ktls: release APIs as unstable

api/unstable/ktls.h

@@ -0,0 +1,115 @@
+/*
+* Copyright Amazon.com, Inc. or its affiliates. All Rights Reserved.
+*
+* Licensed under the Apache License, Version 2.0 (the "License").
+* You may not use this file except in compliance with the License.
+* A copy of the License is located at
+*
+*  http://aws.amazon.com/apache2.0
+*
+* or in the "license" file accompanying this file. This file is distributed
+* on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either
+* express or implied. See the License for the specific language governing
+* permissions and limitations under the License.
+*/
+
+#pragma once
+
+#include <s2n.h>
+
+/**
+ * @file ktls.h
+ *
+ * The following APIs enable applications to use kernel TLS (kTLS), meaning that
+ * encrypting and decrypting TLS records is handled by the kernel rather than by
+ * the s2n-tls library.
+ *
+ * The kTLS APIs are currently considered unstable. kTLS is a relatively new
+ * feature with limited and volatile support from different kernels and hardware.
+ *
+ * Currently, s2n-tls supports ktls for only very limited scenarios:
+ * - You must be using Linux. We have not tested with other kernels.
+ * - Your kernel must support kTLS. For Linux, versions >4.13 should support kTLS.
+ * - The TLS kernel module must be enabled. While some environments enable the
+ *   module by default, most will require you to run `sudo modprobe tls`.
+ * - You must negotiate TLS1.2. TLS1.3 support is blocked on kernel support for
+ *   TLS KeyUpdate messages.
+ * - You must negotiate AES128-GCM, which is the most preferred cipher suite
+ *   in the "default" security policy. Other ciphers are supported by the kernel,
+ *   but not implemented in s2n-tls yet.
+ */
+
+/**
+ * Enables sending using kTLS on a given connection.
+ *
+ * See above for the limitations on when kTLS can be enabled. Additionally,
+ * s2n_connection_ktls_enable_send must be called after the handshake completes.
+ * It may be called after some application data is sent and received without kTLS,
+ * but there must be no pending application data that requires flushing. If these
+ * requirements are not met, enabling kTLS will fail with an error.
+ *
+ * After kTLS is enabled for sending, s2n_send, s2n_sendv, and s2n_sendv_with_offset
+ * will use kTLS. kTLS should result in memory and CPU savings. s2n_sendfile will
+ * also become available.
+ *
+ * For applications using kTLS to avoid copying or allocating memory, s2n_sendv
+ * should be preferred over s2n_sendv_with_offset. For s2n_sendv_with_offset,
+ * s2n-tls may need to copy the provided iovec array to apply the offset, and may
+ * need to allocate memory to copy large (>16) iovec arrays.
+ *
+ * If kTLS is enabled for sending, s2n_connection_get_wire_bytes_out will always
+ * return 0 instead of an accurate count.
+ *
+ * @warning Due to the uncertainty around kTLS support, the signature of this
+ * method is likely to change before kTLS is marked as stable.
+ *
+ * @param conn A pointer to the connection.
+ * @returns S2N_SUCCESS if kTLS is successfully enabled. If kTlS is not successfully
+ * enabled, returns S2N_FAILURE but the connection may proceed without kTLS.
+ */
+S2N_API int s2n_connection_ktls_enable_send(struct s2n_connection *conn);
+
+/**
+ * Enables receiving using kTLS on a given connection.
+ *
+ * See above for the limitations on when kTLS can be enabled. Additionally,
+ * s2n_connection_ktls_enable_recv must be called after the handshake completes.
+ * It may be called after some application data is sent and received without kTLS,
+ * but there must be no buffered application data that requires draining. If these
+ * requirements are not met, enabling kTLS will fail with an error.
+ *
+ * After kTLS is enabled for receiving, s2n_recv will use kTLS. This may result
+ * in memory and CPU savings, but currently will still buffer and copy application data.
+ * We will further optimize s2n_recv for kTLS in the future.
+ *
+ * If kTLS is enabled for receiving, s2n_connection_get_wire_bytes_in will always
+ * return 0 instead of an accurate count.
+ *
+ * @warning Due to the uncertainty around kTLS support, the signature of this
+ * method is likely to change before kTLS is marked as stable.
+ *
+ * @param conn A pointer to the connection.
+ * @returns S2N_SUCCESS if kTLS is successfully enabled. If kTlS is not successfully
+ * enabled, returns S2N_FAILURE but the connection may proceed without kTLS.
+ */
+S2N_API int s2n_connection_ktls_enable_recv(struct s2n_connection *conn);
+
+/**
+ * Sends the contents of a file as application data.
+ *
+ * s2n_sendfile should be more efficient than s2n_send because the copy between
+ * the file and the write socket happens inside the kernel.
+ *
+ * This method is only supported if kTLS is enabled for sending.
+ *
+ * @param conn A pointer to the connection.
+ * @param fd The file descriptor to read from. It must be opened for reading and
+ * support mmap-like operations (i.e., it cannot be a socket).
+ * @param offset The offset in the file to begin reading at.
+ * @param count The maximum number of bytes to read from the file.
+ * @param bytes_written Will be set to the number of bytes written if successful.
+ * @param blocked Will be set to the blocked status if an `S2N_ERR_T_BLOCKED` error is returned.
+ * @returns S2N_SUCCESS if any bytes are successfully written, S2N_FAILURE otherwise.
+ */
+S2N_API int s2n_sendfile(struct s2n_connection *conn, int fd, off_t offset, size_t count,
+        size_t *bytes_written, s2n_blocked_status *blocked);

bindings/rust/generate/src/main.rs

@@ -124,7 +124,7 @@ const COPYRIGHT: &str = r#"
 const PRELUDE: &str = r#"
 #![allow(unused_imports, non_camel_case_types)]
 
-use libc::{iovec, FILE};
+use libc::{iovec, FILE, off_t};
 "#;
 
 fn base_builder() -> bindgen::Builder {

tls/s2n_ktls.h

@@ -17,6 +17,7 @@
 
 #include <sys/socket.h>
 
+#include "api/unstable/ktls.h"
 #include "tls/s2n_connection.h"
 /* Define headers needed to enable and use kTLS.
  *