Remove arm_atsam platform (#24337)

qmk · Sep 2, 2024 · 3bd303f · 3bd303f
1 parent 096aca6
commit 3bd303f
Show file tree

Hide file tree

Showing 215 changed files with 3 additions and 73,516 deletions.
diff --git a/Doxyfile b/Doxyfile
@@ -145,7 +145,7 @@ FILE_PATTERNS          = *.c \
 RECURSIVE              = YES
 EXCLUDE                =
 EXCLUDE_SYMLINKS       = NO
-EXCLUDE_PATTERNS       = */protocol/arm_atsam/*
+EXCLUDE_PATTERNS       =
 EXCLUDE_SYMBOLS        =
 EXAMPLE_PATH           =
 EXAMPLE_PATTERNS       = *

diff --git a/builddefs/common_features.mk b/builddefs/common_features.mk
@@ -238,10 +238,6 @@ else
         OPT_DEFS += -DEEPROM_DRIVER -DEEPROM_TRANSIENT
         SRC += eeprom_driver.c eeprom_transient.c
       endif
-    else ifeq ($(PLATFORM),ARM_ATSAM)
-      # arm_atsam EEPROM
-      OPT_DEFS += -DEEPROM_SAMD
-      SRC += eeprom_samd.c
     else ifeq ($(PLATFORM),TEST)
       # Test harness "EEPROM"
       OPT_DEFS += -DEEPROM_TEST_HARNESS

diff --git a/builddefs/common_rules.mk b/builddefs/common_rules.mk
@@ -58,10 +58,6 @@ endif
 #---------------- C Compiler Options ----------------
 
 ifeq ($(strip $(LTO_ENABLE)), yes)
-    ifeq ($(PLATFORM),ARM_ATSAM)
-        $(info Enabling LTO on arm_atsam-targeting boards is known to have a high likelihood of failure.)
-        $(info If unsure, set LTO_ENABLE = no.)
-    endif
     CDEFS += -flto
     CDEFS += -DLTO_ENABLE
 endif

diff --git a/docs/compatible_microcontrollers.md b/docs/compatible_microcontrollers.md
@@ -75,10 +75,6 @@ You can also use any ARM chip with USB that [ChibiOS](https://www.chibios.org) s
 
 For a detailed overview about the RP2040 support by QMK see the [dedicated RP2040 page](platformdev_rp2040).
 
-## Atmel ATSAM
-
-There is limited support for one of Atmel's ATSAM microcontrollers, that being the [ATSAMD51J18A](https://www.microchip.com/wwwproducts/en/ATSAMD51J18A) used by the [Massdrop keyboards](https://github.com/qmk/qmk_firmware/tree/master/keyboards/massdrop). However, it is not recommended to design a board with this microcontroller as the support is quite specialized to Massdrop hardware.
-
 ## RISC-V
 
 ### GigaDevice

diff --git a/docs/drivers/gpio.md b/docs/drivers/gpio.md
@@ -13,7 +13,7 @@ The following macros provide basic control of GPIOs and are found in `platforms/
 |`gpio_set_pin_input_low(pin)`        |Set pin as input with builtin pull-down resistor (unavailable on AVR)|
 |`gpio_set_pin_output(pin)`           |Set pin as output (alias of `gpio_set_pin_output_push_pull`)         |
 |`gpio_set_pin_output_push_pull(pin)` |Set pin as output, push/pull mode                                    |
-|`gpio_set_pin_output_open_drain(pin)`|Set pin as output, open-drain mode (unavailable on AVR and ATSAM)    |
+|`gpio_set_pin_output_open_drain(pin)`|Set pin as output, open-drain mode (unavailable on AVR)              |
 |`gpio_write_pin_high(pin)`           |Set pin level as high, assuming it is an output                      |
 |`gpio_write_pin_low(pin)`            |Set pin level as low, assuming it is an output                       |
 |`gpio_write_pin(pin, level)`         |Set pin level, assuming it is an output                              |

diff --git a/keyboards/massdrop/alt/alt.c b/keyboards/massdrop/alt/alt.c
diff --git a/keyboards/massdrop/alt/alt.h b/keyboards/massdrop/alt/alt.h
diff --git a/keyboards/massdrop/alt/config.h b/keyboards/massdrop/alt/config.h
diff --git a/keyboards/massdrop/alt/config_led.c b/keyboards/massdrop/alt/config_led.c