User space code for DVB blind-scanning, getting spectra and getting IQ constellation samples on tbs based DVB cards. Currently supports:
- stid135-based cards: tbs6909x and tbs6903x
- stv091x based cards: tbs5927
- si2183 based cards: tbs6504
- tas2101 based cards (incomplete): tbs5990, tbs6904
The code requires a patched kernel tree which is available at https://github.com/deeptho/linux_media Always use the latest versions from both repositories, or make sure that the versions match (e.g. the same tag or the same branch). Installation instructions for installing the drivers in Ubuntu can be found in INSTALL.md
There are two methods of spectrum acquisition: sweep and fft. sweep sweeps across the frequency spectrum and measures
narrow band power, taking into account AGC settings. fft uses the builtin fft engine on the stid135 chip to scan
the spectrum in very high resolution (100kHz per default, but 50kHz sometimes detects more narrow band transponders).
The spectrum will be saved to /tmp/spectrum_rf2_H.dat and /tmp/spectrum_rf2_V.dat, or similarly named files.
neumo-blindscan -c spectrum -U8 -a0 --rf-in=2 --spectrum-method sweep --spectral-resolution 2000
will perform a sweep scan with 2MHz resolution. On stid135 this is actually slower than fft scan.
It will get a full spectrum in less 30 seconds with a resolution of 2MHz on tbs5927.
neumo-blindscan -c spectrum -U8 -a0 --rf-in=2 --spectrum-method fft --spectral-resolution 100 will scan a satellite
in less 30 seconds with a resolution of 100kHz on tbs6909x and tbs6903x. This is using the internal high speed fft engine.
Here are some example spectra for 5.0West; horizontal and vertical.
Here is a portion of a 100kHz spectrum captured on 5.0West, horizontal polarization created on tbs6909x It shows several narrow band transponders
The blind scan code scans all or some of the frequency spectrum
available on a DVB-S2 tuner. The scanned portion is the range
[start-freq, end-freq]. Unless -p is specified, both polarizations
will be scanned. There are two ways of scanning: exhaustive and spectral-peaks.
This blind scanner can also scan transponders which have "Physical Layer Scrambling" turned
on. When it discovers such a transponder it uses its built-in codes (for the multistreams on
5.0West). Additional mod_modes/mod_codes can be added using --pls-modes. For example --pls-modes ROOT+12 GOLD+13
adds two codes to try.
It is also possible to specify a range of ROOT+x codes to test. This option is very slow but will take around 90 minutes at most. Currently this is not working on stid135.
The spectrum is scanned in steps of step-freq. The default value is fine for scanning high symbolrate transponders. To scan low symbol rate transponders, set max-symbol-rate to a low value and star-freq close to where they might be.
neumo-blindscan -c blindscan -U8 -a0 --rf-in=2 -pV --spectral-resolution 100 will connect adapter 0
to RF input 2 and scan the full vertical band.
First the spectrum is analyzed to find candidate transponders and then a blindscan is performed
on those transponders. If the transponder locks, the output is saved.
Then the actual blindscan starts and results are printed on the terminal and saved
in /tmp/blindscan_rf2_V.dat. Here is a sample output:
SEARCH: 10700.000-11700.000 pol=V
select rf_in=2
FE_GET_EVENT: stat=543, signal=1 carrier=1 viterbi=1 sync=1 timedout=0 locked=1
RESULT: freq=10719.631V Symrate=27499 Stream=-1 pls_mode= 3:262143 MATYPE: 0xf2
SIG=-26.48dB SIG= 74% CNR=13.50dB CNR= 67% SYS(22) MOD(6) FEC_AUTO INV_OFF PILAUTO ROLL_20
retuning
FE_GET_EVENT: stat=543, signal=1 carrier=1 viterbi=1 sync=1 timedout=0 locked=1
RESULT: freq=10757.991V Symrate=27498 Stream=-1 pls_mode= 3:262143 MATYPE: 0xf2
SIG=-26.60dB SIG= 74% CNR=13.70dB CNR= 68% SYS(22) MOD(6) FEC_AUTO INV_OFF PILAUTO ROLL_20
On stv091x, the code searches for falling or rising edges of transponders. This is less reliable than the stid135 algorithm (see below). After a blindscan succeeds, the spectrum part for that transponder is skipped to avoid double detections and to save time. The main search parameters are
- max-symbol-rate: determines how far to scan from an edge in the spectrum. Set higher for high symbol rates. High values are usually recommended.
On stid135, the code searches for central frequencies of transponders after acquiring the complete spectrum. The spectrum is of high resolution and the peak detector is more sophisticated. As a result most spectral peaks are found, even very weak or very narrow band ones. The code scans all candidate peaks and skips the spectrum part for any found transponder. The main search parameters are:
- search-range: determines how far to search from the center of frequency peaks. A typical vale is 10000
- spectral-resolution: determines how finely to scan the spectrum. Use 50 for very low symbolrates. Otherwise use 100.
The stid135 algorithm's peak finding is more reliable. On the other hand, the actual blindscan is slower for and less reliable for low symbol rates compared to stv091x. Also scanning false peaks is especially slow and this makes scanning slower than it could be. With the current code, scanning a full satellite (H and V; 10700Ghz-12750Ghz) takes a few minutes.
The most influential parameters are spectral-resolution (100kHz is fine, 50kHz is sometimes better), and
search-range (default: 10Mhz, higher is sometimes better). spectral-resolution determines the accuracy
of the spectrum. Candidate peaks may be lost if the value is too high. search-range determines how far from the
candidate peak the blindscan can search for a lock. To find high symbolrate transponders (30Ms/s and more), a
larger value will find more transponders if the peak-finder does not find the center of the transponder, but
rather a value closer to its edges.
Below is an older example for scanning 5.0W with default parameters.
The green pluses indicate the found transponders. The orange ones are the candidate peaks. Several narrow band transponders are found properly (11456H, 2400 kS/s and 11480H, 3124kS/s), but three transponders with very low symbolrate are missed (11458H, 542 kS/s and 11465H, 668kS). 11465H, 668kS can be found sometimes with a spectral resolution setting o5 50kHz and can be tuned to reliably. The other one does not tune, even on stv091x on Linux, even though it can be done on Windows. So the drivers need some more improvement.
On tbs6909x, blindscan can use all tuners
stid135-blindscan -cblindscan -a 0 1 2 3 4 5 6 7 -U8 --rf-in=2 -pV will connect all adapters
to RF input 2 and scan the full vertical band
neumo-tune -a 0 -U 8 -c iq -f 10719000 -pV -n 8000 will connect to adapter 8, tune to 11138V and obtain
8000 IQ samples. The samples will be saved in /tmp/iq_a0_10719.000V.dat
Currently this requires an active DVB signal. This will not work for inactive transponders or continuous stream transponders. The script plotiq.py can be used to view the samples. Ypu will need to install pandas, e.g.,
pip3 install pandas
neumo-tune -a 0 -Ablind --rf-in=2 -U 8 -c tune -f 10719000 -pV will connect adapter 0 to
RF INPUT 2 on the card, send uncommitted switch command 8, tune to 10719V with the specified parameters and then wait forever.
The output will look like this:
adapter=0
rf_in=2
frontend=0
freq=10719000
pol=2
pls_codes[5]={ 4202496, 2048, 98139136, 134216704, 80015360, }
diseqc=UC: U=8 C=-1
Blindscan drivers found
Name of card: TurboSight TBS 6909x
Name of adapter: A0 TBS 6909X
Name of frontend: TurboSight TBS 6909x
Tuning
==========================
Tuning to DVBS1/2 10719.000V
select rf_in=2
BLIND TUNE search-range=10000
FE_GET_EVENT: stat=543, timedout=0 locked=1
FE_READ_STATUS: stat=543, signal=1 carrier=1 viterbi=1 sync=1 timedout=0 locked=1
./neumo-tune -a 0 --rf-in=2 -U 8 -c tune -f 10719000 -pV -S 27500 --delsys DVBS2 --modulation PSK_8 will connect adapter 0 to
RF INPUT 2 on the card, send uncommitted switch command 8, tune to 10719V with the specified parameters and then wait forever.
The output will look like this:
adapter=0
rf_in=2
frontend=0
freq=10719000
pol=2
pls_codes[5]={ 4202496, 2048, 98139136, 134216704, 80015360, }
diseqc=UC: U=8 C=-1
Blindscan drivers found
Name of card: TurboSight TBS 6909x
Name of adapter: A0 TBS 6909X
Name of frontend: TurboSight TBS 6909x
Tuning
==========================
Tuning to DVBS1/2 10719.000V
select rf_in=2
BLIND TUNE search-range=10000
FE_GET_EVENT: stat=543, timedout=0 locked=1
FE_READ_STATUS: stat=543, signal=1 carrier=1 viterbi=1 sync=1 timedout=0 locked=1
Usage: neumo-blindscan [OPTIONS] [L]
Positionals:
L ENUM:value in {C->4,universal->1,wideband->2,wideband-uk->3} OR {4,1,2,3}=1
LNB Type
Options:
-h,--help Print this help message and exit
-c,--command ENUM:value in {blindscan->0,iq->2,spectrum->1} OR {0,2,1}=1
Command to execute
--blindscan-method ENUM:value in {fft->2,sweep->1} OR {2,1}=2
Blindscan method
--delsys ENUM:value in {ATSC->11,ATSCMH->12,AUTO->22,CMMB->14,DAB->15,DCII->21,DSS->4,DTMB->13,DVBC->1,DVBC2->19,DVBH->7,DVBS->5,DVBS2->6,DVBS2X->20,DVBT->3,DVBT2->16,ISDBC->10,ISDBS->9,ISDBT->8,TURBO->17} OR {11,12,22,14,15,21,4,13,1,19,7,5,6,20,3,16,10,9,8,17}=6
Delivery system
--lnb-type ENUM:value in {C->4,universal->1,wideband->2,wideband-uk->3} OR {4,1,2,3}=1
LNB Type
--spectrum-method ENUM:value in {fft->1,sweep->0} OR {1,0}=0
Spectrum method
-a,--adapter INT=0 Adapter number
-r,--rf-in INT=-1 RF input
--frontend INT=0 Frontend number
-s,--start-freq INT=-1 Start of frequency range to scan (kHz)
-e,--end-freq INT=-1 End of frequency range to scan (kHz)
-S,--step-freq INT=6000 Frequency step (kHz)
-R,--spectral-resolution INT=2000
Spectral resolution (kHz)
-F,--fft-size INT=256 FFT size
-M,--max-symbol-rate INT=45000
Maximal symbolrate (kHz)
--search-range INT=10000 Search range (kHz)
-p,--pol INT:value in {BOTH->3,H->1,V->2} OR {3,1,2}=3
Polarization to scan
--pls-modes TEXT=[] ... PLS modes (ROOT, GOLD, COMBO) and code to scan, separated by +
--start-pls-code INT=-1 Start of PLS code range to start (mode=ROOT!)
--end-pls-code INT=-1 End of PLS code range to start (mode=ROOT!)
-d,--diseqc TEXT=UC DiSEqC command string (C: send committed command; U: send uncommitted command
-U,--uncommitted INT=-1 Uncommitted switch number (lowest is 0)
-C,--committed INT=-1 Committed switch number (lowest is 0)
DiSEqC switching signals are sent based on the DiSEqC command string. This string controls the order in which DiSEqC commands are sent, e.g., "UC" means send uncommitted command first, then committed command. "UCU" means that the uncommitted command will be sent twice. The switch ports are specified by the --uncommitted and --committed arguments
Usage: ./neumo-tune [OPTIONS]
Options:
-h,--help Print this help message and exit
-c,--command ENUM:value in {iq->1,tune->0} OR {1,0}=0
Command to execute
-A,--algo ENUM:value in {blind->0,cold->2,warm->1} OR {0,2,1}=0
Algorithm for tuning
-a,--adapter INT=0 Adapter number
-r,--rf-in INT=-1 RF input
--frontend INT=0 Frontend number
-S,--symbol-rate INT=-1 Symbolrate (kHz)
-m,--modulation ENUM:value in {APSK_1024->30,APSK_128->22,APSK_128L->28,APSK_16->10,APSK_16L->25,APSK_256->23,APSK_256L->29,APSK_32->11,APSK_32L->26,APSK_64->21,APSK_64L->27,APSK_8L->24,C_OQPSK->17,C_QPSK->14,DQPSK->12,I_QPSK->15,PSK_8->9,QAM_1024->19,QAM_128->4,QAM_16->1,QAM_256->5,QAM_32->2,QAM_4096->20,QAM_4_NR->13,QAM_512->18,QAM_64->3,QAM_AUTO->6,QPSK->0,Q_QPSK->16,VSB_16->8,VSB_8->7} OR {30,22,28,10,25,23,29,11,26,21,27,24,17,14,12,15,9,19,4,1,5,2,20,13,18,3,6,0,16,8,7}=9
modulation
--delsys ENUM:value in {ATSC->11,ATSCMH->12,AUTO->22,CMMB->14,DAB->15,DCII->21,DSS->4,DTMB->13,DVBC->1,DVBC2->19,DVBH->7,DVBS->5,DVBS2->6,DVBS2X->20,DVBT->3,DVBT2->16,ISDBC->10,ISDBS->9,ISDBT->8,TURBO->17} OR {11,12,22,14,15,21,4,13,1,19,7,5,6,20,3,16,10,9,8,17}=6
Delivery system
-R,--search-range INT=10000 Search range (kHz)
-p,--pol INT:value in {BOTH->3,H->1,V->2} OR {3,1,2}=3
Polarization to scan
-n,--num-samples INT=1024 Number of IQ samples to fetch
-f,--frequency INT=-1 Frequency to tune for getting IQ samples
-s,--stream-id INT=-1 stream_id to select
--pls-code TEXT=[] ... PLS mode (ROOT, GOLD, COMBO) and code (number) to scan, separated by +
--start-pls-code INT=-1 Start of PLS code range to start (mode=ROOT!)
--end-pls-code INT=-1 End of PLS code range to start (mode=ROOT!)
-T,--pls-search-timeout INT=25
Search range timeout
-d,--diseqc TEXT=UC DiSEqC command string (C: send committed command; U: send uncommitted command
-U,--uncommitted INT=-1 Uncommitted switch number (lowest is 0)
-C,--committed INT=-1 Committed switch number (lowest is 0)
Usage: stid135-blindscan [OPTIONS]
Positionals:
L ENUM:value in {C->4,universal->1,wideband->2,wideband-uk->3} OR {4,1,2,3}=1
LNB Type
Options:
-h,--help Print this help message and exit
-c,--command ENUM:value in {blindscan->0,iq->2,spectrum->1} OR {0,2,1}=1
Command to execute
--blindscan-method ENUM:value in {fft->2,sweep->1} OR {2,1}=2
Blindscan method
--delsys ENUM:value in {ATSC->11,ATSCMH->12,AUTO->22,CMMB->14,DAB->15,DCII->21,DSS->4,DTMB->13,DVBC->1,DVBC2->19,DVBH->7,DVBS->5,DVBS2->6,DVBS2X->20,DVBT->3,DVBT2->16,ISDBC->10,ISDBS->9,ISDBT->8,TURBO->17} OR {11,12,22,14,15,21,4,13,1,19,7,5,6,20,3,16,10,9,8,17}=6
Delivery system
--lnb-type ENUM:value in {C->4,universal->1,wideband->2,wideband-uk->3} OR {4,1,2,3}=1
LNB Type
--spectrum-method ENUM:value in {fft->1,sweep->0} OR {1,0}=1
Spectrum method
-a,--adapter INT=[] ... Adapter number
-r,--rf-in INT=-1 RF input
--frontend INT=0 Frontend number
-s,--start-freq INT=-1 Start of frequency range to scan (kHz)
-e,--end-freq INT=-1 End of frequency range to scan (kHz)
-S,--step-freq INT=6000 Frequency step (kHz)
--spectral-resolution INT=0 Spectral resolution (kHz)
-F,--fft-size INT=512 FFT size
-M,--max-symbol-rate INT=45000
Maximal symbolrate (kHz)
-R,--search-range INT=10000 Search range (kHz)
-p,--pol INT:value in {BOTH->3,H->1,V->2} OR {3,1,2}=3
Polarisation to scan
--pls-modes TEXT=[] ... PLS modes (ROOT, GOLD, COMBO) and code to scan, separated by +
--start-pls-code INT=-1 Start of PLS code range to start (mode=ROOT!)
--end-pls-code INT=-1 End of PLS code range to start (mode=ROOT!)
-d,--diseqc TEXT=UC DiSEqC command string (C: send committed command; U: send uncommitted command
-U,--uncommitted INT=-1 Uncommitted switch number (lowest is 0)
-C,--committed INT=-1 Committed switch number (lowest is 0)
The code is compiled with clang++. Make sure it is installed as some versions of g++ have some problems compiling this
cd <whereever you have checkout>
mkdir build
cd build
cmake ..
make
The executable will be located in build/src/blindscan and can be copied to /usr/bin/
