✨🐛 HC32 - Add SERIAL_DMA, fix SDIO and MEATPACK (MarlinFirmware#26845)

* fix meatpack on hc32

* add support for SERIAL_DMA on HC32

* add additional checks in HC32 HAL

* migrate HC32 HAL to use app_config.h

* fix memory leak in HC32 sdio HAL
MarlinFirmware#26845 (comment)

* hc32: fail if both EMERGENCY_PARSER and SERIAL_DMA are enabled

Marlin/Configuration_adv.h

@@ -2698,7 +2698,7 @@
  * This feature is EXPERIMENTAL so use with caution and test thoroughly.
  * Enable this option to receive data on the serial ports via the onboard DMA
  * controller for more stable and reliable high-speed serial communication.
- * Only some STM32 MCUs are currently supported.
+ * Support is currently limited to some STM32 MCUs and all HC32 MCUs.
  * Note: This has no effect on emulated USB serial ports.
  */
 //#define SERIAL_DMA

Marlin/src/HAL/HC32/MarlinHAL.cpp

@@ -123,6 +123,11 @@ void MarlinHAL::init() {
 
   // Register min serial
   TERN_(POSTMORTEM_DEBUGGING, install_min_serial());
+
+  // warn if low memory after init
+  if (freeMemory() < 1024) {
+    SERIAL_WARN_MSG("HAL: low memory after init!\n");
+  }
 }
 
 void MarlinHAL::init_board() {}
@@ -147,7 +152,31 @@ void MarlinHAL::delay_ms(const int ms) {
   delay(ms);
 }
 
-void MarlinHAL::idletask() {}
+void MarlinHAL::idletask() {
+  #if ENABLED(MARLIN_DEV_MODE)
+    // check & print serial RX errors
+    MSerialT *serials[] = { &MSerial1, &MSerial2 };
+    for (int serial = 0; serial < 2; serial++) {
+      usart_receive_error_t err = serials[serial]->getReceiveError();
+      if (err != usart_receive_error_t::None) {
+        // "Warning: MSerial[n] RX [Framing|Parity|Overrun] Error"
+        SERIAL_WARN_START();
+        SERIAL_ECHOPGM(" MSerial");
+        SERIAL_ECHO(serial + 1);
+        SERIAL_ECHOPGM(" RX ");
+        switch(err) {
+          case usart_receive_error_t::FramingError: SERIAL_ECHOPGM("Framing"); break;
+          case usart_receive_error_t::ParityError:  SERIAL_ECHOPGM("Parity");  break;
+          case usart_receive_error_t::OverrunError: SERIAL_ECHOPGM("Overrun"); break;
+          case usart_receive_error_t::RxDataDropped: SERIAL_ECHOPGM("DataDropped"); break;
+          default: break;
+        }
+        SERIAL_ECHOPGM(" Error");
+        SERIAL_EOL();
+      }
+    }
+  #endif
+}
 
 uint8_t MarlinHAL::get_reset_source() {
   // Query reset cause from RMU

Marlin/src/HAL/HC32/MarlinSerial.cpp

@@ -46,14 +46,34 @@ constexpr bool serial_handles_emergency(int port) {
 //
 // Define serial ports
 //
-#define DEFINE_HWSERIAL_MARLIN(name, n)      \
+
+// serial port where RX and TX use IRQs
+#define DEFINE_IRQ_SERIAL_MARLIN(name, n)      \
   MSerialT name(serial_handles_emergency(n), \
                 &USART##n##_config,          \
                 BOARD_USART##n##_TX_PIN,     \
                 BOARD_USART##n##_RX_PIN);
 
-DEFINE_HWSERIAL_MARLIN(MSerial1, 1);
-DEFINE_HWSERIAL_MARLIN(MSerial2, 2);
+// serial port where RX uses DMA and TX uses IRQs
+// all serial ports use DMA1
+// since there are 4 USARTs and 4 DMA channels, we can use the USART number as the DMA channel
+#define DEFINE_DMA_SERIAL_MARLIN(name, n)      \
+  MSerialT name(serial_handles_emergency(n), \
+                &USART##n##_config,          \
+                BOARD_USART##n##_TX_PIN,     \
+                BOARD_USART##n##_RX_PIN,     \
+                M4_DMA1,                     \
+                ((en_dma_channel_t)(n - 1))); // map USART1 to DMA channel 0, USART2 to DMA channel 1, etc.
+
+#define DEFINE_SERIAL_MARLIN(name, n) TERN(SERIAL_DMA, DEFINE_DMA_SERIAL_MARLIN(name, n), DEFINE_IRQ_SERIAL_MARLIN(name, n))
+
+DEFINE_SERIAL_MARLIN(MSerial1, 1);
+DEFINE_SERIAL_MARLIN(MSerial2, 2);
+
+// TODO: remove this warning when SERIAL_DMA has been tested some more
+#if ENABLED(SERIAL_DMA)
+  #warning "SERIAL_DMA may be unstable on HC32F460."
+#endif
 
 //
 // Serial port assertions

Marlin/src/HAL/HC32/MarlinSerial.h

@@ -25,17 +25,42 @@
 #include <drivers/usart/Usart.h>
 
 // Optionally set uart IRQ priority to reduce overflow errors
-// #define UART_IRQ_PRIO 1
+//#define UART_RX_IRQ_PRIO 1
+//#define UART_TX_IRQ_PRIO 1
+//#define UART_RX_DMA_IRQ_PRIO 1
 
 struct MarlinSerial : public Usart {
-  MarlinSerial(struct usart_config_t *usart_device, gpio_pin_t tx_pin, gpio_pin_t rx_pin) : Usart(usart_device, tx_pin, rx_pin) {}
+  MarlinSerial(
+    struct usart_config_t *usart_device, 
+    gpio_pin_t tx_pin, 
+    gpio_pin_t rx_pin
+    #if ENABLED(SERIAL_DMA)
+    , M4_DMA_TypeDef *dma_unit = nullptr,
+    en_dma_channel_t rx_dma_channel = DmaCh0
+    #endif
+  ) : Usart(usart_device, tx_pin, rx_pin) {
+    #if ENABLED(SERIAL_DMA)
+      if (dma_unit != nullptr) {
+        enableRxDma(dma_unit, rx_dma_channel);
+      }
+    #endif
+  }
 
-  #ifdef UART_IRQ_PRIO
+  #if defined(UART_RX_IRQ_PRIO) || defined(UART_TX_IRQ_PRIO) || defined(UART_RX_DMA_IRQ_PRIO)
     void setPriority() {
-      NVIC_SetPriority(c_dev()->interrupts.rx_data_available.interrupt_number, UART_IRQ_PRIO);
-      NVIC_SetPriority(c_dev()->interrupts.rx_error.interrupt_number, UART_IRQ_PRIO);
-      NVIC_SetPriority(c_dev()->interrupts.tx_buffer_empty.interrupt_number, UART_IRQ_PRIO);
-      NVIC_SetPriority(c_dev()->interrupts.tx_complete.interrupt_number, UART_IRQ_PRIO);
+      #if defined(UART_RX_IRQ_PRIO)
+        NVIC_SetPriority(c_dev()->interrupts.rx_data_available.interrupt_number, UART_RX_IRQ_PRIO);
+        NVIC_SetPriority(c_dev()->interrupts.rx_error.interrupt_number, UART_RX_IRQ_PRIO);
+      #endif
+
+      #if defined(UART_TX_IRQ_PRIO)
+        NVIC_SetPriority(c_dev()->interrupts.tx_buffer_empty.interrupt_number, UART_TX_IRQ_PRIO);
+        NVIC_SetPriority(c_dev()->interrupts.tx_complete.interrupt_number, UART_TX_IRQ_PRIO);
+      #endif
+
+      #if defined(UART_RX_DMA_IRQ_PRIO) && ENABLED(SERIAL_DMA)
+        NVIC_SetPriority(c_dev()->dma.rx.rx_data_available_dma_btc.interrupt_number, UART_RX_DMA_IRQ_PRIO);
+      #endif
     }
 
     void begin(uint32_t baud) {
@@ -47,7 +72,12 @@ struct MarlinSerial : public Usart {
       Usart::begin(baud, config);
       setPriority();
     }
-  #endif
+
+    void begin(uint32_t baud, const stc_usart_uart_init_t *config, const bool rxNoiseFilter = true) {
+      Usart::begin(baud, config, rxNoiseFilter);
+      setPriority();
+    }
+  #endif // UART_RX_IRQ_PRIO || UART_TX_IRQ_PRIO || UART_RX_DMA_IRQ_PRIO
 };
 
 typedef Serial1Class<MarlinSerial> MSerialT;

Marlin/src/HAL/HC32/app_config.h

@@ -0,0 +1,70 @@
+/**
+ * app_config.h is included by the hc32f460 arduino build script for every source file.
+ * it is used to configure the arduino core (and ddl) automatically according 
+ * to the settings in Configuration.h and Configuration_adv.h.
+ */
+#pragma once
+#ifndef _HC32_APP_CONFIG_H_
+#define _HC32_APP_CONFIG_H_
+
+#include "../../inc/MarlinConfigPre.h"
+
+//
+// dev mode
+//
+#if ENABLED(MARLIN_DEV_MODE)
+  #define __DEBUG 1
+  #define __CORE_DEBUG 1
+#endif
+
+//
+// Fault Handlers and Panic
+//
+
+#if ENABLED(POSTMORTEM_DEBUGGING)
+  // disable arduino core fault handler, as we define our own
+  #define CORE_DISABLE_FAULT_HANDLER 1
+#endif
+
+// force-enable panic handler so that we can use our custom one (in MinSerial)
+#define PANIC_ENABLE 1
+
+// use short filenames in ddl debug and core panic output
+#define __DEBUG_SHORT_FILENAMES 1
+#define __PANIC_SHORT_FILENAMES 1
+
+// omit panic messages in core panic output
+#define __OMIT_PANIC_MESSAGE 1
+
+//
+// Usart
+//
+
+// disable serial globals (Serial1, Serial2, ...), as we define our own
+#define DISABLE_SERIAL_GLOBALS 1
+
+// increase the size of the Usart buffers (both RX and TX)
+// NOTE: 
+// the heap usage will increase by (SERIAL_BUFFER_SIZE - 64) * "number of serial ports used"
+// if running out of heap, the system may become unstable
+//#define SERIAL_BUFFER_SIZE 256
+
+// enable support for Usart Clock Divider / Oversampling auto config
+#define USART_AUTO_CLKDIV_OS_CONFIG 1
+
+// enable USART_RX_DMA_SUPPORT core option when SERIAL_DMA is enabled
+#if ENABLED(SERIAL_DMA)
+  #define USART_RX_DMA_SUPPORT 1
+#endif
+
+//
+// Misc.
+//
+
+// redirect printf to host serial
+#define REDIRECT_PRINTF_TO_SERIAL 1
+
+// FIXME override F_CPU to PCLK1, as marlin freaks out otherwise
+#define F_CPU (SYSTEM_CLOCK_FREQUENCIES.pclk1)
+
+#endif // _HC32_APP_CONFIG_H_

Marlin/src/HAL/HC32/inc/SanityCheck.h

@@ -20,6 +20,20 @@
  *
  */
 #pragma once
+#include <core_util.h>
+
+#if !defined(ARDUINO_CORE_VERSION_INT) || !defined(GET_VERSION_INT)
+  // version macros were introduced in arduino core version 1.1.0
+  // below that version, we polyfill them
+  #define GET_VERSION_INT(major, minor, patch) ((major * 100000) + (minor * 1000) + patch)
+  #define ARDUINO_CORE_VERSION_INT GET_VERSION_INT(1, 0, 0)
+#endif
+
+#if ARDUINO_CORE_VERSION_INT < GET_VERSION_INT(1, 1, 0)
+  // because we use app_config.h introduced in arduino core version 1.1.0, the 
+  // HAL is not compatible with older versions
+  #error "The HC32 HAL is not compatible with Arduino Core versions < 1.1.0. Consider updating the Arduino Core."
+#endif
 
 #ifndef BOARD_XTAL_FREQUENCY
   #error "BOARD_XTAL_FREQUENCY is required for HC32F460."
@@ -74,3 +88,18 @@
     #error "HC32 HAL uses a custom panic handler. Do not define PANIC_USARTx_TX_PIN."
   #endif
 #endif
+
+#if ENABLED(SERIAL_DMA)
+  #if !defined(USART_RX_DMA_SUPPORT)
+    #error "SERIAL_DMA requires USART_RX_DMA_SUPPORT to be enabled in the arduino core."
+  #endif
+
+  // USART_RX_DMA_SUPPORT does not implement core_hook_usart_rx_irq, which is required for the emergency parser
+  #if ENABLED(EMERGENCY_PARSER)
+    #error "EMERGENCY_PARSER is not supported with SERIAL_DMA. Please disable either SERIAL_DMA or EMERGENCY_PARSER."
+  #endif
+
+  #if ARDUINO_CORE_VERSION_INT < GET_VERSION_INT(1, 1, 0)
+    #error "SERIAL_DMA is not supported with arduino core version < 1.1.0."
+  #endif
+#endif

Marlin/src/HAL/HC32/sdio.cpp

@@ -54,7 +54,7 @@
     fn                                              \
   }
 
-stc_sd_handle_t *handle;
+stc_sd_handle_t *handle = nullptr;
 
 bool SDIO_Init() {
   // Configure SDIO pins
@@ -66,36 +66,45 @@ bool SDIO_Init() {
   GPIO_SetFunc(BOARD_SDIO_CMD, Func_Sdio);
   GPIO_SetFunc(BOARD_SDIO_DET, Func_Sdio);
 
+  // If a handle is already initialized, free it before creating a new one
+  // otherwise, we will leak memory, which will eventually crash the system
+  if (handle != nullptr) {
+    delete handle->pstcDmaInitCfg;
+    delete handle->pstcCardInitCfg;
+    delete handle;
+    handle = nullptr;
+  }
+
   // Create DMA configuration
   stc_sdcard_dma_init_t *dmaConf = new stc_sdcard_dma_init_t;
   dmaConf->DMAx = SDIO_DMA_PERIPHERAL;
   dmaConf->enDmaCh = SDIO_DMA_CHANNEL;
 
+  // Create card configuration
+  // This should be a fairly safe configuration for most cards
+  stc_sdcard_init_t *cardConf = new stc_sdcard_init_t;
+  cardConf->enBusWidth = SdiocBusWidth4Bit;
+  cardConf->enClkFreq = SdiocClk400K;
+  cardConf->enSpeedMode = SdiocNormalSpeedMode;
+  cardConf->pstcInitCfg = nullptr;
+
   // Create handle in DMA mode
   handle = new stc_sd_handle_t;
   handle->SDIOCx = SDIO_PERIPHERAL;
   handle->enDevMode = SdCardDmaMode;
   handle->pstcDmaInitCfg = dmaConf;
-
-  // Create card configuration
-  // This should be a fairly safe configuration for most cards
-  stc_sdcard_init_t cardConf = {
-    .enBusWidth = SdiocBusWidth4Bit,
-    .enClkFreq = SdiocClk400K,
-    .enSpeedMode = SdiocNormalSpeedMode,
-    //.pstcInitCfg = NULL,
-  };
+  //handle->pstcCardInitCfg = cardConf; // assigned in SDCARD_Init
 
   // Initialize sd card
-  en_result_t rc = SDCARD_Init(handle, &cardConf);
+  en_result_t rc = SDCARD_Init(handle, cardConf);
   if (rc != Ok) printf("SDIO_Init() error (rc=%u)\n", rc);
 
   return rc == Ok;
 }
 
 bool SDIO_ReadBlock(uint32_t block, uint8_t *dst) {
-  CORE_ASSERT(handle != NULL, "SDIO not initialized");
-  CORE_ASSERT(dst != NULL, "SDIO_ReadBlock dst is NULL");
+  CORE_ASSERT(handle != nullptr, "SDIO not initialized", return false);
+  CORE_ASSERT(dst != nullptr, "SDIO_ReadBlock dst is NULL", return false);
 
   WITH_RETRY(SDIO_READ_RETRIES, {
     en_result_t rc = SDCARD_ReadBlocks(handle, block, 1, dst, SDIO_READ_TIMEOUT);
@@ -107,8 +116,8 @@ bool SDIO_ReadBlock(uint32_t block, uint8_t *dst) {
 }
 
 bool SDIO_WriteBlock(uint32_t block, const uint8_t *src) {
-  CORE_ASSERT(handle != NULL, "SDIO not initialized");
-  CORE_ASSERT(src != NULL, "SDIO_WriteBlock src is NULL");
+  CORE_ASSERT(handle != nullptr, "SDIO not initialized", return false);
+  CORE_ASSERT(src != nullptr, "SDIO_WriteBlock src is NULL", return false);
 
   WITH_RETRY(SDIO_WRITE_RETRIES, {
     en_result_t rc = SDCARD_WriteBlocks(handle, block, 1, (uint8_t *)src, SDIO_WRITE_TIMEOUT);
@@ -120,12 +129,12 @@ bool SDIO_WriteBlock(uint32_t block, const uint8_t *src) {
 }
 
 bool SDIO_IsReady() {
-  CORE_ASSERT(handle != NULL, "SDIO not initialized");
+  CORE_ASSERT(handle != nullptr, "SDIO not initialized", return false);
   return bool(handle->stcCardStatus.READY_FOR_DATA);
 }
 
 uint32_t SDIO_GetCardSize() {
-  CORE_ASSERT(handle != NULL, "SDIO not initialized");
+  CORE_ASSERT(handle != nullptr, "SDIO not initialized", return 0);
 
   // Multiply number of blocks with block size to get size in bytes
   const uint64_t cardSizeBytes = uint64_t(handle->stcSdCardInfo.u32LogBlockNbr) * uint64_t(handle->stcSdCardInfo.u32LogBlockSize);

Marlin/src/inc/SanityCheck.h

@@ -235,9 +235,11 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
   #error "SERIAL_XON_XOFF and SERIAL_STATS_* features not supported on USB-native AVR devices."
 #endif
 
-// Serial DMA is only available for some STM32 MCUs
+// Serial DMA is only available for some STM32 MCUs and HC32
 #if ENABLED(SERIAL_DMA)
-  #if !HAL_STM32 || NONE(STM32F0xx, STM32F1xx, STM32F2xx, STM32F4xx, STM32F7xx)
+  #if defined(ARDUINO_ARCH_HC32)
+    // checks for HC32 are located in HAL/HC32/inc/SanityCheck.h
+  #elif !HAL_STM32 || NONE(STM32F0xx, STM32F1xx, STM32F2xx, STM32F4xx, STM32F7xx)
     #error "SERIAL_DMA is only available for some STM32 MCUs and requires HAL/STM32."
   #elif !defined(HAL_UART_MODULE_ENABLED) || defined(HAL_UART_MODULE_ONLY)
     #error "SERIAL_DMA requires STM32 platform HAL UART (without HAL_UART_MODULE_ONLY)."