Merge pull request #9 from tmk/master

updating

converter/m0110_usb/Makefile

@@ -17,18 +17,16 @@ SRC =	matrix.c \
 ifdef KEYMAP
     SRC += keymap_$(KEYMAP).c
 else
-    SRC += keymap_plain.c
+    SRC += keymap_default.c
 endif
 
 CONFIG_H = config.h
 
 
 # MCU name, you MUST set this to match the board you are using
 # type "make clean" after changing this, so all files will be rebuilt
-#MCU = at90usb162       # Teensy 1.0
-MCU = atmega32u4       # Teensy 2.0
-#MCU = at90usb646       # Teensy++ 1.0
-#MCU = at90usb1286      # Teensy++ 2.0
+MCU = atmega32u2       # TMK converter rev2
+#MCU = atmega32u4       # TMK converter rev1
 
 
 # Processor frequency.

converter/m0110_usb/Makefile.teensy

@@ -0,0 +1,98 @@
+# Target file name (without extension).
+TARGET = m0110_lufa
+
+# Directory common source filess exist
+TOP_DIR = ../..
+
+# Directory keyboard dependent files exist
+TARGET_DIR = .
+
+# keyboard dependent files
+SRC =	matrix.c \
+	led.c \
+	keymap_common.c \
+	m0110.c
+
+# To use own keymap file run make like: make keymap=hasu
+ifdef KEYMAP
+    SRC += keymap_$(KEYMAP).c
+else
+    SRC += keymap_default.c
+endif
+
+CONFIG_H = config.h
+
+
+# MCU name, you MUST set this to match the board you are using
+# type "make clean" after changing this, so all files will be rebuilt
+#MCU = at90usb162       # Teensy 1.0
+MCU = atmega32u4       # Teensy 2.0
+#MCU = at90usb646       # Teensy++ 1.0
+#MCU = at90usb1286      # Teensy++ 2.0
+
+
+# Processor frequency.
+#   Normally the first thing your program should do is set the clock prescaler,
+#   so your program will run at the correct speed.  You should also set this
+#   variable to same clock speed.  The _delay_ms() macro uses this, and many
+#   examples use this variable to calculate timings.  Do not add a "UL" here.
+F_CPU = 16000000
+
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+#     This will define a symbol, F_USB, in all source code files equal to the
+#     input clock frequency (before any prescaling is performed) in Hz. This value may
+#     differ from F_CPU if prescaling is used on the latter, and is required as the
+#     raw input clock is fed directly to the PLL sections of the AVR for high speed
+#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+#     at the end, this will be done automatically to create a 32-bit value in your
+#     source code.
+#
+#     If no clock division is performed on the input clock inside the AVR (via the
+#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+
+# Boot Section Size in bytes
+#   Teensy halfKay   512
+#   Atmel DFU loader 4096
+#   LUFA bootloader  4096
+OPT_DEFS += -DBOOTLOADER_SIZE=512
+
+
+# Build Options
+#   *Comment out* to disable the options.
+#
+#BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
+CONSOLE_ENABLE = yes	# Console for debug(+400)
+COMMAND_ENABLE = yes    # Commands for debug and configuration
+#SLEEP_LED_ENABLE = yes  # Breathing sleep LED during USB suspend
+#NKRO_ENABLE = yes	# USB Nkey Rollover - not yet supported in LUFA
+#KEYMAP_SECTION_ENABLE = yes	# fixed address keymap for keymap editor
+
+
+
+#---------------- Programming Options --------------------------
+PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
+
+
+# Search Path
+VPATH += $(TARGET_DIR)
+VPATH += $(TOP_DIR)
+
+
+include $(TOP_DIR)/protocol/lufa.mk
+include $(TOP_DIR)/protocol.mk
+include $(TOP_DIR)/common.mk
+include $(TOP_DIR)/rules.mk

converter/m0110_usb/README.md

@@ -1,6 +1,6 @@
 M0110/M0110A to USB keyboard converter
 ======================================
-This firmware converts the protocol of Apple Macintosh keyboard **M0110**, **M0110A** and **M0120** into USB. Target of this project is USB AVR controller **ATmega32U4**. Using this converter you can revive these retro keyboards with modern computer.
+This firmware converts the protocol of Apple Macintosh keyboard **M0110**, **M0110A** and **M0120** into USB. Target of this project is USB AVR controller like **ATmega32U2** and **ATmega32U4**. Using this converter you can revive these retro keyboards with modern computer.
 
 Read README of top directory too.
 
@@ -20,12 +20,13 @@ Update
 - 2013/08: Change port for signals `PF` to `PD`
 - 2013/09: Change port again, it uses inversely `PD0` for data and `PD1` for clock line now.
 - 2014/06: Change keymaps
+- 2015/03: Add support for "International"(ISO) keyboard(keymap_intl.c)
 
 
 
 Building Hardware
 -----------------
-You need **4P4C** cable and **ATMega32U4** board like PJRC [Teensy]. Port of the MCU `PD1` is assigned to `CLOCK` line and `PD0` to `DATA` by default, you can change pin configuration with editing `config.h`.
+You need [TMK converter] or AVR dev board like PJRC [Teensy]. Port of the MCU `PD1` is assigned to `CLOCK` line and `PD0` to `DATA` by default, you can change pin configuration with editing `config.h`.
 
 [![M0110 Converter](http://i.imgur.com/4G2ZOegm.jpg)](http://i.imgur.com/4G2ZOeg.jpg)
 
@@ -38,6 +39,7 @@ Close-up picture of handset cable. You can see one end of plug has reverse color
 [![4P4C cable](http://i.imgur.com/3S9P1mYm.jpg?1)](http://i.imgur.com/3S9P1mY.jpg?1)
 
 [Teensy]: http://www.pjrc.com/teensy/
+[TMK converter]: https://github.com/tmk/keyboard_converter
 
 
 ### Socket Pinout
@@ -53,31 +55,28 @@ You may need pull-up resistors on signal lines(`CLOCK`, `DATA`) in particular wh
 
 Building Firmware
 -----------------
-To compile firmware you need AVR GCC. You can edit *Makefile* and *config.h* to change compile options and pin configuration.
+To compile firmware you need AVR GCC. You can edit *Makefile* and *config.h* to change compile options and pin configuration. Also `KEYMAP` option can be used to select keymap.
 
     $ git clone git://github.com/tmk/tmk_keyboard.git (or download source)
     $ cd m0110_usb
-    $ make clean
-    $ make
+    $ make -f Makefile clean
+    $ make -f Makefile [KEYMAP={default|plain|intl|spacefn|hasu}]
 
-To select keymap use `KEYMAP` option.
-
-    $ make clean
-    $ make KEYMAP={plain|spacefn|hasu}
+Use `Makefile.teensy` instead for Teensy.
 
 
 
 Keymap
 ------
 To create your own keymap copy existent keymap file to `keymap_name.c` and edit it. You can build it like this.
 
-    $ make clean
-    $ make KEYMAP=name
+    $ make -f Makefile clean
+    $ make -f Makefile KEYMAP=name
 
 
 
 Debug
 -----
-You can use [PJRC HID listen](http://www.pjrc.com/teensy/hid_listen.html) to see debug output. The converter has some functions for debug, press `<Command>+H` simultaneously to get help.
+You can use [PJRC HID listen](http://www.pjrc.com/teensy/hid_listen.html) to see debug output. The converter has some functions for debug, press `<Magic>+H` simultaneously to get help.
 
-- Command: `Shift+Option+Command`(`Shift+Alt+Gui` or `Shift+Alt+Control`)
+- Magic combo: `Shift+Option+⌘` or `Shift+Option+Ctrl`(`Shift+Alt+Gui` or `Shift+Alt+Control`)