Replies: 9 comments 20 replies
-
|
@Nifrabar the "old" zwave graph you used to see on all applications were using only node neighbors informations, the graph z-ui show uses instead the routes provided by the controller so that is much more reliable then before, neighbors informations alone are useless and misleading based on our experience |
Beta Was this translation helpful? Give feedback.
-
|
thanks for your reply. How can I manage to show the controller provided routings? |
Beta Was this translation helpful? Give feedback.
-
|
you see them in the zwave network graph. You can also customize priority/return routes. See https://zwave-js.github.io/zwave-js-ui/#/screenshots?id=mesh |
Beta Was this translation helpful? Give feedback.
-
|
I am sorry to say but in graphics I only see the purple star being the controller and several black figures representing the nodes. Do I have to do settings to get graphic as per your example? |
Beta Was this translation helpful? Give feedback.
-
|
@Nifrabar What z-ui version are you using ? It could be your devices are battery powered so I dunno the routes till you wake up them. BTW I kindof fixed this in one of the latest releases where I considered the nlwr in the overview |
Beta Was this translation helpful? Give feedback.
-
|
@robertsLando |
Beta Was this translation helpful? Give feedback.
-
|
check the |
Beta Was this translation helpful? Give feedback.
-
|
zwave-js-ui: 9.3.1.f26b79e
zwave-js: 12.2.3
home id: 25485431
home hex: 0x184e077
This is running in docker.
Van: Daniel Lando ***@***.***>
Verzonden: dinsdag 13 februari 2024 08:23
Aan: zwave-js/zwave-js-ui ***@***.***>
CC: Nifrabar ***@***.***>; Mention ***@***.***>
Onderwerp: Re: [zwave-js/zwave-js-ui] graphic don't show 'neighbour'lines (Discussion #3599)
check the i (info) icon in topbar on the right
—
Reply to this email directly, view it on GitHub <#3599 (reply in thread)> , or unsubscribe <https://github.com/notifications/unsubscribe-auth/AEZRWBBEOZEU3XBZ7YUYGZLYTMIGTAVCNFSM6AAAAABDESGGJCVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4DINJQGE3TS> .
You are receiving this because you were mentioned. <https://github.com/notifications/beacon/AEZRWBBN3OSPKDYKL4NMGP3YTMIGTA5CNFSM6AAAAABDESGGJCWGG33NNVSW45C7OR4XAZNRIRUXGY3VONZWS33OINXW23LFNZ2KUY3PNVWWK3TUL5UWJTQAQDYIG.gif> Message ID: ***@***.*** ***@***.***> >
|
Beta Was this translation helpful? Give feedback.
-
|
That's a very old one. Please update to latest 9.8.3 |
Beta Was this translation helpful? Give feedback.
-
|
The dockercontainer which I used last week following the instructions of Domoticz Wiki came up with this (old) version. From ZwaveJs-UI it's impossible to update. I don't know how I can update now. |
Beta Was this translation helpful? Give feedback.
-
|
At long last after consulting a linux expert I managed to get the updated app. |
Beta Was this translation helpful? Give feedback.
-
|
Not all controllers provide routing information. It's possible you won't see any information if that's the case. This does not necessarily indicate any problem. Perhaps you can provide a bit more detail about your install because the information so far is limited.
|
Beta Was this translation helpful? Give feedback.
-
|
Sorry for late reply. zwave-js-ui: 9.8.3.3e632db Installed on raspberry pi v3+ OS Bullseye These are my devices. Frontend : Domoticz 2024.4 Node 2 cannot be included for unknown reason. Have reset the device and retried several times (BTW just for info and not to blame you: using OZW it was possible to include this device. Then I started from scratch. Tried to include with ZwaveJS without succes. Node 9 once disappeared form the controlpanel out of the blue. Domoticz cannot set or receive setpoint of node 9. I just tried with on/off node 11. That is OK in Domoticz although some sec delay.. Q1 is there a way to include node 2? How do I provide you with the mentioned logs? Thanks for your help and advices. |
Beta Was this translation helpful? Give feedback.
-
|
IMO Z-Stick S2 is just too old and doesn't provides routing info... |
Beta Was this translation helpful? Give feedback.
-
|
@robertsLando |
Beta Was this translation helpful? Give feedback.
-
|
@Nifrabar could you attach here an export of your nodes please? Just press on the bottom right fab on control panel, click then the purple button, and then on dump:
This will show me if any of your node do have some routes or not. Then About your other problems:
Only way to debug such issues is to make a driver log, loglevel
If the node is dead and you don't have access to that device anymore the only way is to call the remove failed node action against it. Otherwise you have to put the dead device in exclusion mode before enabling exclusion on your controller
Maybe I can answer to this when I have nodes debug export. I will be able to see the discovery payload sent to Domoticz, maybe the setpoint topic is wrong for some reason
I think this is due to your old stick but I dunno |
Beta Was this translation helpful? Give feedback.
-
|
how to? driver log is over 26 mB |
Beta Was this translation helpful? Give feedback.
-
|
none of your nodes have About the climate device I don't see any issue, try to ask in domotics forum/github issues |
Beta Was this translation helpful? Give feedback.
-
|
OK unzipped. |
Beta Was this translation helpful? Give feedback.
-
|
cc @AlCalzone |
Beta Was this translation helpful? Give feedback.
-
|
thanks fof fast repliesany suggestion for new zwave controller? Verzonden vanaf Outlook voor Android
|
Beta Was this translation helpful? Give feedback.
-
|
Zooz ZSt39 |
Beta Was this translation helpful? Give feedback.
-
Hi!
First Q here.
I have ZwaveJs-UI running since a few days.
Before I used OZW without much trouble.
One of the problems I am facing: graphics do show all nodes but not the lines in between the nodes. Is this a setting?
How to make the lines visible?
Thanks for your help.
-Bart
Beta Was this translation helpful? Give feedback.
All reactions