m

content/en/plugins/zlequalizer/manual.md

@@ -48,11 +48,11 @@ ___
 
 You can open the [match analyzer](#match-analyzer) and the [match control panel](#match-control-panel) by clicking `Match` and close them by clicking `Match` again.
 
-When those two panels are visible, you cannot interact with the spectrum and the original [left panel](#left-panel) and [right panel](#right-panel) are hidden. At the same time, the refresh rate will be halved to reduce rendering pressure. 
+When those two panels are visible, you cannot interact with the spectrum and the [left panel](#left-panel) and [right panel](#right-panel) are hidden. At the same time, the refresh rate will be halved to reduce rendering pressure. 
 
-Input/Target/Difference curves are kept alive only when those two panels are visible. Once you close those two panels or close the plugin window, the curves will get reset.
+Input/Target/Difference curves are kept alive only when those two panels are visible. Once you close those two panels (by clicking `Match`) or close the plugin window, the curves will get reset.
 
-For more information, please refer to the [Equalizer Match](#equalizer-match) section.
+For more information, please refer to [Equalization Match](#equalization-match).
 
 ___
 
@@ -739,7 +739,7 @@ All filters are still in Minimum Phase. Additionally, it uses a short FIR filter
 
 It has analog prototype magnitude response and zero phase response. This FIR filter causes about 171 ms latency (up to about 512 ms if left/right or mid/side are used). You should NOT modulate parameters of filters. Dynamic effect does not work.
 
-## Equalizer Match
+## Equalization Match
 
 EQ match uses several filters to match the frequency spectrum of the input signal to the frequency spectrum of the target signal. The steps are listed as follows:
 

content/zh-cn/plugins/zlequalizer/manual.md

@@ -46,13 +46,13 @@ ___
 
 #### 匹配设置
 
-您可以通过点击`Match`来打开[匹配分析器](#匹配分析器)和[匹配控制面板](#匹配控制面板)，再次点击`Match`即可将它们关闭。
+单击`Match`后将打开[匹配分析器](#匹配分析器)和[匹配控制面板](#匹配控制面板)，之后再次单击`Match`即可将它们关闭。
 
-当这两个面板可见时，您无法与频谱进行交互，原始的[左侧面板](#左侧面板)和[右侧面板](#右侧面板)将被隐藏。同时，为了减少渲染压力，刷新率会降低一半。
+当这两个面板显示时，您无法与频谱图进行交互，[左侧面板](#左侧面板)和[右侧面板](#右侧面板)也将被隐藏。同时，为了减少渲染压力，刷新率会降为一半。
 
-只有在这两个面板可见时，输入/目标/差异曲线才会保持激活状态。一旦您关闭这两个面板或关闭插件窗口，曲线将被重置。
+只有在这两个面板显示时，输入/目标/差值曲线才会保持激活状态。一旦您通过单击`Match`关闭这两个面板或关闭插件窗口，这些曲线将被重置。
 
-欲了解更多信息，请参考[均衡匹配](#均衡匹配)部分。
+更多信息请参考[均衡匹配](#均衡匹配)。
 
 ___