Behringer Cmd Mm 1

Behringer CMD MM-1

• Forum thread

The Behringer CMD MM-1 is a flexible controller that controls 4 decks by default. The mapping can be easily configured to control any combination of decks and effect units. The Behringer CMD DC-1 and Behringer CMD DV-1 are designed to be used together with the CMD MM-1, but the CMD MM-1 can be used alone or with other controllers (especially the Novation Launchpad)

All following examples will be made with a help of a 3D model.

This demonstration video shows how the mapping works by default with every channel in Deck mode: (Outdated)

Mapping description

Mapping options

There are a few user configurable options available for you to customize. You can change these by opening the Behringer-CMD-MM-1-scripts.js file in your controller mapping file locations#user controller mapping folder with your text editor of choice (such as Notepad, TextEdit, Kate, or gEdit) and editing the lines at the very top of the file.

• channelNumber: change this if your #controller does not light up
• invertColor: Swaps the colors which suits certain skins more
• defaultChannelSequence: Defines how the channels are mapped when Mixxx starts
• channelMode: Defines if a channel is in Deck or FX Mode when Mixxx starts
• standardKnobBehavior: Defines the mapping of the knobs when Mixxx starts

Top row

The top left knobs control the Master balance and Master gain. The top right knobs control the headphone gain and cue mix (PFL/master mix in Headphones output).

You can see the L/R buttons besides the encoder as [SHIFT] and [CTRL] buttons. These allow each button to have up to four functionalities. They behave like the Shift and Control keys on a computer keyboard. Most of the features can be explained via the renderings where the functionalities are marked by the formatting of the Text ([SHIFT] and [CTRL]).

The encoder in the middle is able to browse the library and jump on the preview deck (16 steps) while holding shift. When pressing the encoder, the selected/highlighted track in the library gets loaded into the preview deck. The preview deck can be played/paused when holding shift while pressing the encoder down.

Knobs

The Knobs have three different modes which can be cycled while in operation. The knobs in each mode, from top to bottom, control:

1. Deck: High, Mid, Low, QuickEffect (filter by default)
2. Deck: Gain, High, Mid, Low
3. Effect Unit: Meta 1, Meta 2, Meta 3, Mix

The Effect Unit number is the same as the channel/deck number, so the channel that controls the knobs/buttons/faders of deck 1 also controls the knobs of EffectUnit1, Channel 2 controls EffectUnit2, and so on.

FX Mode

The Knobs in FxMode overwrite the assigned mapping and are mapped as [Effect 1 Meta, Effect 2 Meta, Effect 3 Meta, Super] and the fader is also mapped to the mix of the EffectUnit. The buttons are documented in their own section.

Middle button

• Normal: toggle maximize library
• Shift: recenter Crossfader
• Ctrl: Cycle Knob assignment (swaps the mapping of the knobs as mentioned earlier.
• Third: Reassing Channel Sequence (resets mapping back do the global defaults (look at global vars))

Buttons

Deck Mode

[1]&[2] Buttons:

• Normal: Change Crossfader side (Orientation)
• Shift: Toggle Fx1&2 for desired Channel
• Ctrl: Toggle Fx3&4 for desired Channel
• Third: Change ChannelNumber/Assignment

[CUE] Buttons:

• Normal: Pre-Fader-Listening
• Shift: Load selected Track to Deck
• Ctrl: Enable Fx-PFL for Unit according to channel number.
• Third: Change Channelmode

FX Mode

[1]&[2] Buttons:

• Normal: Toggle Effect 1&2 in desired FxUnit
• Shift: Toggle Channel1&2 for desired FxUnit
• Ctrl: Toggle Channel3&4 for desired FxUnit
• Third: Change ChannelNumber/Assignment

[CUE] Buttons:

• Normal: Toggle Effect 3 for desired FxUnit
• Shift: Pre-Fader-Listening for FxUnit
• Ctrl: assign to master
• Third: Change Channelmode

Faders

DeckMode:

• Normal: Volume Fader
• Shift: Rate-/BPM-Faders

FxMode:

• EffectUnit Mix (dry/wet)

Reassigning channel mode and number

The channel modes and numbers can be set by changing the #mapping options at the top of the script. They can also be changed while using the controller when in thirdMode. Pressing the cue- button toggles between Deck and FX Mode. The Channel number is assigned with the [1]&[2] buttons.

They are mapped in a sort of two bit encoded system:

• & [ ] = Channel 1
• & [ ] = Channel 2
• & [x] = Channel 3
• & [x] = Channel 4

So you can change between channel 1&3 by pressing the [1] button, and channel 2&4 by pressing the [2] button.

Troubleshooting

Controller does not light up

The issue is probably the MIDI channel of your MM-1. Behringer had a tool that can set the controller to a different MIDI channel, however this is no longer available for download from Behringer's website. So you will have to modify the controller mapping to use the MIDI channel that your controller is set to. Refer to MIDI Crash Course for how to see incoming MIDI messages from your controller.

NOTE: The Behringer Website is currently (07.04.2018) undergoing some update which is why the productpage and the channelswitcher utility is currently unavailable. After Emailing the support, they provided a link to the Channelswitcher (Mirror) and a manual (Mirror) for the whole CMD line up.

Once you know the MIDI channel of your controller, open the file Behringer-CMD-MM-1-scripts.js file in your controller mapping file locations#user controller mapping folder with your text editor of choice (such as Notepad, TextEdit, Kate, or gEdit) and replace the number 5 in the line where it says var CHANNELNUMBER = 5;. Then, open the file Behringer CMD-MM-1.midi.xml in the same folder and replace the 4 at the end of 0x94, 0x84 and 0xB4 with your CHANNEL-NUMBER MINUS 1. Restart Mixxx, reload the mapping in Mixxx's preferences, and then it should work.