Skip to content

rogerdahl/ws2812b-neopixel-emulator

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

32 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Adafruit NeoPixel Emulator

This is a tool to speed up development of animated patterns for WS2812B RGB LEDs that are supported by the Adafruit NeoPixel library for Arduino. It consists of a library that has the same interface as the NeoPixel library but that, instead of writing to actual WS2812B LEDs, renders the LEDs on screen using OpenGL. In addition, there's simple adapter code and implementations of a couple of the most common functions used in Arduino sketches (delay(), random() and millis()).

This allows an Arduino sketch that uses only the Adafruit NeoPixel library and the supported functions to be compiled, linked and run on the PC, enabling a shorter development cycle and easy debugging for WS2812B blinkenlight projects.

After implementing the desired effects on the PC, the sketch can be copied unchanged to the Arduino IDE for programming one of the Atmel AVR MCUs supported by the Adafruit NeoPixel library.

Strip, Grid and Ring layouts are supported for the on-screen rendering of the LEDs. For instance a layout resembling the 24 LED Adafruit NeoPixel Ring, can be set up by selecting the Ring layout with 24 pixels. The selection is done by calling setPixelLayout() in the sketch. Only the emulator has the method, so the preprocessor is used for skipping the call when building for an MCU. This is demonstrated in the included sketch.

This was used for developing some NeoPixel patterns for a DigiSpark ATtiny85. The DigiSpark is a convenient platform for running battery powered blinky lights but is not so convenient for development as it must be unplugged and plugged back into the USB port each time the code is updated (which can easily be hundreds of times when tweaking parameters for animated effects, etc). Hence this small app.

Setup and Use

As Douglas Adams might have said, getting things up and running with this app is almost, but not quite, entirely unlike getting things running on an Arduino. No part of the Arduino IDE or libraries are used in this project. It's just a regular PC app written in C++ and based on FreeGLUT that has been set up in such a way that one of the .cpp files can also be used as an Arduino sketch. The app should compile and run on any platform where FreeGLUT is available, such as Linux, Mac and Windows.

Build on Linux

These instructions should work on Ubuntu, Mint and other Debian based systems. Tested on Linux Mint 18.3 64-bit.

Compiler and stuff
$ sudo apt-get install build-essential
freeGLUT
$ sudo apt-get install freeglut3-dev
source

Grab the code directly from this repository:

$ git clone <copy and paste the clone URL from the top of this page>
$ cd ws2812b-neopixel-emulator
OpenGL

You also need OpenGL drivers. These are specific to your graphics card and you probably already have them. If they appear to be missing, it's worth a try to set up the Mesa drivers:

$ sudo apt-get install mesa-common-dev (*install these only if you need them*)

Compile and run:

$ mkdir cmake-build
$ cd cmake-build
$ cmake ..
$ make
$ ../bin/emulator
  • Watch the blinkies on screen. Then exit by closing the window or hitting Ctrl-C in the shell.

  • Tweak arduino_sketch.cpp to make your own animations.

  • If working with multiple sketches, set the filename of the one to build in the SKETCH variable, close to the top in CMakeLists.txt.

  • Debug with a regular debugger or use printf() statements (the output appears in the shell).

  • When done, copy paste the arduino_sketch.cpp code into the Arduino IDE and write it to your device.

Notes

  • The setBrightness() call is ignored by the emulator and the getBrightness() call always returns the maximum brightness value of 255. As described on the NeoPixel library home page, setBrightness() is "lossy" and intended for use only in setup(), not in animations. Since physical LEDs are brighter than a computer monitor even on low brightness settings, the LEDs are most accurately represented by rendering them with maximum brightness. By having the emulator ignore setBrightness(), the call can be used in the sketch to set the brightness of the physical LEDs without affecting the accuracy of the representation in the emulator and without the developer having to adjust the value when switching between the emulator and physical LEDs.

  • delay() should always be called in the animation loop, typically after each call to pixels.show(). A delay of 20ms corresponds to a maximum refresh rate of 50Hz (1 / 0.02) and is typically a good value to start with. Refreshing the LEDs more often (delay value lower than 20ms) will probably not cause animations to look any smoother. To speed up the animation it's probably better to increase the step size than the refresh rate.

  • The emulator does not take into account that code runs more slowly on the device than on the PC. On the PC, virtually all the time will be spent in delay() calls but on the device, a non-significant portion of time is typically spent executing the program. The difference causes the sketch to run faster on the PC. The possible difference becomes larger the shorter the delay() is.

Troubleshooting

If the sketch works in the emulator but not on the device, some possible reasons are:

  • The NEOPIXEL_PIN value is ignored by the emulator but determines which pin on the MCU is used for communicating with the physical LEDs. It must be set to the pin to which the LEDs are connected.

  • The supported MCUs are memory limited, some severely so. For instance, the Atmel ATtiny85 has only 512 bytes of RAM. When controlling 60 LEDs with the ATtiny85 (with the LED RGB values alone taking up 180 bytes (3 * 60)), the included sketches use almost all available memory. Adding more functionality without removing something will typically cause them to run out of memory and crash on the device. There's no practical limit to how much memory the sketch can use when running on the PC.

  • If the colors are different between emulator and device, try changing the color channel ordering in the NeoPixel driver object instantiation. Possibilities are NEO_RGB, NEO_GRB and NEO_BRG.

  • When compiling for the PC, the size of int is 32-bit (on both 32- and 64-bit CPUs and OSes). When compiling for the Atmel AVR processor architecture, it's 16-bit. This causes int types and expressions where types are implicitly promoted to int to be much more likely to overflow on the MCU. For instance, uint8_t a = 100; uint32_t b = a * 1000; will give the correct result of b = 100,000 on the PC but a truncated result of b = 31,072 on the MCU, even though a 32-bit int is used for holding the result on both platforms. This happens because, before taking part in an arithmetic operation, both operands must be of the same size and the result is calculated using that size. If the operands are not of the same size, they're promoted to the size of the largest operand or to int if the largest operand is smaller than int. In this example, the literal 1000 is implicitly int, so a is promoted to int. The multiplication is then performed using the resolution of int. On the PC, the result of the operation fits in a 32-bit int and is then directly stored in b. On the MCU, the result does not fit in a 16-bit int, causing an overflow. The truncated result is then expanded to 32-bits and stored in b. The fix for this is to make sure that at least one of the operands is the same size or larger than the size required for holding the result. In the example, this can be done by specifying 1000 as a 32-bit int by appending UL to the number or by casting one of the operands to 32-bit.

    The compiler breaks expressions involving multiple operands into subexpressions and the rules above apply to each subexpression. For instance, uint32_t a = 50; uint8_t b = 100; uint32_t c = a + b * 1000; will, on a machine with 16-bit int, overflow in the b * 1000 subexpression even though a is a 32-bit int. First, b is promoted to int and the multiplication is performed with int resolution, yielding a truncated int result. Then the truncated result is promoted to 32-bit to match a, then added to a, yielding a 32-bit result which is stored directly in c.

makeheaders

The main difference between an Arduino sketch and a regular .cpp file is that sketches have automatically generated prototypes. We use makeheaders for this task. As BSD licensed code can be included in MIT licensed projects, makeheaders.c is included directly in this project.

About

Speed up development for WS2812B / Adafruit NeoPixel RGB LEDs

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages