PC Disk Drives

Drives hosted on a BlueSCSI (v1 or v2) work with IBM Compatible PCs also. Since PCs are a bit more flexible, and can be setup in multiple configurations, there are a few items to check and configure for the best possible experience.

SCSI Card Types

Discounting the card slot type, PC Compatible cards come in 2 basic types:

Cards with a BIOS
Cards without a BIOS

Cards with a BIOS

Notable Example Cards: Adaptec 2930CU, Adaptec 1522, Adaptec 1542c

SCSI cards with a BIOS will present their own setup/configuration prompt during the initial boot before DOS/Windows begins to load. These cards are bootable and allow a BlueSCSI-hosted hard drive.

Depending on your computer's BIOS and options, you may need to either change the boot order to either "A, SCSI" or "SCSI, A". Some older BIOS options may only have "C, A" or "A, C" as options. In such systems, do not use or have an IDE hard drive connected.

Cards without a BIOS

Notable Example Cards: Adaptec 2910, Adaptec 1505, Adaptec 2906

SCSI cards without a BIOS tend to be less expensive or were included with other devices like flatbed/single sheet/handheld scanners, older CD burners, CD changers, table drives, etc.

These cards are not usable to boot from without a boot loader like GRUB, Lilo, NT Boot Loader, System Commander, etc. but they are great for storage volumes and mounting/hosting CDROM drives.

Bootable Configuration Setup

If you intend to load your OS and boot from a drive presented by a BlueSCSI device (v1 or v2), there are a couple of configuration settings you need to make sure are enabled. Be sure your SCSI card has a BIOS chip first and foremost. Remember, No BIOS = No Boot.

This is not a fully comprehensive guide but will work for the vast majority of 386 and higher machines. For 8086/8088 or 286 machines, they're simpler and will just boot from the first available drive controller.

Motherboard BIOS

Make sure the motherboard's BIOS has the option for "Load option ROMs on add-in cards" and it is enabled. Some motherboard BIOSes may have it listed as "Enable bootable cards". If this is not set, then the BIOS on the SCSI card will not be allowed to load.

SCSI Card

Make sure the SCSI card's BIOS/configuration has "Enable INT 13" set as on. This ensures the card's BIOS is placed in the proper memory block for DOS/Windows (even NT, 2000, and XP) can boot after the BIOS hands off to the operating system
BlueSCSI does not support parity, nor UltraWide, so these should be disabled on your SCSI card for the ID(s) of the drives hosted on your BlueSCSI

Drives

It's unfortunate, but PCs are not as natively compatible with SCSI as Macintosh/Amiga/X68000 computers are. Please pay attention to the caveats noted below.

DOS Drive letters are assigned from the lowest SCSI ID/LUN ID to the highest, and in the following order:

Hard drives
CDROM drives
Removable drives

Hard Drives

Make sure your hard drive, the one you want to load an OS and boot from, has at least 1 Primary partition and that partition is set as Active. The DOS/Windows 95/Windows 98 installers don't always do this, resulting in a "Non-system disk" or "Option ROM invalid" error when setup reboots.

CDROM Drives

Windows (95 and above) will automatically list CDROM drives from BlueSCSI, once the Windows native drivers are loaded. DOS/Windows 3.1/3.11 will need a bit more work/effort. You will need:

DOS Real Mode driver for your SCSI card
DOS Real Mode ASPI CD driver

These are typically SYS files loaded via CONFIG.SYS. Using an Adaptec AHA-1542c ISA card as an example, you need:

ASPI4DOS.SYS - Real Mode driver for 1540/1542/1544 cards
ASPICD.SYS - Adaptec's Universal SCSI CDROM driver

In your CONFIG.SYS, you'd have:

DEVICE=C:\ASPI4DOS.SYS /D
DEVICE=C:\ASPICD.SYS /D:CDROM

And in your AUTOEXEC.BAT, you'd have:

C:\MSCDEX.EXE /D:CDROM

With this setup, you'd be able to boot to DOS and have any ISOs on your BlueSCSI show up as CDROM drive letters, fully accessible/usable in DOS and Windows 3.1/3.11. These steps are doable with Windows 95 and 98 also but the native Windows 95/98 drivers should be used instead.

Removable Drives

Removable drives, like Jaz, Zip, Magneto Optical drives, etc. can be used in DOS with either of the following options:

Enabling "Set Removable Drives as Fixed during boot" in your SCSI card's BIOS (Most PCI-based SCSI cards will have support for this) OR
Using the Real Mode drivers for the SCSI card and removable drive.

For cards without the "Set Removable Drives as Fixed" option, or cards without a BIOS, you can still use removable drives in DOS with the drivers noted above. Using an Adaptec AHA-1542c ISA card as an example once more, you need:

ASPI4DOS.SYS - Real Mode driver for 1540/1542/1544 cards
ASPIDISK.SYS - Adaptec's Universal Removable Disk driver