Reloop Jockey 3 Me

Reloop Jockey 3 Master Edition

The Reloop Jockey 3 Master Edition is a 2 Channel Controller with the option to control 4 Channels. It is Designed for Traktor Pro 1. This is a Documentation to use this Controller with Mixxx.

Setup

The Mixxx mapping uses the same settings as Reloop's Traktor mapping. Leave the MIDI channels as the default 1-4. If you have problems with the jogwheels, set the jogwheel resolution to 2048. (Please read the manual of this Controller section 5.1 and 5.1.2)

Set the Input 1 and Input 2 switches on the front side of the Jockey 3 ME to SW.

Mixxx Sound Hardware Preferences

Master output: channels 1-2
Headphone output: channels 3-4
Auxiliary or vinyl input 1: channels 1-2
Auxiliary or vinyl input 2: channels 3-4
Microphone input: channels 5-6

Mapping Guide

Mixer Section

Trax encoder: scroll through library. With shift, scroll through sections on the left side of the library. Push to toggle big library.
Load button: load selected track into active deck
Deck switches: select between controlling deck 1/3 or analog input 1 on the left; select between controlling deck 2/4 or analog input 2 on the right. Note that the analog inputs are only affected by the mixer controls but not the other deck controls.
Gain: set deck gain
High/mid/low: adjust EQ for high/mid/low frequencies
Master/booth/phones: control the Jockey 3 ME's sound card. These knobs do not send MIDI messages or adjust values in Mixxx, so turning them will not change anything on screen. Use these but not the software knobs on screen in Mixxx (see the Mixxx manual for an explanation).
Headphones: play deck on headphone output
Cuemix: Fade between PFL and master output on headphones
Vertical faders: deck volume
Level meter LEDs: show the level of the deck
Crossfader: fade between decks
Crossfader curve (front side of controller): Adjust crossfader curve between fade and cut.

Transport Section

Play/pause: play/pause or, with shift, toggle keylock
Cue: behavior depends on cue mode set in Mixxx preferences
Cup: Like Cue, but it plays only after releasing the button.
Sync: toggle master sync

Jogwheels

Scratch mode: If Active, you can Scratch the current loadet file in this Deck. If you touch the oudside Rubber ring, you can push or pull the speed of a playing file.
Nudging mode: Not Mapped. FIXME (No plans)
Search mode: Not Mapped. FIXME (In future planed)
Note mode: Not Mapped. FIXME (Plan to Control the SuperKnop on the EffectChain of the Deck)

Pitch Fader

Sets a new speedrate of the playing Deck.

Hotcue Section

Press an unlit hotcue button to set that hotcue at the current position. Press a lit hotcue button to jump to that hotcue. To delete a hotcue, hold the Trash button while pressing a hotcue. To toggle between hotcues 1-4 and 5-8, press the 5-8 button.

Loop Section

Length encoder: Press to activate a 4 beat loop. Double or half the beats of the loop by turning
Move encoder: Move a track 4 Beats forward or backward.
Loop button: ??? FIXME. With shift, sets the start position of a loop.
Reloop button: does not work as labeled; toggles quantize. With shift, sets the end position of a loop.

Other controls

Filter: turn to apply a highpass or lowpass filter. On Deck A, press Shift and turn Filter to adjust the Gain of the Microphone
Pan: On Deck A, turn to fade between the left and right speakers on the master output. (Balance)
< Beat: does not function as labeled. It aligns the beatgrid with the current play position. With shift, moves the beatgrid lines further from each other (lower BPM by 0.01)
Beat >: Not as intended it do Microphone Talkover. With shift, moves beatgrid lines closer to each other (raise BPM by 0.01)

Effect Section

The effect section controls the effect chain with the same number as the deck selected by the deck switch, although any effect chain can be applied to any deck.

Dry/wet: adjust how much the effect is applied. With shift, turn to select different effect chain presets
FX Param: adjust effect parameters 1-3 for the first effect in the chain. FIXME: With shift, select different effects in chain. Push to link effect parameter to superknob
FX on: enable/disable effect chain
Preset 1-4 (shift+effect buttons): apply effect chain to that deck number

Mixxx This is the Mixxx Wiki - Wiki Home | Website | Manual | News