Update README and BOM to rev1.5

BOM.csv

@@ -25,6 +25,7 @@ L2,20n,Inductors_SMD:L_0402,1,TE Connectivity / Sigma Inductors,36501E20NJTDG,Mo
 L1,22n,Inductors_SMD:L_0402,1,Murata Electronics,LQW15CA22NJ00D,Mouser,81-LQW15CA22NJ00D
 L4,27n,Inductors_SMD:L_0402,1,Murata Electronics,LQW15AN27NG80D,Mouser,81-LQW15AN27NG80D
 D7,amber,LEDs:LED_0402,1,Kingbright,APG1005SEC-T,Mouser,604-APG1005SECT
+D9,blue,LEDs:LED_0402,1,Kingbright,APHHS1005QBC/D,Mouser,604-APHHS1005QBCD
 D2;D6,green,LEDs:LED_0402,2,Kingbright,APHHS1005CGCK,Mouser,604-APHHS1005CGCK
 D4;D8;D1,red,LEDs:LED_0402,3,Kingbright,APHHS1005SURCK,Mouser,604-APHHS1005SURCK
 D3;D5,yellow,LEDs:LED_0402,2,Kingbright,APG1005SYC-T,Mouser,604-APG1005SYCT
@@ -33,7 +34,7 @@ P2,DISPLAY,Pin_Headers:Pin_Header_Straight_1x04,1,TE Connectivity / AMP,826629-4
 P1,I2C,Pin_Headers:Pin_Header_Straight_1x04,1,TE Connectivity / AMP,826629-4,Mouser,571-826629-4
 P4,STLINK,Pin_Headers:Pin_Header_Straight_1x04,1,TE Connectivity / AMP,826629-4,Mouser,571-826629-4
 R1;R7,10k,Resistors_SMD:R_0402,2,Vishay,CRCW040210K0FKED,Mouser,71-CRCW0402-10K-E3
-R8;R9;R10;R11;R12;R13;R14;R15;R16;R17;R18,1k,Resistors_SMD:R_0402,11,Panasonic,ERJ-PA2D1001X,Mouser,667-ERJ-PA2D1001X
+R8;R9;R10;R11;R12;R13;R14;R15;R16;R17;R18;R19,1k,Resistors_SMD:R_0402,12,Panasonic,ERJ-PA2D1001X,Mouser,667-ERJ-PA2D1001X
 R2,1k1,Resistors_SMD:R_0402,1,Susumu,RR0510P-112-D,Mouser,754-RR0510P-112D
 R6,270,Resistors_SMD:R_0402,1,Panasonic,ERA-2AEB271X,Mouser,667-ERA-2AEB271X
 R3,3k8,Resistors_SMD:R_0402,1,Susumu,RR0510P-3831-D,Mouser,754-RR0510P-3831D

README.md

@@ -42,12 +42,16 @@ The boot jumper was removed and the STlink header moved to its position. This ga
 ### Revision 1.4
 The SVC LED has been rotated and thus aligned to the layout of all other LEDs. The RainSun ceramic antenna has been replaced by a model that can be ordered at Mouser. DC line filtering has been added to 3v3 line.
 
+### Revision 1.5
+A fith mode LED has been added to the board to show NXDN activity. The two pin headers moved downwards a little. The rev1.4 stencil can be re-used if you manually add solder paste to R19 and D9 afterwards.
+
 ## BOM
 * All necessary parts for the Revision 1.1 board can be ordered at Mouser using the following [shopping cart](http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=780b8eac44)
 * All necessary parts for the Revision 1.2 board can be ordered at Mouser using the following [shopping cart](http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=035e777242)
 * There is also a light version of revision 1.2 without the reset switch, 2.54mm headers and SMA connector [Link](http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=3f7d0256e1)
 * The parts for Revision 1.3 board are in this [Mouser cart](http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=250d76339b) and the light version is [here](http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=2d533ac53d)
 * [Mouser project](http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=5cab954f40) for MMDVM_HS_Hat revision 1.4
+* There is another [Mouser cart for rev 1.5](https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=5a3e4ae018).
 
 Please note that the onboard ceramic antenna is not supplied by Mouser and therefore missing in the carts for revisions up to 1.3.