device: netberg: Add sensors.conf and update platform modules package

Now hardware monitoring platform driver implements lm-sensors compatible
sysfs ABI we can add sensors.conf file to describe various platforms
features with their subfeatures to sensord(8) running in pmon container.

Now both sensors(1) and "show environment" work well from SONiC cmdline.

Note that hardware_monitor platform driver is in change of controlling
FAN speed and implements thermal policy: there is no need in fancontrol
configuration for platforms handled by this driver.

Adjust platform modules package version and update submodules reference.

Signed-off-by: Sergey Popovich <[email protected]>

device/netberg/x86_64-netberg_aurora_420_rangeley-r0/sensors.conf

@@ -0,0 +1,60 @@
+# This is lm-sensors configuration file for Netberg Aurora 420 switch.
+#
+# Label names are taken from "Specification of Hardware Monitoring
+# Driver for Open Network Linux" guide (filename: HW_monitoring_ONL.pdf).
+#
+# Assume following hardware monitoring modules loaded:
+#
+#    hardware_monitor - implements HURACAN (w83795adg based) sensor,
+#                       fan control, watchdog and SFP control.
+#    jc42             - DIMM temperature sensor (?)
+#    coretemp         - Processor cores temperature sensor
+#
+
+bus "i2c-1" "SMBus iSMT adapter at dff38000"
+bus "i2c-0" "SMBus I801 adapter at f000"
+
+chip "jc42-i2c-0-*"
+	label temp1 "DIMM Temp"
+	set temp1_max 50
+	set temp1_crit 85
+
+chip "HURACAN-i2c-0-2f"
+	# 6.1.2. For Aurora 420 platform, p.31
+	label in1 "ROV"
+	label in4 "1V"
+	label in5 "1.8V"
+	label in7 "1.25V"
+
+	# 2.1. Temperature, p.7
+	label temp1 "After MAC"
+	label temp2 "Before MAC"
+	# MAC Temp is set by application
+	label temp10 "MAC"
+
+chip "HURACAN-i2c-1-70"
+	# 2.3.4. VOUT, p.11
+	label in12 "PSU1_VOUT"
+	label in22 "PSU2_VOUT"
+
+	# 2.3.5. IOUT, p.11
+	label curr12 "PSU1_IOUT"
+	label curr22 "PSU2_IOUT"
+
+	# 2.3.9. PIN, p.12
+	label power11 "PSU1_PIN"
+	label power21 "PSU2_PIN"
+
+	# 2.3.8. POUT, p.12
+	label power12 "PSU1_POUT"
+	label power22 "PSU2_POUT"
+
+	# 2.3.6. TEMPERATURE, p.11
+	label temp11 "PSU1_TEMP1"
+	label temp12 "PSU1_TEMP2"
+	label temp21 "PSU2_TEMP1"
+	label temp22 "PSU2_TEMP2"
+
+	# 2.3.7. FAN SPEED, p.11
+	label fan11 "PSU1_FAN"
+	label fan21 "PSU2_FAN"

platform/broadcom/platform-modules-netberg.mk

@@ -1,6 +1,6 @@
 # Netberg Platform modules
 
-NETBERG_PLATFORM_MODULE_VERSION = 0.5
+NETBERG_PLATFORM_MODULE_VERSION = 0.6
 
 export NETBERG_PLATFORM_MODULE_VERSION
 

platform/broadcom/sonic-platform-modules-netberg/debian/changelog

@@ -1,3 +1,11 @@
+sonic-platform-netberg (0.6) unstable; urgency=low
+
+  * Support lm-sensors compatible sysfs ABI.
+  * Make sure coretemp and jc42 kernel drivers loaded.
+  * Bump version to 0.6.
+
+ -- Sergey Popovich <[email protected]>  Sat, 22 Dec 2018 17:18:52 +0200
+
 sonic-platform-netberg (0.5) unstable; urgency=low
 
   * Fix dependency on linux-image after switching from jessie to stretch

platform/broadcom/sonic-platform-modules-netberg/debian/platform-modules-netberg.postinst

@@ -1,6 +1,7 @@
 # postinst script for Netberg devices
 
 # Unload hardware monitoring module, if any
+modprobe -q -r jc42 ||:
 modprobe -q -r hardware_monitor ||:
 
 # Unload modules required for hardware monitoring
@@ -18,6 +19,8 @@ modprobe -q -r i2c-dev ||:
 #DEBHELPER#
 
 # Load hardware monitoring module
+modprobe -q coretemp ||:
+modprobe -q jc42 ||:
 modprobe -q hardware_monitor ||:
 
 # Make sure modprobe.d(5) is in initramfs

platform/broadcom/sonic-platform-modules-netberg/netberg/cfg/netberg-modprobe.conf

@@ -9,4 +9,5 @@ softdep i2c-isch pre: i2c-i801
 # they are depend on it anyway.
 
 # Hardware monitoring devices reside on i2c bus.
+softdep jc42 pre: i2c-dev i2c-i801
 softdep hardware_monitor pre: i2c-dev i2c-i801 i2c-ismt i2c-isch i2c-mux-gpio i2c-mux-pca954x

platform/broadcom/sonic-platform-modules-netberg/netberg/cfg/netberg-modules-load.conf

@@ -3,4 +3,6 @@
 # This file contains the names of kernel modules that should be loaded
 # at boot time, one per line. Lines beginning with "#" are ignored.
 
+coretemp
+jc42
 hardware_monitor