🐛 Redundant Temp Sensor followup (MarlinFirmware#22196)

Marlin/Configuration.h

@@ -35,7 +35,7 @@
  *
  * Advanced settings can be found in Configuration_adv.h
  */
-#define CONFIGURATION_H_VERSION 02000902
+#define CONFIGURATION_H_VERSION 02000901
 
 //===========================================================================
 //============================= Getting Started =============================
@@ -343,7 +343,6 @@
   #define MIXING_VIRTUAL_TOOLS 16  // Use the Virtual Tool method with M163 and M164
   //#define DIRECT_MIXING_IN_G1    // Allow ABCDHI mix factors in G1 movement commands
   //#define GRADIENT_MIX           // Support for gradient mixing with M166 and LCD
-  //#define MIXING_PRESETS         // Assign 8 default V-tool presets for 2 or 3 MIXING_STEPPERS
   #if ENABLED(GRADIENT_MIX)
     //#define GRADIENT_VTOOL       // Add M166 T to use a V-tool index as a Gradient alias
   #endif
@@ -368,7 +367,6 @@
 //#define PSU_NAME "Power Supply"
 
 #if ENABLED(PSU_CONTROL)
-  //#define MKS_PWC                 // Using the MKS PWC add-on
   //#define PS_OFF_CONFIRM          // Confirm dialog when power off
   //#define PS_OFF_SOUND            // Beep 1s when power off
   #define PSU_ACTIVE_STATE LOW      // Set 'LOW' for ATX, 'HIGH' for X-Box
@@ -454,7 +452,6 @@
  *    67 : 500kΩ  SliceEngineering 450°C Thermistor
  *    70 : 100kΩ  bq Hephestos 2
  *    75 : 100kΩ  Generic Silicon Heat Pad with NTC100K MGB18-104F39050L32
- *  2000 : 100kΩ  Ultimachine Rambo TDK NTCG104LH104KT1 NTC100K motherboard Thermistor
  *
  *  Analog Thermistors - 1kΩ pullup - Atypical, and requires changing out the 4.7kΩ pullup for 1kΩ.
  *  -------                           (but gives greater accuracy and more stable PID)
@@ -478,7 +475,7 @@
  *                NOTE: ADC pins are not 5V tolerant. Not recommended because it's possible to damage the CPU by going over 500°C.
  *   201 : Pt100  with circuit in Overlord, similar to Ultimainboard V2.x
  *
- *  Custom/Dummy/Other Thermal Sensors
+ *  Custom/Dummy/Other Thermos
  *  ------
  *     0 : not used
  *  1000 : Custom - Specify parameters in Configuration_adv.h
@@ -500,7 +497,6 @@
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
 #define TEMP_SENSOR_COOLER 0
-#define TEMP_SENSOR_BOARD 0
 #define TEMP_SENSOR_REDUNDANT 0
 
 // Dummy thermistor constant temperature readings, for use with 998 and 999
@@ -533,11 +529,17 @@
  * the print will be aborted. Whichever sensor is selected will have its normal functions disabled; i.e. selecting
  * the Bed sensor (-1) will disable bed heating/monitoring.
  *
- * For selecting source/target use: COOLER, PROBE, BOARD, CHAMBER, BED, E0, E1, E2, E3, E4, E5, E6, E7
+ * Use the following to select temp sensors:
+ *    -5 : Cooler
+ *    -4 : Probe
+ *    -3 : not used
+ *    -2 : Chamber
+ *    -1 : Bed
+ *   0-7 : E0 through E7
  */
 #if TEMP_SENSOR_REDUNDANT
-  #define TEMP_SENSOR_REDUNDANT_SOURCE    E1  // The sensor that will provide the redundant reading.
-  #define TEMP_SENSOR_REDUNDANT_TARGET    E0  // The sensor that we are providing a redundant reading for.
+  #define TEMP_SENSOR_REDUNDANT_SOURCE     1  // The sensor that will provide the redundant reading.
+  #define TEMP_SENSOR_REDUNDANT_TARGET     0  // The sensor that we are providing a redundant reading for.
   #define TEMP_SENSOR_REDUNDANT_MAX_DIFF  10  // (°C) Temperature difference that will trigger a print abort.
 #endif
 
@@ -596,8 +598,8 @@
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
   #if ENABLED(PID_PARAMS_PER_HOTEND)
-    // Specify up to one value per hotend here, according to your setup.
-    // If there are fewer values, the last one applies to the remaining hotends.
+    // Specify between 1 and HOTENDS values per array.
+    // If fewer than EXTRUDER values are provided, the last element will be repeated.
     #define DEFAULT_Kp_LIST {  22.20,  22.20 }
     #define DEFAULT_Ki_LIST {   1.08,   1.08 }
     #define DEFAULT_Kd_LIST { 114.00, 114.00 }
@@ -759,9 +761,6 @@
 //#define COREZY
 //#define MARKFORGED_XY  // MarkForged. See https://reprap.org/forum/read.php?152,504042
 
-// Enable for a belt style printer with endless "Z" motion
-//#define BELTPRINTER
-
 //===========================================================================
 //============================== Endstop Settings ===========================
 //===========================================================================
@@ -1115,7 +1114,7 @@
 #endif
 
 // Duet Smart Effector (for delta printers) - https://bit.ly/2ul5U7J
-// When the pin is defined you can use M672 to set/reset the probe sensitivity.
+// When the pin is defined you can use M672 to set/reset the probe sensivity.
 //#define DUET_SMART_EFFECTOR
 #if ENABLED(DUET_SMART_EFFECTOR)
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin
@@ -2160,7 +2159,6 @@
 // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
 //
 //#define INDIVIDUAL_AXIS_HOMING_MENU
-//#define INDIVIDUAL_AXIS_HOMING_SUBMENU
 
 //
 // SPEAKER/BUZZER
@@ -2417,11 +2415,6 @@
 //
 //#define MKS_MINI_12864
 
-//
-// MKS MINI12864 V3 is an alias for FYSETC_MINI_12864_2_1. Type A/B. NeoPixel RGB Backlight.
-//
-//#define MKS_MINI_12864_V3
-
 //
 // MKS LCD12864A/B with graphic controller and SD support. Follows MKS_MINI_12864 pinout.
 // https://www.aliexpress.com/item/33018110072.html
@@ -2542,39 +2535,12 @@
 // DGUS Touch Display with DWIN OS. (Choose one.)
 // ORIGIN : https://www.aliexpress.com/item/32993409517.html
 // FYSETC : https://www.aliexpress.com/item/32961471929.html
-// MKS    : https://www.aliexpress.com/item/1005002008179262.html
-//
-// Flash display with DGUS Displays for Marlin:
-//  - Format the SD card to FAT32 with an allocation size of 4kb.
-//  - Download files as specified for your type of display.
-//  - Plug the microSD card into the back of the display.
-//  - Boot the display and wait for the update to complete.
-//
-// ORIGIN (Marlin DWIN_SET)
-//  - Download https://github.com/coldtobi/Marlin_DGUS_Resources
-//  - Copy the downloaded DWIN_SET folder to the SD card.
-//
-// FYSETC (Supplier default)
-//  - Download https://github.com/FYSETC/FYSTLCD-2.0
-//  - Copy the downloaded SCREEN folder to the SD card.
-//
-// HIPRECY (Supplier default)
-//  - Download https://github.com/HiPrecy/Touch-Lcd-LEO
-//  - Copy the downloaded DWIN_SET folder to the SD card.
-//
-// MKS (MKS-H43) (Supplier default)
-//  - Download https://github.com/makerbase-mks/MKS-H43
-//  - Copy the downloaded DWIN_SET folder to the SD card.
-//
-// RELOADED (T5UID1)
-//  - Download https://github.com/Desuuuu/DGUS-reloaded/releases
-//  - Copy the downloaded DWIN_SET folder to the SD card.
 //
 //#define DGUS_LCD_UI_ORIGIN
 //#define DGUS_LCD_UI_FYSETC
 //#define DGUS_LCD_UI_HIPRECY
+
 //#define DGUS_LCD_UI_MKS
-//#define DGUS_LCD_UI_RELOADED
 #if ENABLED(DGUS_LCD_UI_MKS)
   #define USE_MKS_GREEN_UI
 #endif
@@ -2717,7 +2683,6 @@
   //#define TFT_RES_320x240
   //#define TFT_RES_480x272
   //#define TFT_RES_480x320
-  //#define TFT_RES_1024x600
 #endif
 
 /**
@@ -2757,22 +2722,6 @@
 //
 //#define DWIN_CREALITY_LCD
 
-//
-// Ender-3 v2 OEM display, enhanced.
-//
-//#define DWIN_CREALITY_LCD_ENHANCED
-
-//
-// Ender-3 v2 OEM display with enhancements by Jacob Myers
-//
-//#define DWIN_CREALITY_LCD_JYERSUI
-
-//
-// MarlinUI for Creality's DWIN display (and others)
-//
-//#define DWIN_MARLINUI_PORTRAIT
-//#define DWIN_MARLINUI_LANDSCAPE
-
 //
 // Touch Screen Settings
 //
@@ -2781,8 +2730,6 @@
   #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
   #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
 
-  //#define TOUCH_IDLE_SLEEP 300 // (secs) Turn off the TFT backlight if set (5mn)
-
   #define TOUCH_SCREEN_CALIBRATION
 
   //#define TOUCH_CALIBRATION_X 12316