The Atmel SAM D21 microcontroller on Tessel 2 serves several purposes:
- Controls the two module ports' GPIO, SPI, UART, I2C, and ADC interfaces from the SoC
- Transfers data and commands between USB and the SoC for the Tessel CLI
- Provides a USB serial console for the SoC
- Programs the SoC's SPI flash over USB
- Manages SoC and module port power state
firmware/-- The main SAMD21 firmware sourcecommon/-- Utilities for SAMD21 peripherals and board-specific headersdeps/-- Dependency submodules: Atmel headers and USB stackboot/-- USB DFU bootloadersoc/-- Bridge daemon running on the SoC that communicates with the MCU over SPInode/-- Node libraries for controlling the module ports via the MCU
The SPI bridge between the MT7620n ("SoC") and SAMD21 ("MCU") is modeled loosely on USB, and provides three bidirectional channels between Unix domain sockets on the Linux environment of the SoC and various functions in the MCU firmware. Pipe 0 is connected to a pair of USB endpoints and used for Tessel CLI communication with the Linux system. Pipes 1 and 2 are used for control of the two Tessel module ports.
- MOSI, MISO, SCK, CS1 -- SPI lines. SoC is SPI master, MCU is SPI slave
- SYNC -- driven low by the SoC during setup transfers, driven high by the SoC during data transfers
- IRQ -- driven high by the MCU when it wants to be polled by the SoC because it has data to send or has become ready to receive
Note that the MT7620 SPI controller is designed only to talk to SPI flash and is not full duplex, and the protocol designs around this limitation.
A transaction has a setup phase and an optional data phase. To begin the setup phase, the SoC brings SYNC low. On this pin change, the MCU prepares a DMA chain for the setup transfer. In the setup transfer, each side provides:
- A magic number, to verify correct operation
- Bits specifying which channels are connected
- Bits specifying which channels for which this side is ready to accept data
- A byte for each channel specifying the data length ready to be sent on that channel
After this information is exchanged, both sides can compute the contents of the data transfer. If one side is ready to accept data on that channel and the other sends a nonzero length, the transfer will be performed. Otherwise that channel-direction is ignored for this transaction, and the writable bit or length count are repeated in future transfers until the other is present. The SoC drives SYNC high to begin the data phase.
The data transfer payload contains the channel payloads in channel order. There is no framing information in the data transfer, as it was derived from the setup payload. The MCU sets up a chain of DMA operations between the SPI controller and the provided buffers.
Each port has an independent command queue, which is accessed through a Unix domain socket on the Linux SoC. Node or other software can submit a batch of actions that are sent in a single bridge transaction which are executed in order and replies sent back via bridge and domain socket.
Some replies (pin change interrupt, UART receive) are asynchronously inserted into the stream of in-order replies.
The eventual goal is that the SoC will send larger command batches or macros to be executed in real-time, isolated from the Linux preemptive scheduler and Node garbage collector.
Building the firmware requires gcc-arm-embedded.
To install quickly on a Mac with Homebrew:
brew tap tessel/tools
brew install gcc-arm
Use the gcc-arm-embedded PPA:
sudo add-apt-repository ppa:terry.guo/gcc-arm-embedded && sudo apt-get update
sudo apt-get install git gcc-arm-none-eabi
git clone https://github.com/tessel/t2-firmware --recursive
cd t2-firmware
make
dfu-util is a command line utility to update the firmware on T2. See their website for installation instructions (brew install dfu-util works).
Plug the USB port your T2 into your computer while holding down the button by the Tessel 2 logo - this will put T2 into bootloader mode, with the power LED blinking.
Now flash the device:
➜ dfu-util -aFlash -d 1209:7551 -D build/firmware.bin
...
dfu-util: Invalid DFU suffix signature
dfu-util: A valid DFU suffix will be required in a future dfu-util release!!!
Opening DFU capable USB device...
ID 1209:7551
Run-time device DFU version 0101
Claiming USB DFU Interface...
Setting Alternate Setting #0 ...
Determining device status: state = dfuIDLE, status = 0
dfuIDLE, continuing
DFU mode device DFU version 0101
Device returned transfer size 256
Copying data from PC to DFU device
Download [=========================] 100% 12524 bytes
Download done.
state(7) = dfuMANIFEST, status(0) = No error condition is present
dfu-util: unable to read DFU status after completion
That should be it! Don't worry about the final warning at the bottom - it doesn't seem to affect anything.
Note that this only updates the firmware on the SAMD21 coprocessor. You will need to update OpenWrt on the SoC separately. Eventually this process will be integrated as the tessel update command.
Solder an 0.05in header on J401 next to port A.
We use the Bus Blaster v3 with a Cortex Debug adapter cable.
It needs to be flashed to support SWD.
Then run:
arm-none-eabi-gdb build/firmware.elf -ex 'target remote | openocd -c "gdb_port pipe; tcl_port 0; telnet_port 0" -f scripts/d21.cfg'
One of Tessel's unique features is the ability to program and debug the SAMD21 coprocessor from the
MT7620 SoC without an external SWD adapter. The SAMD21 SWD pins are connected to GPIOs on the SoC,
allowing openocd to bitbang the SWD protocol.
Log into your Tessel via SSH over WiFi or Ethernet. USB console is implemented in the SAMD21, and will be unavailable while that processor is stopped.
Run the following commands to install and start openocd.
opkg update
opkg install openocd
cat > openocd.cfg <<EOF
interface sysfsgpio
transport select swd
sysfsgpio_swd_nums 41 42
source [find target/at91samdXX.cfg]
EOF
openocd -f openocd.cfg
Then, in a checkout of this repository after compiling:
arm-none-eabi-gdb build/firmware.elf -ex 'target remote <tessel ip>:3333'
Warning: You probably do not need to do this. If the bootloader is intact, every other piece of software on Tessel can be fixed over USB. If you break the SAMD21 bootloader and can't boot or access the SoC, you'll need a SWD adapter to recover the device.
One of the duties of the SAMD21 is to sequence SoC power rails on bootup. Without it, the SoC may not boot reliably. If you do this with onboard SWD, be very careful, and don't power down the Tessel until you confirm that your computer recognizes the new bootloader over USB.
Compile the firmware, follow the openocd setup instructions above, then run:
$ arm-none-eabi-gdb build/boot.elf -ex 'target remote <tessel ip>:3333'
(gdb) load
(gdb) compare-sections
(gdb) mon reset run