change(ble): npl count is zero if nimble host is not used

change(ble): added npl eventq put to front

change(ble): added cache safe check in ble power save example

ble(update):
    Update c2 lib to 91b81332
    Update h2 lib to 620fbe79
    Update c6 lib to 620fbe79

fix(ble): fix stack overflow disable at sleep

Revert "change(ble): added ble cca en and thresh option"

This reverts commit 7190149.

components/bt/controller/esp32c2/Kconfig.in

@@ -464,23 +464,3 @@ config BT_CTRL_BLE_ADV_REPORT_DISCARD_THRSHOLD
 config BT_LE_RELEASE_IRAM_SUPPORTED
     bool
     default y
-
-config BT_LE_TX_CCA_ENABLED
-    bool "BLE enable TX CCA feature"
-    default n
-    help
-        Enable the BLE (Bluetooth Low Energy) LBT (Listen Before Talk) function. Before transmitting a packet,
-        monitor the in-band CCA (Clear Channel Assessment). If the airborne carrier energy is too high, abandon
-        the packet transmission. Enabling this feature may potentially decrease BLE performance. In certain
-        countries and regions, when the maximum transmission power exceeds a certain limit, support for LBT
-        interference avoidance mechanisms is required. If the maximum transmission power does not reach the limit,
-        it may not be necessary to enable this function.
-        Please refer to the relevant certification regulations for details.
-
-config BT_LE_CCA_RSSI_THRESH
-    int "Power threshold to refrain packet transmission in unit of -1 dBm"
-    depends on BT_LE_TX_CCA_ENABLED
-    range 1 100
-    default 75
-    help
-        If a carrier signal above the threshold is detected in the air, refrain from packet transmission.

components/bt/controller/esp32c2/bt.c

@@ -1019,7 +1019,7 @@ void esp_ble_controller_log_dump_all(bool output)
     esp_panic_handler_reconfigure_wdts(5000);
     BT_ASSERT_PRINT("\r\n[DUMP_START:");
     ble_log_async_output_dump_all(output);
-    BT_ASSERT_PRINT("]\r\n");
+    BT_ASSERT_PRINT(":DUMP_END]\r\n");
     portEXIT_CRITICAL_SAFE(&spinlock);
 }
 #endif // CONFIG_BT_LE_CONTROLLER_LOG_ENABLED

components/bt/controller/esp32c6/Kconfig.in

@@ -382,7 +382,7 @@ config BT_LE_WHITELIST_SIZE
 
 config BT_LE_LL_DUP_SCAN_LIST_COUNT
     int "BLE duplicate scan list count"
-    range 1 100
+    range 5 100
     default 20
     help
         config the max count of duplicate scan list
@@ -543,15 +543,6 @@ config BT_LE_SCAN_DUPL_TYPE
     default 2 if BT_LE_SCAN_DUPL_TYPE_DATA_DEVICE
     default 0
 
-config BT_LE_SCAN_DUPL_CACHE_SIZE
-    int "Maximum number of devices in scan duplicate filter"
-    depends on BT_LE_SCAN_DUPL
-    range 10 1000
-    default 100
-    help
-        Maximum number of devices which can be recorded in scan duplicate filter.
-        When the maximum amount of device in the filter is reached, the cache will be refreshed.
-
 config BT_LE_SCAN_DUPL_CACHE_REFRESH_PERIOD
     int "Duplicate scan list refresh period (seconds)"
     depends on BT_LE_SCAN_DUPL
@@ -571,23 +562,3 @@ config BT_LE_SCAN_DUPL_CACHE_REFRESH_PERIOD
 config BT_LE_MSYS_INIT_IN_CONTROLLER
     bool "Msys Mbuf Init in Controller"
     default y
-
-config BT_LE_TX_CCA_ENABLED
-    bool "BLE enable TX CCA feature"
-    default n
-    help
-        Enable the BLE (Bluetooth Low Energy) LBT (Listen Before Talk) function. Before transmitting a packet,
-        monitor the in-band CCA (Clear Channel Assessment). If the airborne carrier energy is too high, abandon
-        the packet transmission. Enabling this feature may potentially decrease BLE performance. In certain
-        countries and regions, when the maximum transmission power exceeds a certain limit, support for LBT
-        interference avoidance mechanisms is required. If the maximum transmission power does not reach the limit,
-        it may not be necessary to enable this function.
-        Please refer to the relevant certification regulations for details.
-
-config BT_LE_CCA_RSSI_THRESH
-    int "Power threshold to refrain packet transmission in unit of -1 dBm"
-    depends on BT_LE_TX_CCA_ENABLED
-    range 1 100
-    default 75
-    help
-        If a carrier signal above the threshold is detected in the air, refrain from packet transmission.

components/bt/controller/esp32c6/bt.c

@@ -665,7 +665,7 @@ void ble_controller_scan_duplicate_config(void)
     uint32_t duplicate_mode = FILTER_DUPLICATE_DEFAULT;
     uint32_t cache_size = 100;
 #if CONFIG_BT_LE_SCAN_DUPL == true
-    cache_size = CONFIG_BT_LE_SCAN_DUPL_CACHE_SIZE;
+    cache_size = CONFIG_BT_LE_LL_DUP_SCAN_LIST_COUNT;
     if (CONFIG_BT_LE_SCAN_DUPL_TYPE == 0) {
         duplicate_mode = FILTER_DUPLICATE_ADDRESS | FILTER_DUPLICATE_PDUTYPE;
     } else if (CONFIG_BT_LE_SCAN_DUPL_TYPE == 1) {
@@ -911,9 +911,9 @@ esp_err_t esp_bt_controller_enable(esp_bt_mode_t mode)
         esp_pm_lock_acquire(s_pm_lock);
 #endif  // CONFIG_PM_ENABLE
         esp_phy_enable(PHY_MODEM_BT);
-        esp_btbb_enable();
         s_ble_active = true;
     }
+    esp_btbb_enable();
 #if CONFIG_SW_COEXIST_ENABLE
     coex_enable();
 #endif // CONFIG_SW_COEXIST_ENABLE
@@ -929,8 +929,8 @@ esp_err_t esp_bt_controller_enable(esp_bt_mode_t mode)
 #if CONFIG_SW_COEXIST_ENABLE
     coex_disable();
 #endif
+    esp_btbb_disable();
     if (s_ble_active) {
-        esp_btbb_disable();
         esp_phy_disable(PHY_MODEM_BT);
 #if CONFIG_PM_ENABLE
         esp_pm_lock_release(s_pm_lock);
@@ -952,8 +952,8 @@ esp_err_t esp_bt_controller_disable(void)
 #if CONFIG_SW_COEXIST_ENABLE
     coex_disable();
 #endif
+    esp_btbb_disable();
     if (s_ble_active) {
-        esp_btbb_disable();
         esp_phy_disable(PHY_MODEM_BT);
 #if CONFIG_PM_ENABLE
         esp_pm_lock_release(s_pm_lock);
@@ -1192,7 +1192,7 @@ void esp_ble_controller_log_dump_all(bool output)
     esp_panic_handler_reconfigure_wdts(5000);
     BT_ASSERT_PRINT("\r\n[DUMP_START:");
     ble_log_async_output_dump_all(output);
-    BT_ASSERT_PRINT("]\r\n");
+    BT_ASSERT_PRINT(":DUMP_END]\r\n");
     portEXIT_CRITICAL_SAFE(&spinlock);
 }
 #endif // CONFIG_BT_LE_CONTROLLER_LOG_ENABLED

components/bt/controller/esp32h2/Kconfig.in

@@ -373,7 +373,7 @@ config BT_LE_WHITELIST_SIZE
 
 config BT_LE_LL_DUP_SCAN_LIST_COUNT
     int "BLE duplicate scan list count"
-    range 1 100
+    range 5 100
     default 20
     help
         config the max count of duplicate scan list
@@ -535,16 +535,6 @@ config BT_LE_SCAN_DUPL_TYPE
     default 2 if BT_LE_SCAN_DUPL_TYPE_DATA_DEVICE
     default 0
 
-
-config BT_LE_SCAN_DUPL_CACHE_SIZE
-    int "Maximum number of devices in scan duplicate filter"
-    depends on BT_LE_SCAN_DUPL
-    range 10 1000
-    default 100
-    help
-        Maximum number of devices which can be recorded in scan duplicate filter.
-        When the maximum amount of device in the filter is reached, the cache will be refreshed.
-
 config BT_LE_SCAN_DUPL_CACHE_REFRESH_PERIOD
     int "Duplicate scan list refresh period (seconds)"
     depends on BT_LE_SCAN_DUPL
@@ -564,23 +554,3 @@ config BT_LE_SCAN_DUPL_CACHE_REFRESH_PERIOD
 config BT_LE_MSYS_INIT_IN_CONTROLLER
     bool
     default y
-
-config BT_LE_TX_CCA_ENABLED
-    bool "BLE enable TX CCA feature"
-    default n
-    help
-        Enable the BLE (Bluetooth Low Energy) LBT (Listen Before Talk) function. Before transmitting a packet,
-        monitor the in-band CCA (Clear Channel Assessment). If the airborne carrier energy is too high, abandon
-        the packet transmission. Enabling this feature may potentially decrease BLE performance. In certain
-        countries and regions, when the maximum transmission power exceeds a certain limit, support for LBT
-        interference avoidance mechanisms is required. If the maximum transmission power does not reach the limit,
-        it may not be necessary to enable this function.
-        Please refer to the relevant certification regulations for details.
-
-config BT_LE_CCA_RSSI_THRESH
-    int "Power threshold to refrain packet transmission in unit of -1 dBm"
-    depends on BT_LE_TX_CCA_ENABLED
-    range 1 100
-    default 75
-    help
-        If a carrier signal above the threshold is detected in the air, refrain from packet transmission.

components/bt/controller/esp32h2/bt.c

@@ -640,7 +640,7 @@ void ble_controller_scan_duplicate_config(void)
     uint32_t duplicate_mode = FILTER_DUPLICATE_DEFAULT;
     uint32_t cache_size = 100;
 #if CONFIG_BT_LE_SCAN_DUPL == true
-    cache_size = CONFIG_BT_LE_SCAN_DUPL_CACHE_SIZE;
+    cache_size = CONFIG_BT_LE_LL_DUP_SCAN_LIST_COUNT;
     if (CONFIG_BT_LE_SCAN_DUPL_TYPE == 0) {
         duplicate_mode = FILTER_DUPLICATE_ADDRESS | FILTER_DUPLICATE_PDUTYPE;
     } else if (CONFIG_BT_LE_SCAN_DUPL_TYPE == 1) {
@@ -1164,7 +1164,7 @@ void esp_ble_controller_log_dump_all(bool output)
     esp_panic_handler_reconfigure_wdts(5000);
     BT_ASSERT_PRINT("\r\n[DUMP_START:");
     ble_log_async_output_dump_all(output);
-    BT_ASSERT_PRINT("]\r\n");
+    BT_ASSERT_PRINT(":DUMP_END]\r\n");
     portEXIT_CRITICAL_SAFE(&spinlock);
 }
 #endif // CONFIG_BT_LE_CONTROLLER_LOG_ENABLED

components/bt/porting/npl/freertos/include/nimble/nimble_npl_os.h

@@ -122,6 +122,7 @@ struct npl_funcs_t {
     void (*p_ble_npl_hw_exit_critical)(uint32_t);
     uint32_t (*p_ble_npl_get_time_forever)(void);
     uint8_t (*p_ble_npl_hw_is_in_critical)(void);
+    void (*p_ble_npl_eventq_put_to_front)(struct ble_npl_eventq *, struct ble_npl_event *);
 };
 
 extern struct npl_funcs_t *npl_funcs;

components/bt/porting/npl/freertos/src/npl_os_freertos.c

@@ -3,7 +3,7 @@
  *
  * SPDX-License-Identifier: Apache-2.0
  *
- * SPDX-FileContributor: 2019-2022 Espressif Systems (Shanghai) CO LTD
+ * SPDX-FileContributor: 2019-2023 Espressif Systems (Shanghai) CO LTD
  */
 
 #include <assert.h>
@@ -37,11 +37,19 @@ static const char *TAG = "Timer";
 #error "not defined SOC_ESP_NIMBLE_CONTROLLER or SOC_ESP_NIMBLE_CONTROLLER is zero"
 #endif
 
+#if CONFIG_BT_NIMBLE_ENABLED
 #define BLE_HOST_CO_COUNT    (8)
 #define BLE_HOST_EV_COUNT    (11 + BLE_HOST_CO_COUNT)
 #define BLE_HOST_EVQ_COUNT   (3)
 #define BLE_HOST_SEM_COUNT   (10)
 #define BLE_HOST_MUTEX_COUNT (4)
+#else
+#define BLE_HOST_CO_COUNT    (0)
+#define BLE_HOST_EV_COUNT    (0)
+#define BLE_HOST_EVQ_COUNT   (0)
+#define BLE_HOST_SEM_COUNT   (0)
+#define BLE_HOST_MUTEX_COUNT (0)
+#endif
 
 struct os_mempool ble_freertos_ev_pool;
 static os_membuf_t *ble_freertos_ev_buf = NULL;
@@ -240,6 +248,32 @@ IRAM_ATTR npl_freertos_eventq_put(struct ble_npl_eventq *evq, struct ble_npl_eve
     BLE_LL_ASSERT(ret == pdPASS);
 }
 
+void
+IRAM_ATTR npl_freertos_eventq_put_to_front(struct ble_npl_eventq *evq, struct ble_npl_event *ev)
+{
+    BaseType_t woken;
+    BaseType_t ret;
+    struct ble_npl_eventq_freertos *eventq = (struct ble_npl_eventq_freertos *)evq->eventq;
+    struct ble_npl_event_freertos *event = (struct ble_npl_event_freertos *)ev->event;
+
+    if (event->queued) {
+        return;
+    }
+
+    event->queued = true;
+
+    if (in_isr()) {
+        ret = xQueueSendToFrontFromISR(eventq->q, &ev, &woken);
+        if( woken == pdTRUE ) {
+            portYIELD_FROM_ISR();
+        }
+    } else {
+        ret = xQueueSendToFront(eventq->q, &ev, portMAX_DELAY);
+    }
+
+    BLE_LL_ASSERT(ret == pdPASS);
+}
+
 void
 IRAM_ATTR npl_freertos_eventq_remove(struct ble_npl_eventq *evq,
                        struct ble_npl_event *ev)
@@ -986,6 +1020,7 @@ const struct npl_funcs_t npl_funcs_ro = {
     .p_ble_npl_eventq_deinit = npl_freertos_eventq_deinit,
     .p_ble_npl_eventq_get = npl_freertos_eventq_get,
     .p_ble_npl_eventq_put = npl_freertos_eventq_put,
+    .p_ble_npl_eventq_put_to_front = npl_freertos_eventq_put_to_front,
     .p_ble_npl_eventq_remove = npl_freertos_eventq_remove,
     .p_ble_npl_event_run = npl_freertos_event_run,
     .p_ble_npl_eventq_is_empty = npl_freertos_eventq_is_empty,

examples/bluetooth/nimble/power_save/sdkconfig.32m.esp32h2

@@ -19,4 +19,5 @@ CONFIG_PM_POWER_DOWN_CPU_IN_LIGHT_SLEEP=y
 # Sleep Config
 #
 CONFIG_ESP_SLEEP_POWER_DOWN_FLASH=y
+CONFIG_ESP_SLEEP_CACHE_SAFE_ASSERTION=y
 # end of Sleep Config

examples/bluetooth/nimble/power_save/sdkconfig.40m.esp32c6

@@ -22,4 +22,5 @@ CONFIG_FREERTOS_USE_TICKLESS_IDLE=y
 #
 CONFIG_ESP_SLEEP_POWER_DOWN_FLASH=y
 CONFIG_ESP_PHY_MAC_BB_PD=y
+CONFIG_ESP_SLEEP_CACHE_SAFE_ASSERTION=y
 # end of Sleep Config

examples/bluetooth/nimble/power_save/sdkconfig.defaults.esp32c2

@@ -17,3 +17,4 @@ CONFIG_XTAL_FREQ=26
 # Sleep Config
 #
 CONFIG_ESP_SLEEP_POWER_DOWN_FLASH=y
+CONFIG_ESP_SLEEP_CACHE_SAFE_ASSERTION=y

examples/bluetooth/nimble/power_save/sdkconfig.defaults.esp32c6

@@ -22,6 +22,7 @@ CONFIG_FREERTOS_USE_TICKLESS_IDLE=y
 #
 CONFIG_ESP_SLEEP_POWER_DOWN_FLASH=y
 CONFIG_ESP_PHY_MAC_BB_PD=y
+CONFIG_ESP_SLEEP_CACHE_SAFE_ASSERTION=y
 # end of Sleep Config
 
 #

examples/bluetooth/nimble/power_save/sdkconfig.defaults.esp32h2

@@ -19,6 +19,7 @@ CONFIG_PM_POWER_DOWN_PERIPHERAL_IN_LIGHT_SLEEP=y
 # Sleep Config
 #
 CONFIG_ESP_SLEEP_POWER_DOWN_FLASH=y
+CONFIG_ESP_SLEEP_CACHE_SAFE_ASSERTION=y
 # end of Sleep Config
 
 #