[CI] Format code according to conventions

platforms/arm_atsam/bootloaders/md_boot.c

@@ -22,8 +22,8 @@
 // WARNING: These are only for CTRL bootloader release "v2.18Jun 22 2018 17:28:08" for bootloader_jump support
 extern uint32_t _eram;
 
-#define BOOTLOADER_MAGIC 0x3B9ACA00
-#define MAGIC_ADDR (uint32_t *)((intptr_t)(&_eram) - 4)
+#    define BOOTLOADER_MAGIC 0x3B9ACA00
+#    define MAGIC_ADDR (uint32_t *)((intptr_t)(&_eram) - 4)
 
 // CTRL keyboards released with bootloader version below must use RAM method. Otherwise use WDT method.
 void bootloader_jump(void) {
@@ -40,7 +40,8 @@ void bootloader_jump(void) {
         *MAGIC_ADDR = BOOTLOADER_MAGIC;  // Set magic number into RAM
         NVIC_SystemReset();              // Perform system reset
 
-        while (1);  // Won't get here
+        while (1)
+            ;  // Won't get here
     }
 }
 
@@ -50,17 +51,22 @@ void bootloader_jump(void) {
 void bootloader_jump(void) {
     WDT->CTRLA.bit.ENABLE = 0;
 
-    while (WDT->SYNCBUSY.bit.ENABLE);
-    while (WDT->CTRLA.bit.ENABLE);
+    while (WDT->SYNCBUSY.bit.ENABLE)
+        ;
+    while (WDT->CTRLA.bit.ENABLE)
+        ;
 
     WDT->CONFIG.bit.WINDOW   = 0;
     WDT->CONFIG.bit.PER      = 0;
     WDT->EWCTRL.bit.EWOFFSET = 0;
     WDT->CTRLA.bit.ENABLE    = 1;
 
-    while (WDT->SYNCBUSY.bit.ENABLE);
-    while (!WDT->CTRLA.bit.ENABLE);
+    while (WDT->SYNCBUSY.bit.ENABLE)
+        ;
+    while (!WDT->CTRLA.bit.ENABLE)
+        ;
 
-    while (1);  // Wait on timeout
+    while (1)
+        ;  // Wait on timeout
 }
 #endif

platforms/avr/bootloaders/bootloadhid.c

@@ -19,8 +19,7 @@
 #include <avr/eeprom.h>
 #include <avr/wdt.h>
 
-__attribute__((weak))
-void bootloader_jump(void) {
+__attribute__((weak)) void bootloader_jump(void) {
     // force bootloadHID to stay in bootloader mode, so that it waits
     // for a new firmware to be flashed
     // NOTE: this byte is part of QMK's "magic number" - changing it causes the EEPROM to be re-initialized

platforms/avr/bootloaders/caterina.c

@@ -18,8 +18,7 @@
 
 #include <avr/wdt.h>
 
-__attribute__((weak))
-void bootloader_jump(void) {
+__attribute__((weak)) void bootloader_jump(void) {
     // this block may be optional
     // TODO: figure it out
 
@@ -35,5 +34,6 @@ void bootloader_jump(void) {
     wdt_enable(WDTO_60MS);
 
     // wait for watchdog timer to trigger
-    while (1) { }
+    while (1) {
+    }
 }

platforms/avr/bootloaders/dfu.c

@@ -28,8 +28,7 @@
 #define BOOTLOADER_RESET_KEY 0xB007B007
 uint32_t reset_key __attribute__((section(".noinit,\"aw\",@nobits;")));
 
-__attribute__((weak))
-void bootloader_jump(void) {
+__attribute__((weak)) void bootloader_jump(void) {
     UDCON  = 1;
     USBCON = (1 << FRZCLK);  // disable USB
     UCSR1B = 0;

platforms/avr/bootloaders/halfkay.c

@@ -19,8 +19,7 @@
 #include <avr/interrupt.h>
 #include <util/delay.h>
 
-__attribute__((weak))
-void bootloader_jump(void) {
+__attribute__((weak)) void bootloader_jump(void) {
     // http://www.pjrc.com/teensy/jump_to_bootloader.html
 
     cli();

platforms/avr/bootloaders/none.c

@@ -16,5 +16,4 @@
 
 #include "bootloader.h"
 
-__attribute__((weak))
-void bootloader_jump(void) { }
+__attribute__((weak)) void bootloader_jump(void) {}

platforms/avr/bootloaders/usbasploader.c

@@ -26,8 +26,7 @@
 #    endif
 #endif
 
-__attribute__((weak))
-void bootloader_jump(void) {
+__attribute__((weak)) void bootloader_jump(void) {
     // Taken with permission of Stephan Baerwolf from https://github.com/tinyusbboard/API/blob/master/apipage.c
 
     wdt_enable(WDTO_15MS);

platforms/chibios/bootloaders/gd32v_dfu.c

@@ -24,8 +24,7 @@
 __IO uint32_t *DBGMCU_KEY = (uint32_t *)DBGMCU_BASE + 0x0CU;
 __IO uint32_t *DBGMCU_CMD = (uint32_t *)DBGMCU_BASE + 0x08U;
 
-__attribute__((weak))
-void bootloader_jump(void) {
+__attribute__((weak)) void bootloader_jump(void) {
     /* The MTIMER unit of the GD32VF103 doesn't have the MSFRST
      * register to generate a software reset request.
      * BUT instead two undocumented registers in the debug peripheral
@@ -37,4 +36,4 @@ void bootloader_jump(void) {
 }
 
 /* Jumping to bootloader is not possible from user code. */
-void enter_bootloader_mode_if_requested(void) { }
+void enter_bootloader_mode_if_requested(void) {}

platforms/chibios/bootloaders/halfkay.c

@@ -19,8 +19,7 @@
 #include <ch.h>
 #include "wait.h"
 
-__attribute__((weak))
-void bootloader_jump(void) {
+__attribute__((weak)) void bootloader_jump(void) {
     wait_ms(100);
     __BKPT(0);
 }

platforms/chibios/bootloaders/kiibohd.c

@@ -23,8 +23,7 @@
 
 const uint8_t sys_reset_to_loader_magic[] = "\xff\x00\x7fRESET TO LOADER\x7f\x00\xff\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00";
 
-__attribute__((weak))
-void bootloader_jump(void) {
+__attribute__((weak)) void bootloader_jump(void) {
     void *volatile vbat = (void *)VBAT;
     __builtin_memcpy(vbat, (const void *)sys_reset_to_loader_magic, sizeof(sys_reset_to_loader_magic));
 

platforms/chibios/bootloaders/none.c

@@ -16,5 +16,4 @@
 
 #include "bootloader.h"
 
-__attribute__((weak))
-void bootloader_jump(void) { }
+__attribute__((weak)) void bootloader_jump(void) {}

platforms/chibios/bootloaders/stm32_dfu.c

@@ -41,8 +41,7 @@ extern uint32_t __ram0_end__;
 #        define STM32_BOOTLOADER_DUAL_BANK_DELAY 100000
 #    endif
 
-__attribute__((weak))
-void bootloader_jump(void) {
+__attribute__((weak)) void bootloader_jump(void) {
     // For STM32 MCUs with dual-bank flash, and we're incapable of jumping to the bootloader. The first valid flash
     // bank is executed unconditionally after a reset, so it doesn't enter DFU unless BOOT0 is high. Instead, we do
     // it with hardware...in this case, we pull a GPIO high/low depending on the configuration, connects 3.3V to
@@ -63,17 +62,16 @@ void bootloader_jump(void) {
 }
 
 // not needed at all, but if anybody attempts to invoke it....
-void enter_bootloader_mode_if_requested(void) { }
+void enter_bootloader_mode_if_requested(void) {}
 
 #else
 
 /* This code should be checked whether it runs correctly on platforms */
-#define SYMVAL(sym) (uint32_t)(((uint8_t *)&(sym)) - ((uint8_t *)0))
-#define BOOTLOADER_MAGIC 0xDEADBEEF
-#define MAGIC_ADDR (unsigned long *)(SYMVAL(__ram0_end__) - 4)
+#    define SYMVAL(sym) (uint32_t)(((uint8_t *)&(sym)) - ((uint8_t *)0))
+#    define BOOTLOADER_MAGIC 0xDEADBEEF
+#    define MAGIC_ADDR (unsigned long *)(SYMVAL(__ram0_end__) - 4)
 
-__attribute__((weak))
-void bootloader_jump(void) {
+__attribute__((weak)) void bootloader_jump(void) {
     *MAGIC_ADDR = BOOTLOADER_MAGIC;  // set magic flag => reset handler will jump into boot loader
     NVIC_SystemReset();
 }

platforms/chibios/bootloaders/stm32duino.c

@@ -18,7 +18,4 @@
 
 #include <ch.h>
 
-__attribute__((weak))
-void bootloader_jump(void) {
-    NVIC_SystemReset();
-}
+__attribute__((weak)) void bootloader_jump(void) { NVIC_SystemReset(); }

platforms/chibios/bootloaders/tinyuf2.c

@@ -25,11 +25,10 @@
 extern uint32_t _board_dfu_dbl_tap[];
 #define DBL_TAP_REG _board_dfu_dbl_tap[0]
 
-__attribute__((weak))
-void bootloader_jump(void) {
+__attribute__((weak)) void bootloader_jump(void) {
     DBL_TAP_REG = DBL_TAP_MAGIC;
     NVIC_SystemReset();
 }
 
 /* not needed, no two-stage reset */
-void enter_bootloader_mode_if_requested(void) { }
+void enter_bootloader_mode_if_requested(void) {}

platforms/test/bootloaders/none.c

@@ -16,4 +16,4 @@
 
 #include "bootloader.h"
 
-void bootloader_jump(void) { }
+void bootloader_jump(void) {}