+    -D TFT_B1=38
+    -D TFT_B2=18
+    -D TFT_B3=17
+    -D TFT_B4=10   
+    -D TFT_G0=39
+    -D TFT_G1=0
+    -D TFT_G2=45
+    -D TFT_G3=48
+    -D TFT_G4=47
+    -D TFT_G5=21
+    -D TFT_R0=1
+    -D TFT_R1=2
+    -D TFT_R2=42
+    -D TFT_R3=41
+    -D TFT_R4=40
+    -D TFT_BCKL=6 ; use GPIO06 as backlight PIN
+    ; Panel Settings
+    -D TFT_HSYNC_POLARITY=0
+    -D TFT_HSYNC_FRONT_PORCH=20   ; Maximum HSYNC Front Porch
+    -D TFT_HSYNC_PULSE_WIDTH=10    ; Typical HSYNC Pulse Width
+    -D TFT_HSYNC_BACK_PORCH=10    ; Typical HSYNC Back Porch
+    -D TFT_VSYNC_POLARITY=0
+    -D TFT_VSYNC_FRONT_PORCH=10   ; Maximum VSYNC Front Porch
+    -D TFT_VSYNC_PULSE_WIDTH=10   ; Typical VSYNC Pulse Width
+    -D TFT_VSYNC_BACK_PORCH=10   ; Typical VSYNC Back Porch
+    -D TFT_PCLK_ACTIVE_NEG=0
+    -D TFT_PREFER_SPEED=14000000  ; 1/2 of Typical DCLK Frequency
+    -D TFT_AUTO_FLUSH=1
+    ; Touch Settings
+    -D TOUCH_WIDTH=800
+    -D TOUCH_HEIGHT=480
+    -D TOUCH_DRIVER=0x911
+    -D TOUCH_SCL=9
+    -D TOUCH_SDA=8
+    -D TOUCH_IRQ=-1
+    -D TOUCH_RST=-1
+    -D I2C_TOUCH_ADDRESS=0x5d ; or 0x5D
+    -D I2C_TOUCH_FREQUENCY=400000
+    -D BACKLIGHT_FREQUENCY=1000 ;adopted frerquency for MP3302DJ-LF-Z (200 to 1000Hz) ->higher is better for sound!
+lib_deps =
+    ${sunton-esp32-s3-tft.lib_deps}
+    ${goodix.lib_deps}