двигатели 900 ма

ursoft · Apr 28, 2020 · fa0a381 · fa0a381
1 parent 8412472
commit fa0a381
Showing 1 changed file with 5 additions and 5 deletions.
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
@@ -432,7 +432,7 @@
 #if (GITHUB_USER==URSOFT)
  #define EXTRUDER_AUTO_FAN_SPEED 100
 #else
- #define EXTRUDER_AUTO_FAN_SPEED 100   // 255 == full speed было 200
+ #define EXTRUDER_AUTO_FAN_SPEED 120   // 255 == full speed было 200
 #endif
 #define EXTRUDER_AUTO_FAN_SPEED_CONFIGURABLE
 //#define CHAMBER_AUTO_FAN_TEMPERATURE 30
@@ -1900,7 +1900,7 @@
                                                   // This short retract is done immediately, before parking the nozzle.
   #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     60  // (mm/s) Unload filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_UNLOAD_LENGTH      790  // (mm) The length of filament for a complete unload.
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH      650  // (mm) The length of filament for a complete unload.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
                                                   //   Set to 0 for manual unloading.
@@ -1909,7 +1909,7 @@
                                                   // 0 to disable start loading and skip to fast load only
   #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE  60  // (mm/s) Load filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_FAST_LOAD_ACCEL     25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH   790  // (mm) Load length of filament, from extruder gear to nozzle.
+  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH   650  // (mm) Load length of filament, from extruder gear to nozzle.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
   //#define ADVANCED_PAUSE_CONTINUOUS_PURGE       // Purge continuously up to the purge length until interrupted.
@@ -2070,7 +2070,7 @@
   #define INTERPOLATE       true  // Interpolate X/Y/Z_MICROSTEPS to 256 Включает или выключает интерполяцию по ВСЕМ осям
 
   #if AXIS_IS_TMC(X)
-    #define X_CURRENT       800        // (mA) RMS current. Multiply by 1.414 for peak current. сюда пишем наш ток Irms, который мы посчитали ранее
+    #define X_CURRENT       900        // (mA) RMS current. Multiply by 1.414 for peak current. сюда пишем наш ток Irms, который мы посчитали ранее
     #define X_CURRENT_HOME  X_CURRENT  // (mA) RMS current for sensorless homing
     #define X_MICROSTEPS     16    // 0..256 количество микрошагов, поддерживается нативно до 256, не забываем изменить число шагов на мм
     #define X_RSENSE          0.11  // Если на Ваших драйверах резистор Rsense отличается от стандартного R110, сюда вписываем номинал
@@ -2086,7 +2086,7 @@
   #endif
 
   #if AXIS_IS_TMC(Y)
-    #define Y_CURRENT       800
+    #define Y_CURRENT       900
     #define Y_CURRENT_HOME  Y_CURRENT
     #define Y_MICROSTEPS     16
     #define Y_RSENSE          0.11