Report couin3 / master

RFLink/1_Radio.cpp

@@ -9,9 +9,7 @@
 #include "RFLink.h"
 #include "1_Radio.h"
 #include "4_Display.h"
-#ifdef AUTOCONNECT_ENABLED
-#include "9_AutoConnect.h"
-#else
+
 uint8_t PIN_RF_RX_PMOS = PIN_RF_RX_PMOS_0;
 uint8_t PIN_RF_RX_NMOS = PIN_RF_RX_NMOS_0;
 uint8_t PIN_RF_RX_VCC = PIN_RF_RX_VCC_0;
@@ -25,7 +23,6 @@ uint8_t PIN_RF_TX_VCC = PIN_RF_TX_VCC_0;
 uint8_t PIN_RF_TX_GND = PIN_RF_TX_GND_0;
 uint8_t PIN_RF_TX_NA = PIN_RF_TX_NA_0;
 uint8_t PIN_RF_TX_DATA = PIN_RF_TX_DATA_0;
-#endif //AUTOCONNECT_ENABLED
 
 Radio_State current_State = Radio_NA;
 
@@ -45,7 +42,12 @@ void set_Radio_mode(Radio_State new_State)
     case Radio_OFF:
       PIN_RF_RX_DATA = NOT_A_PIN;
       PIN_RF_TX_DATA = NOT_A_PIN;
+      radio.reset();
       radio.initialize();
+      radio.setFrequency(433920000);
+      Serial.print("Freq = ");
+      Serial.println(radio.getFrequency());
+      //Serial.print("Temp = "); Serial.println(radio.readTemperature());
       radio.setHighPower(true); // for RFM69HW
       // radio.sleep();
       break;

RFLink/1_Radio.h

@@ -108,4 +108,4 @@ void set_Radio_mode(Radio_State new_state);
 #if (defined(ESP8266) || defined(ESP32))
 void show_Radio_Pin();
 #endif // ESP8266 || ESP32
-#endif // Radio_h
+#endif // Radio_h

RFLink/2_Signal.h

@@ -10,15 +10,15 @@
 
 #include <Arduino.h>
 
-#define RAW_BUFFER_SIZE 292         // 292        // Maximum number of pulses that is received in one go.
-#define MIN_RAW_PULSES 50           // 50         // Minimal number of bits that need to have been received before we spend CPU time on decoding the signal.
-#define RAWSIGNAL_SAMPLE_RATE 32    // 32         // =8 bits. Sample width / resolution in uSec for raw RF pulses.
-#define SIGNAL_SEEK_TIMEOUT_MS 25   // 25         // After this time in mSec, RF signal will be considered absent.
-#define SIGNAL_MIN_PREAMBLE_US 400  // 400        // After this time in uSec, a RF signal will be considered to have started.
-#define MIN_PULSE_LENGTH_US 100     // 250        // Pulses shorter than this value in uSec. will be seen as garbage and not taken as actual pulses.
-#define SIGNAL_END_TIMEOUT_US 5000  // 5000       // After this time in uSec, the RF signal will be considered to have stopped.
-#define SIGNAL_REPEAT_TIME_MS 250   // 500        // Time in mSec. in which the same RF signal should not be accepted again. Filters out retransmits.
-#define SCAN_HIGH_TIME_MS 50        // 50         // time interval in ms. fast processing for background tasks
+#define RAW_BUFFER_SIZE 292        // 292        // Maximum number of pulses that is received in one go.
+#define MIN_RAW_PULSES 50          // 50         // Minimal number of bits that need to have been received before we spend CPU time on decoding the signal.
+#define RAWSIGNAL_SAMPLE_RATE 32   // 32         // =8 bits. Sample width / resolution in uSec for raw RF pulses.
+#define SIGNAL_SEEK_TIMEOUT_MS 25  // 25         // After this time in mSec, RF signal will be considered absent.
+#define SIGNAL_MIN_PREAMBLE_US 400 // 400        // After this time in uSec, a RF signal will be considered to have started.
+#define MIN_PULSE_LENGTH_US 100    // 250        // Pulses shorter than this value in uSec. will be seen as garbage and not taken as actual pulses.
+#define SIGNAL_END_TIMEOUT_US 5000 // 5000       // After this time in uSec, the RF signal will be considered to have stopped.
+#define SIGNAL_REPEAT_TIME_MS 250  // 500        // Time in mSec. in which the same RF signal should not be accepted again. Filters out retransmits.
+#define SCAN_HIGH_TIME_MS 50       // 50         // time interval in ms. fast processing for background tasks
 
 struct RawSignalStruct // Raw signal variabelen places in a struct
 {
@@ -45,4 +45,4 @@ boolean ScanEvent(void);
 
 void AC_Send(unsigned long data, byte cmd);
 
-#endif
+#endif

RFLink/3_Serial.cpp

@@ -49,36 +49,6 @@ boolean CheckMQTT(byte *byte_in)
   return false;
 }
 
-#ifdef AUTOCONNECT_ENABLED
-boolean CheckWeb(String &String_in)
-{
-  if (!String_in.isEmpty())
-  {
-    String_in.trim();
-    char char_in[INPUT_COMMAND_SIZE];
-    String_in.toCharArray(char_in, String_in.length() + 1);
-    char_in[String_in.length() + 1] = 0;
-
-    if (CopySerial(char_in))
-    {
-#ifdef SERIAL_ENABLED
-      Serial.flush();
-      Serial.print(F("Message arrived [Web] "));
-      Serial.println(InputBuffer_Serial);
-#endif
-      if (CheckCmd())
-      {
-        String_in.clear();
-        return true;
-      }
-    }
-    String_in.clear();
-    return false;
-  }
-  return false;
-}
-#endif // AUTOCONNECT_ENABLED
-
 boolean CopySerial(char *src)
 {
   return (strncpy(InputBuffer_Serial, src, INPUT_COMMAND_SIZE - 2));
@@ -262,4 +232,4 @@ boolean CheckCmd()
   return true;
 }
 
-/*********************************************************************************************/
+/*********************************************************************************************/

RFLink/3_Serial.h

@@ -18,7 +18,4 @@ extern char InputBuffer_Serial[INPUT_COMMAND_SIZE];
 
 boolean CheckSerial();
 boolean CheckMQTT(byte *);
-#ifdef AUTOCONNECT_ENABLED
-boolean CheckWeb(String &);
-#endif // AUTOCONNECT_ENABLED
-#endif
+#endif

RFLink/4_Display.cpp

@@ -658,4 +658,4 @@ String GPIO2String(uint8_t uGPIO)
   else
     return "NOT_A_PIN";
 }
-#endif // ESP32
+#endif // ESP32