sir am using GTPA010 GPS module with arduino uno am getting character and err but not getting any lat or long

[Punithpeshva]

am using GTPAO10 GPS module with antenna i used your library it will show some values for char and err but not showing any lat or long just shows garbage characters pls help me out

[mikalhart]

Probably a baud rate mismatch? I think GTPAO10 defaults to 9600, but the sample code is 4800.

From: Punithpeshva [mailto:[email protected]]
Sent: Monday, March 16, 2015 7:10 AM
To: mikalhart/TinyGPS
Subject: [TinyGPS] sir am using GTPA010 GPS module with arduino uno am getting character and err but not getting any lat or long (#4)

am using GTPAO10 GPS module with antenna i used your library it will show some values for char and err but not showing any lat or long just shows garbage characters pls help me out

—
Reply to this email directly or view it on GitHub #4 .Image removed by sender.

[Punithpeshva]

I changed it to 9600 but end up with same result :(
On 17 Mar 2015 02:48, "Mikal Hart" [email protected] wrote:

Probably a baud rate mismatch? I think GTPAO10 defaults to 9600, but the
sample code is 4800.

From: Punithpeshva [mailto:[email protected]]
Sent: Monday, March 16, 2015 7:10 AM
To: mikalhart/TinyGPS
Subject: [TinyGPS] sir am using GTPA010 GPS module with arduino uno am
getting character and err but not getting any lat or long (#4)

am using GTPAO10 GPS module with antenna i used your library it will show
some values for char and err but not showing any lat or long just shows
garbage characters pls help me out

—
Reply to this email directly or view it on GitHub <
https://github.com/mikalhart/TinyGPS/issues/4> .Image removed by sender.

—
Reply to this email directly or view it on GitHub
#4 (comment).

[mikalhart]

Please try to Serial.write() each character coming from the GPS, just to make sure you are getting readable data.

From: Punithpeshva [mailto:[email protected]]
Sent: Monday, March 16, 2015 8:55 PM
To: mikalhart/TinyGPS
Cc: Mikal Hart
Subject: Re: [TinyGPS] sir am using GTPA010 GPS module with arduino uno am getting character and err but not getting any lat or long (#4)

I changed it to 9600 but end up with same result :(
On 17 Mar 2015 02:48, "Mikal Hart" [email protected] wrote:

Probably a baud rate mismatch? I think GTPAO10 defaults to 9600, but the
sample code is 4800.

From: Punithpeshva [mailto:[email protected]]
Sent: Monday, March 16, 2015 7:10 AM
To: mikalhart/TinyGPS
Subject: [TinyGPS] sir am using GTPA010 GPS module with arduino uno am
getting character and err but not getting any lat or long (#4)

am using GTPAO10 GPS module with antenna i used your library it will show
some values for char and err but not showing any lat or long just shows
garbage characters pls help me out

—
Reply to this email directly or view it on GitHub <
https://github.com/mikalhart/TinyGPS/issues/4> .Image removed by sender.

—
Reply to this email directly or view it on GitHub
#4 (comment).

—
Reply to this email directly or view it on GitHub #4 (comment) .Image removed by sender.

[mikalhart]

Make a test loop that just does this:

void loop()

{

if (ss.available() > 0)

  Serial.write(ss.read());

}

Assuming you have all the baud rates correctly set up for ss and Serial, this should print readable characters on the serial monitor.

From: Punithpeshva [mailto:[email protected]]
Sent: Tuesday, March 17, 2015 3:10 AM
To: mikalhart/TinyGPS
Cc: Mikal Hart
Subject: Re: [TinyGPS] sir am using GTPA010 GPS module with arduino uno am getting character and err but not getting any lat or long (#4)

Sorry I didn't get using serial.write where the data will be written I
have used serialprint bt not write sorry that's why asked and thank you so
much for your concern and reply
And one doubt if device is not getting readable data means what's the fault
may be??
On 17 Mar 2015 08:57, "Mikal Hart" [email protected] wrote:

Please try to Serial.write() each character coming from the GPS, just to
make sure you are getting readable data.

From: Punithpeshva [mailto:[email protected]]
Sent: Monday, March 16, 2015 8:55 PM
To: mikalhart/TinyGPS
Cc: Mikal Hart
Subject: Re: [TinyGPS] sir am using GTPA010 GPS module with arduino uno am
getting character and err but not getting any lat or long (#4)

I changed it to 9600 but end up with same result :(
On 17 Mar 2015 02:48, "Mikal Hart" [email protected] wrote:

Probably a baud rate mismatch? I think GTPAO10 defaults to 9600, but the
sample code is 4800.

From: Punithpeshva [mailto:[email protected]]
Sent: Monday, March 16, 2015 7:10 AM
To: mikalhart/TinyGPS
Subject: [TinyGPS] sir am using GTPA010 GPS module with arduino uno am
getting character and err but not getting any lat or long (#4)

am using GTPAO10 GPS module with antenna i used your library it will show
some values for char and err but not showing any lat or long just shows
garbage characters pls help me out

—
Reply to this email directly or view it on GitHub <
https://github.com/mikalhart/TinyGPS/issues/4> .Image removed by sender.

—
Reply to this email directly or view it on GitHub
#4 (comment).

—
Reply to this email directly or view it on GitHub <
https://github.com/mikalhart/TinyGPS/issues/4#issuecomment-82029331>
.Image removed by sender.

—
Reply to this email directly or view it on GitHub
#4 (comment).

—
Reply to this email directly or view it on GitHub #4 (comment) .Image removed by sender.

[Punithpeshva]

when i use serial.Write its just shwoing "9999"