Restyled by prettier-markdown

docs/guides/chip_tool_guide.md

@@ -257,15 +257,15 @@ Alternatively, you can also use a QR code payload.
 
 ##### Commissioning with setup PIN code
 
-To discover devices and try to pair with the first available discovered device using the
-provided setup code, use the following command pattern:
+To discover devices and try to pair with the first available discovered device
+using the provided setup code, use the following command pattern:
 
 ```
 $ ./chip-tool pairing onnetwork <node_id> <pin_code>
 ```
 
-The command keeps trying devices until pairing with one of them succeeds or until it runs out of pairing possibilities.
-In this command:
+The command keeps trying devices until pairing with one of them succeeds or
+until it runs out of pairing possibilities. In this command:
 
 -   _<node_id\>_ is the user-defined ID of the node being commissioned.
 -   _<pin_code\>_ is device specific _setup PIN code_ determined in the
@@ -274,15 +274,16 @@ In this command:
 
 ##### Commissioning with long discriminator
 
-To discover devices with a long discriminator and try to pair with the first available discovered device
-using the provided setup code, use the following command pattern:
+To discover devices with a long discriminator and try to pair with the first
+available discovered device using the provided setup code, use the following
+command pattern:
 
 ```
 $ ./chip-tool pairing onnetwork-long <node_id> <pin_code> <discriminator>
 ```
 
-The command keeps trying devices until pairing with one of them succeeds or until it runs out of pairing possibilities.
-In this command:
+The command keeps trying devices until pairing with one of them succeeds or
+until it runs out of pairing possibilities. In this command:
 
 -   _<node_id\>_ is the user-defined ID of the node being commissioned.
 -   _<pin_code\>_ and _<discriminator\>_ are device specific keys determined in
@@ -294,15 +295,15 @@ In this command:
 Matter devices log the QR code payload and manual pairing code when they boot.
 
 To discover devices based on the given QR code payload or manual pairing code
-and try to pair with the first available discovered device, use the following command
-pattern:
+and try to pair with the first available discovered device, use the following
+command pattern:
 
 ```
 $ ./chip-tool pairing code <node_id> <qrcode_payload-or-manual_code>
 ```
 
-The command keeps trying devices until pairing with one of them succeeds or until it runs out of pairing possibilities.
-In this command:
+The command keeps trying devices until pairing with one of them succeeds or
+until it runs out of pairing possibilities. In this command:
 
 -   _<node_id\>_ is the user-defined ID of the node being commissioned.
 -   _<qrcode_payload-or-manual_code\>_ is the QR code payload ID, for example
@@ -413,12 +414,14 @@ The CHIP Tool can run in one of the following modes:
     [1650992689511] [32397:1415601] CHIP: [TOO] Run command failure: ../../../examples/chip-tool/commands/common/CHIPCommand.cpp:392: CHIP Error 0x00000032: Timeout
     ```
 
-    Moreover, when using the single-command mode, the CHIP Tool will establish a new CASE session with every command sent (and close the existing one).
+    Moreover, when using the single-command mode, the CHIP Tool will establish a
+    new CASE session with every command sent (and close the existing one).
+
 -   Interactive mode - In this mode, a command will terminate with an error if
     it does not complete within the timeout period. However, the CHIP Tool will
     not be terminated and it will not terminate processes that previous commands
-    have started.
-    Moreover, when using the interactive mode, the CHIP Tool will establish a CASE session only on the first command sent.
+    have started. Moreover, when using the interactive mode, the CHIP Tool will
+    establish a CASE session only on the first command sent.
 
 #### Modifying timeout duration in single-command mode