vchong · pull · Jul 3, 2020 · Jun 16, 2020 · Jun 15, 2020 · Jun 15, 2020
diff --git a/Documentation/dev-tools/kunit/faq.rst b/Documentation/dev-tools/kunit/faq.rst
@@ -61,3 +61,43 @@ test, or an end-to-end test.
   kernel by installing a production configuration of the kernel on production
   hardware with a production userspace and then trying to exercise some behavior
   that depends on interactions between the hardware, the kernel, and userspace.
+
+KUnit isn't working, what should I do?
+======================================
+
+Unfortunately, there are a number of things which can break, but here are some
+things to try.
+
+1. Try running ``./tools/testing/kunit/kunit.py run`` with the ``--raw_output``
+   parameter. This might show details or error messages hidden by the kunit_tool
+   parser.
+2. Instead of running ``kunit.py run``, try running ``kunit.py config``,
+   ``kunit.py build``, and ``kunit.py exec`` independently. This can help track
+   down where an issue is occurring. (If you think the parser is at fault, you
+   can run it manually against stdin or a file with ``kunit.py parse``.)
+3. Running the UML kernel directly can often reveal issues or error messages
+   kunit_tool ignores. This should be as simple as running ``./vmlinux`` after
+   building the UML kernel (e.g., by using ``kunit.py build``). Note that UML
+   has some unusual requirements (such as the host having a tmpfs filesystem
+   mounted), and has had issues in the past when built statically and the host
+   has KASLR enabled. (On older host kernels, you may need to run ``setarch
+   `uname -m` -R ./vmlinux`` to disable KASLR.)
+4. Make sure the kernel .config has ``CONFIG_KUNIT=y`` and at least one test
+   (e.g. ``CONFIG_KUNIT_EXAMPLE_TEST=y``). kunit_tool will keep its .config
+   around, so you can see what config was used after running ``kunit.py run``.
+   It also preserves any config changes you might make, so you can
+   enable/disable things with ``make ARCH=um menuconfig`` or similar, and then
+   re-run kunit_tool.
+5. Try to run ``make ARCH=um defconfig`` before running ``kunit.py run``. This
+   may help clean up any residual config items which could be causing problems.
+6. Finally, try running KUnit outside UML. KUnit and KUnit tests can run be
+   built into any kernel, or can be built as a module and loaded at runtime.
+   Doing so should allow you to determine if UML is causing the issue you're
+   seeing. When tests are built-in, they will execute when the kernel boots, and
+   modules will automatically execute associated tests when loaded. Test results
+   can be collected from ``/sys/kernel/debug/kunit/<test suite>/results``, and
+   can be parsed with ``kunit.py parse``. For more details, see "KUnit on
+   non-UML architectures" in :doc:`usage`.
+
+If none of the above tricks help, you are always welcome to email any issues to
+[email protected].
diff --git a/Documentation/devicetree/bindings/Makefile b/Documentation/devicetree/bindings/Makefile
@@ -2,7 +2,6 @@
 DT_DOC_CHECKER ?= dt-doc-validate
 DT_EXTRACT_EX ?= dt-extract-example
 DT_MK_SCHEMA ?= dt-mk-schema
-DT_MK_SCHEMA_USERONLY_FLAG := $(if $(DT_SCHEMA_FILES), -u)
 
 DT_SCHEMA_MIN_VERSION = 2020.5
 
@@ -35,21 +34,40 @@ quiet_cmd_mk_schema = SCHEMA  $@
 
 DT_DOCS = $(shell $(find_cmd) | sed -e 's|^$(srctree)/||')
 
-DT_SCHEMA_FILES ?= $(DT_DOCS)
-
-extra-$(CHECK_DT_BINDING) += $(patsubst $(src)/%.yaml,%.example.dts, $(DT_SCHEMA_FILES))
-extra-$(CHECK_DT_BINDING) += $(patsubst $(src)/%.yaml,%.example.dt.yaml, $(DT_SCHEMA_FILES))
-extra-$(CHECK_DT_BINDING) += processed-schema-examples.yaml
-
 override DTC_FLAGS := \
 	-Wno-avoid_unnecessary_addr_size \
-	-Wno-graph_child_address
+	-Wno-graph_child_address \
+	-Wno-interrupt_provider
 
 $(obj)/processed-schema-examples.yaml: $(DT_DOCS) check_dtschema_version FORCE
 	$(call if_changed,mk_schema)
 
-$(obj)/processed-schema.yaml: DT_MK_SCHEMA_FLAGS := $(DT_MK_SCHEMA_USERONLY_FLAG)
+ifeq ($(DT_SCHEMA_FILES),)
+
+# Unless DT_SCHEMA_FILES is specified, use the full schema for dtbs_check too.
+# Just copy processed-schema-examples.yaml
+
+$(obj)/processed-schema.yaml: $(obj)/processed-schema-examples.yaml FORCE
+	$(call if_changed,copy)
+
+DT_SCHEMA_FILES = $(DT_DOCS)
+
+else
+
+# If DT_SCHEMA_FILES is specified, use it for processed-schema.yaml
+
+$(obj)/processed-schema.yaml: DT_MK_SCHEMA_FLAGS := -u
 $(obj)/processed-schema.yaml: $(DT_SCHEMA_FILES) check_dtschema_version FORCE
 	$(call if_changed,mk_schema)
 
-extra-y += processed-schema.yaml
+endif
+
+extra-$(CHECK_DT_BINDING) += $(patsubst $(src)/%.yaml,%.example.dts, $(DT_SCHEMA_FILES))
+extra-$(CHECK_DT_BINDING) += $(patsubst $(src)/%.yaml,%.example.dt.yaml, $(DT_SCHEMA_FILES))
+extra-$(CHECK_DT_BINDING) += processed-schema-examples.yaml
+extra-$(CHECK_DTBS) += processed-schema.yaml
+
+# Hack: avoid 'Argument list too long' error for 'make clean'. Remove most of
+# build artifacts here before they are processed by scripts/Makefile.clean
+clean-files = $(shell find $(obj) \( -name '*.example.dts' -o \
+			-name '*.example.dt.yaml' \) -delete 2>/dev/null)
diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
@@ -47,7 +47,7 @@ Required properties:
 			  &lsio_mu1 1 2
 			  &lsio_mu1 1 3
 			  &lsio_mu1 3 3>;
-		See Documentation/devicetree/bindings/mailbox/fsl,mu.txt
+		See Documentation/devicetree/bindings/mailbox/fsl,mu.yaml
 		for detailed mailbox binding.
 
 Note: Each mu which supports general interrupt should have an alias correctly

diff --git a/Documentation/devicetree/bindings/bus/socionext,uniphier-system-bus.yaml b/Documentation/devicetree/bindings/bus/socionext,uniphier-system-bus.yaml
@@ -80,14 +80,14 @@ examples:
         ranges = <1 0x00000000 0x42000000 0x02000000>,
                  <5 0x00000000 0x46000000 0x01000000>;
 
-        ethernet@1,01f00000 {
+        ethernet@1,1f00000 {
             compatible = "smsc,lan9115";
             reg = <1 0x01f00000 0x1000>;
             interrupts = <0 48 4>;
             phy-mode = "mii";
         };
 
-        uart@5,00200000 {
+        serial@5,200000 {
             compatible = "ns16550a";
             reg = <5 0x00200000 0x20>;
             interrupts = <0 49 4>;

diff --git a/Documentation/devicetree/bindings/clock/imx27-clock.yaml b/Documentation/devicetree/bindings/clock/imx27-clock.yaml
@@ -7,7 +7,7 @@ $schema: http://devicetree.org/meta-schemas/core.yaml#
 title: Clock bindings for Freescale i.MX27
 
 maintainers:
-  - Fabio Estevam <fabio.estevam@freescale.com>
+  - Fabio Estevam <fabio.estevam@nxp.com>
 
 description: |
   The clock consumer should specify the desired clock by having the clock

diff --git a/Documentation/devicetree/bindings/clock/imx31-clock.yaml b/Documentation/devicetree/bindings/clock/imx31-clock.yaml
@@ -7,7 +7,7 @@ $schema: http://devicetree.org/meta-schemas/core.yaml#
 title: Clock bindings for Freescale i.MX31
 
 maintainers:
-  - Fabio Estevam <fabio.estevam@freescale.com>
+  - Fabio Estevam <fabio.estevam@nxp.com>
 
 description: |
   The clock consumer should specify the desired clock by having the clock

diff --git a/Documentation/devicetree/bindings/clock/imx5-clock.yaml b/Documentation/devicetree/bindings/clock/imx5-clock.yaml
@@ -7,7 +7,7 @@ $schema: http://devicetree.org/meta-schemas/core.yaml#
 title: Clock bindings for Freescale i.MX5
 
 maintainers:
-  - Fabio Estevam <fabio.estevam@freescale.com>
+  - Fabio Estevam <fabio.estevam@nxp.com>
 
 description: |
   The clock consumer should specify the desired clock by having the clock

diff --git a/Documentation/devicetree/bindings/display/bridge/sii902x.txt b/Documentation/devicetree/bindings/display/bridge/sii902x.txt
@@ -37,7 +37,7 @@ Optional properties:
 	simple-card or audio-graph-card binding. See their binding
 	documents on how to describe the way the sii902x device is
 	connected to the rest of the audio system:
-	Documentation/devicetree/bindings/sound/simple-card.txt
+	Documentation/devicetree/bindings/sound/simple-card.yaml
 	Documentation/devicetree/bindings/sound/audio-graph-card.txt
 	Note: In case of the audio-graph-card binding the used port
 	index should be 3.

diff --git a/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt
@@ -68,7 +68,7 @@ Required properties:
   datasheet
 - clocks : phandle to the PRE axi clock input, as described
   in Documentation/devicetree/bindings/clock/clock-bindings.txt and
-  Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+  Documentation/devicetree/bindings/clock/imx6q-clock.yaml.
 - clock-names: should be "axi"
 - interrupts: should contain the PRE interrupt
 - fsl,iram: phandle pointing to the mmio-sram device node, that should be
@@ -94,7 +94,7 @@ Required properties:
   datasheet
 - clocks : phandles to the PRG ipg and axi clock inputs, as described
   in Documentation/devicetree/bindings/clock/clock-bindings.txt and
-  Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+  Documentation/devicetree/bindings/clock/imx6q-clock.yaml.
 - clock-names: should be "ipg" and "axi"
 - fsl,pres: phandles to the PRE units attached to this PRG, with the fixed
   PRE as the first entry and the muxable PREs following.

diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt
@@ -30,8 +30,8 @@ Required properties:
                 "di2_sel" - IPU2 DI0 mux
                 "di3_sel" - IPU2 DI1 mux
         The needed clock numbers for each are documented in
-        Documentation/devicetree/bindings/clock/imx5-clock.txt, and in
-        Documentation/devicetree/bindings/clock/imx6q-clock.txt.
+        Documentation/devicetree/bindings/clock/imx5-clock.yaml, and in
+        Documentation/devicetree/bindings/clock/imx6q-clock.yaml.
 
 Optional properties:
  - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q

diff --git a/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.yaml b/Documentation/devicetree/bindings/display/panel/arm,versatile-tft-panel.yaml
@@ -33,7 +33,7 @@ additionalProperties: false
 
 examples:
   - |
-    sysreg {
+    sysreg@0 {
         compatible = "arm,versatile-sysreg", "syscon", "simple-mfd";
         reg = <0x00000 0x1000>;
 

diff --git a/Documentation/devicetree/bindings/display/rockchip/rockchip-drm.yaml b/Documentation/devicetree/bindings/display/rockchip/rockchip-drm.yaml
@@ -24,7 +24,7 @@ properties:
     description: |
       Should contain a list of phandles pointing to display interface port
       of vop devices. vop definitions as defined in
-      Documentation/devicetree/bindings/display/rockchip/rockchip-vop.txt
+      Documentation/devicetree/bindings/display/rockchip/rockchip-vop.yaml
 
 required:
   - compatible

diff --git a/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt b/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt
@@ -12,7 +12,7 @@ Required properties for the top level node:
    Only the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
 - #interrupt-cells : Specifies the number of cells needed to encode an
    interrupt. Should be 2. The first cell defines the interrupt number,
-   the second encodes the triger flags encoded as described in
+   the second encodes the trigger flags encoded as described in
    Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
 - compatible:
   - "mediatek,mt7621-gpio" for Mediatek controllers

diff --git a/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt
@@ -10,7 +10,7 @@ Interrupt number definition:
  16-31  : private  irq, and we use 16 as the co-processor timer.
  31-1024: common irq for soc ip.
 
-Interrupt triger mode: (Defined in dt-bindings/interrupt-controller/irq.h)
+Interrupt trigger mode: (Defined in dt-bindings/interrupt-controller/irq.h)
  IRQ_TYPE_LEVEL_HIGH (default)
  IRQ_TYPE_LEVEL_LOW
  IRQ_TYPE_EDGE_RISING

diff --git a/Documentation/devicetree/bindings/mailbox/xlnx,zynqmp-ipi-mailbox.txt b/Documentation/devicetree/bindings/mailbox/xlnx,zynqmp-ipi-mailbox.txt
@@ -87,7 +87,7 @@ Example:
 		ranges;
 
 		/* APU<->RPU0 IPI mailbox controller */
-		ipi_mailbox_rpu0: mailbox@ff90400 {
+		ipi_mailbox_rpu0: mailbox@ff990400 {
 			reg = <0xff990400 0x20>,
 			      <0xff990420 0x20>,
 			      <0xff990080 0x20>,

diff --git a/Documentation/devicetree/bindings/misc/olpc,xo1.75-ec.txt b/Documentation/devicetree/bindings/misc/olpc,xo1.75-ec.txt
@@ -8,7 +8,7 @@ The embedded controller requires the SPI controller driver to signal readiness
 to receive a transfer (that is, when TX FIFO contains the response data) by
 strobing the ACK pin with the ready signal. See the "ready-gpios" property of the
 SSP binding as documented in:
-<Documentation/devicetree/bindings/spi/spi-pxa2xx.txt>.
+<Documentation/devicetree/bindings/spi/marvell,mmp2-ssp.yaml>.
 
 Example:
 	&ssp3 {

diff --git a/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt
@@ -3,7 +3,7 @@ MediaTek SoC built-in Bluetooth Devices
 
 This device is a serial attached device to BTIF device and thus it must be a
 child node of the serial node with BTIF. The dt-bindings details for BTIF
-device can be known via Documentation/devicetree/bindings/serial/8250.txt.
+device can be known via Documentation/devicetree/bindings/serial/8250.yaml.
 
 Required properties:
 

diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt
@@ -114,7 +114,7 @@ with values derived from the SoC user manual.
    [flags]>
 
 On other mach-shmobile platforms GPIO is handled by the gpio-rcar driver.
-Please refer to Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt
+Please refer to Documentation/devicetree/bindings/gpio/renesas,rcar-gpio.yaml
 for documentation of the GPIO device tree bindings on those platforms.
 
 

diff --git a/Documentation/devicetree/bindings/sound/audio-graph-card.txt b/Documentation/devicetree/bindings/sound/audio-graph-card.txt
@@ -5,7 +5,7 @@ It is based on common bindings for device graphs.
 see ${LINUX}/Documentation/devicetree/bindings/graph.txt
 
 Basically, Audio Graph Card property is same as Simple Card.
-see ${LINUX}/Documentation/devicetree/bindings/sound/simple-card.txt
+see ${LINUX}/Documentation/devicetree/bindings/sound/simple-card.yaml
 
 Below are same as Simple-Card.
 

diff --git a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt
@@ -5,7 +5,7 @@ codec or external codecs.
 
 sti sound drivers allows to expose sti SoC audio interface through the
 generic ASoC simple card. For details about sound card declaration please refer to
-Documentation/devicetree/bindings/sound/simple-card.txt.
+Documentation/devicetree/bindings/sound/simple-card.yaml.
 
 1) sti-uniperiph-dai: audio dai device.
 ---------------------------------------

diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt
@@ -19,7 +19,7 @@ Required properties:
 
 SPI Controller nodes must be child of GENI based Qualcomm Universal
 Peripharal. Please refer GENI based QUP wrapper controller node bindings
-described in Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt.
+described in Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml.
 
 SPI slave nodes must be children of the SPI master node and conform to SPI bus
 binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt.

diff --git a/Documentation/devicetree/bindings/thermal/thermal-sensor.yaml b/Documentation/devicetree/bindings/thermal/thermal-sensor.yaml
@@ -41,7 +41,7 @@ examples:
     #include <dt-bindings/interrupt-controller/arm-gic.h>
 
     // Example 1: SDM845 TSENS
-    soc: soc@0 {
+    soc: soc {
             #address-cells = <2>;
             #size-cells = <2>;
 

diff --git a/Documentation/devicetree/bindings/thermal/thermal-zones.yaml b/Documentation/devicetree/bindings/thermal/thermal-zones.yaml
@@ -224,7 +224,7 @@ examples:
     #include <dt-bindings/thermal/thermal.h>
 
     // Example 1: SDM845 TSENS
-    soc: soc@0 {
+    soc {
             #address-cells = <2>;
             #size-cells = <2>;
 

diff --git a/Documentation/devicetree/bindings/thermal/ti,am654-thermal.yaml b/Documentation/devicetree/bindings/thermal/ti,am654-thermal.yaml
@@ -35,7 +35,7 @@ examples:
     #include <dt-bindings/soc/ti,sci_pm_domain.h>
     vtm: thermal@42050000 {
         compatible = "ti,am654-vtm";
-        reg = <0x0 0x42050000 0x0 0x25c>;
+        reg = <0x42050000 0x25c>;
         power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
         #thermal-sensor-cells = <1>;
     };

diff --git a/Documentation/devicetree/bindings/timer/csky,mptimer.txt b/Documentation/devicetree/bindings/timer/csky,mptimer.txt
@@ -8,7 +8,7 @@ regs is accessed by cpu co-processor 4 registers with mtcr/mfcr.
  - PTIM_CTLR "cr<0, 14>" Control reg to start reset timer.
  - PTIM_TSR  "cr<1, 14>" Interrupt cleanup status reg.
  - PTIM_CCVR "cr<3, 14>" Current counter value reg.
- - PTIM_LVR  "cr<6, 14>" Window value reg to triger next event.
+ - PTIM_LVR  "cr<6, 14>" Window value reg to trigger next event.
 
 ==============================
 timer node bindings definition

diff --git a/Documentation/devicetree/bindings/usb/aspeed,usb-vhub.yaml b/Documentation/devicetree/bindings/usb/aspeed,usb-vhub.yaml
@@ -127,8 +127,8 @@ examples:
                 #address-cells = <1>;
                 #size-cells = <0>;
 
-                string@0409 {
-                        reg = <0x0409>;
+                string@409 {
+                        reg = <0x409>;
                         manufacturer = "ASPEED";
                         product = "USB Virtual Hub";
                         serial-number = "0000";

diff --git a/Documentation/devicetree/writing-schema.rst b/Documentation/devicetree/writing-schema.rst
@@ -1,4 +1,4 @@
-:orphan:
+.. SPDX-License-Identifier: GPL-2.0
 
 Writing DeviceTree Bindings in json-schema
 ==========================================
@@ -124,9 +124,12 @@ dtc must also be built with YAML output support enabled. This requires that
 libyaml and its headers be installed on the host system. For some distributions
 that involves installing the development package, such as:
 
-Debian:
+Debian::
+
   apt-get install libyaml-dev
-Fedora:
+
+Fedora::
+
   dnf -y install libyaml-devel
 
 Running checks

diff --git a/Documentation/mips/ingenic-tcu.rst b/Documentation/mips/ingenic-tcu.rst
@@ -68,4 +68,4 @@ and frameworks can be controlled from the same registers, all of these
 drivers access their registers through the same regmap.
 
 For more information regarding the devicetree bindings of the TCU drivers,
-have a look at Documentation/devicetree/bindings/timer/ingenic,tcu.txt.
+have a look at Documentation/devicetree/bindings/timer/ingenic,tcu.yaml.
diff --git a/MAINTAINERS b/MAINTAINERS
@@ -3946,7 +3946,7 @@ L:	[email protected]
 S:	Supported
 F:	drivers/char/hw_random/cctrng.c
 F:	drivers/char/hw_random/cctrng.h
-F:	Documentation/devicetree/bindings/rng/arm-cctrng.txt
+F:	Documentation/devicetree/bindings/rng/arm-cctrng.yaml
 W:	https://developer.arm.com/products/system-ip/trustzone-cryptocell/cryptocell-700-family
 
 CEC FRAMEWORK
@@ -5490,7 +5490,7 @@ F:	include/uapi/drm/r128_drm.h
 DRM DRIVER FOR RAYDIUM RM67191 PANELS
 M:	Robert Chiras <[email protected]>
 S:	Maintained
-F:	Documentation/devicetree/bindings/display/panel/raydium,rm67191.txt
+F:	Documentation/devicetree/bindings/display/panel/raydium,rm67191.yaml
 F:	drivers/gpu/drm/panel/panel-raydium-rm67191.c
 
 DRM DRIVER FOR ROCKTECH JH057N00900 PANELS
@@ -14574,8 +14574,8 @@ RENESAS R-CAR THERMAL DRIVERS
 M:	Niklas Söderlund <[email protected]>
 L:	[email protected]
 S:	Supported
-F:	Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt
-F:	Documentation/devicetree/bindings/thermal/rcar-thermal.txt
+F:	Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.yaml
+F:	Documentation/devicetree/bindings/thermal/rcar-thermal.yaml
 F:	drivers/thermal/rcar_gen3_thermal.c
 F:	drivers/thermal/rcar_thermal.c