* use most actual config

TyMi · Mar 11, 2021 · b5c4ef2 · b5c4ef2
1 parent 7cafa4e
commit b5c4ef2
Show file tree

Hide file tree

Showing 2 changed files with 381 additions and 173 deletions.
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
@@ -42,30 +42,29 @@
 //===========================================================================
 
 /**
- * Here are some standard links for getting your machine calibrated:
+ * Here are some useful links to help get your machine configured and calibrated:
  *
- * https://reprap.org/wiki/Calibration
- * https://youtu.be/wAL9d7FgInk
- * http://calculator.josefprusa.cz
- * https://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
- * https://www.thingiverse.com/thing:5573
- * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
- * https://www.thingiverse.com/thing:298812
+ * Example Configs:     https://github.com/MarlinFirmware/Configurations/branches/all
+ *
+ * Průša Calculator:    https://blog.prusaprinters.org/calculator_3416/
+ *
+ * Calibration Guides:  https://reprap.org/wiki/Calibration
+ *                      https://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide
+ *                      https://sites.google.com/site/repraplogphase/calibration-of-your-reprap
+ *                      https://youtu.be/wAL9d7FgInk
+ *
+ * Calibration Objects: https://www.thingiverse.com/thing:5573
+ *                      https://www.thingiverse.com/thing:1278865
  */
 
 //===========================================================================
-//============================= DELTA Printer ===============================
+//========================== DELTA / SCARA / TPARA ==========================
 //===========================================================================
-// For a Delta printer, start with one of the configuration files in the config/examples/delta directory
-// from https://github.com/MarlinFirmware/Configurations/branches/all and customize for your machine.
 //
-
-//===========================================================================
-//============================= SCARA Printer ===============================
-//===========================================================================
-// For a SCARA printer, start with one of the configuration files in the config/examples/SCARA directory
-// from https://github.com/MarlinFirmware/Configurations/branches/all and customize for your machine.
+// Download configurations from the link above and customize for your machine.
+// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
 //
+//===========================================================================
 
 // @section info
 
@@ -164,8 +163,8 @@
  *   PRUSA_MMU1      : Průša MMU1 (The "multiplexer" version)
  *   PRUSA_MMU2      : Průša MMU2
  *   PRUSA_MMU2S     : Průša MMU2S (Requires MK3S extruder with motion sensor, EXTRUDERS = 5)
- *   SMUFF_EMU_MMU2  : Technik Gegg SMUFF (Průša MMU2 emulation mode)
- *   SMUFF_EMU_MMU2S : Technik Gegg SMUFF (Průša MMU2S emulation mode)
+ *   SMUFF_EMU_MMU2  : Technik Gegg SMuFF (Průša MMU2 emulation mode)
+ *   SMUFF_EMU_MMU2S : Technik Gegg SMuFF (Průša MMU2S emulation mode)
  *
  * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails.
  * See additional options in Configuration_adv.h.
@@ -330,8 +329,10 @@
     #define AUTO_POWER_E_FANS
     #define AUTO_POWER_CONTROLLERFAN
     #define AUTO_POWER_CHAMBER_FAN
+    #define AUTO_POWER_COOLER_FAN
     //#define AUTO_POWER_E_TEMP        50 // (°C) Turn on PSU if any extruder is over this temperature
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU if the chamber is over this temperature
+    //#define AUTO_POWER_COOLER_TEMP   26 // (°C) Turn on PSU if the cooler is over this temperature
     #define POWER_TIMEOUT              30 // (s) Turn off power if the machine is idle for this duration
     //#define POWER_OFF_DELAY          60 // (s) Delay of poweroff after M81 command. Useful to let fans run for extra time.
   #endif
@@ -419,6 +420,7 @@
 #define TEMP_SENSOR_BED 1
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
+#define TEMP_SENSOR_COOLER 0
 
 // Dummy thermistor constant temperature readings, for use with 998 and 999
 #define DUMMY_THERMISTOR_998_VALUE  25
@@ -443,6 +445,10 @@
 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
+#define TEMP_CHAMBER_RESIDENCY_TIME 10  // (seconds) Time to wait for chamber to "settle" in M191
+#define TEMP_CHAMBER_WINDOW      1  // (°C) Temperature proximity for the "temperature reached" timer
+#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
 #define HEATER_0_MINTEMP   0
@@ -454,6 +460,7 @@
 #define HEATER_6_MINTEMP   5
 #define HEATER_7_MINTEMP   5
 #define BED_MINTEMP        0
+#define CHAMBER_MINTEMP    5
 
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
@@ -467,6 +474,16 @@
 #define HEATER_6_MAXTEMP 275
 #define HEATER_7_MAXTEMP 275
 #define BED_MAXTEMP      120
+#define CHAMBER_MAXTEMP  60
+
+/**
+ * Thermal Overshoot
+ * During heatup (and printing) the temperature can often "overshoot" the target by many degrees
+ * (especially before PID tuning). Setting the target temperature too close to MAXTEMP guarantees
+ * a MAXTEMP shutdown! Use these values to forbid temperatures being set too close to MAXTEMP.
+ */
+#define HOTEND_OVERSHOOT 15   // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT
+#define BED_OVERSHOOT    10   // (°C) Forbid temperatures over MAXTEMP - OVERSHOOT
 
 //===========================================================================
 //============================= PID Settings ================================
@@ -540,7 +557,51 @@
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED
 
-#if EITHER(PIDTEMP, PIDTEMPBED)
+//===========================================================================
+//==================== PID > Chamber Temperature Control ====================
+//===========================================================================
+
+/**
+ * PID Chamber Heating
+ *
+ * If this option is enabled set PID constants below.
+ * If this option is disabled, bang-bang will be used and CHAMBER_LIMIT_SWITCHING will enable
+ * hysteresis.
+ *
+ * The PID frequency will be the same as the extruder PWM.
+ * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz,
+ * which is fine for driving a square wave into a resistive load and does not significantly
+ * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 200W
+ * heater. If your configuration is significantly different than this and you don't understand
+ * the issues involved, don't use chamber PID until someone else verifies that your hardware works.
+ */
+//#define PIDTEMPCHAMBER
+//#define CHAMBER_LIMIT_SWITCHING
+
+/**
+ * Max Chamber Power
+ * Applies to all forms of chamber control (PID, bang-bang, and bang-bang with hysteresis).
+ * When set to any value below 255, enables a form of PWM to the chamber heater that acts like a divider
+ * so don't use it unless you are OK with PWM on your heater. (See the comment on enabling PIDTEMPCHAMBER)
+ */
+#define MAX_CHAMBER_POWER 255 // limits duty cycle to chamber heater; 255=full current
+
+#if ENABLED(PIDTEMPCHAMBER)
+  #define MIN_CHAMBER_POWER 0
+  //#define PID_CHAMBER_DEBUG // Sends debug data to the serial port.
+
+  // Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
+  // and placed inside the small Creality printer enclosure tent.
+  //
+  #define DEFAULT_chamberKp 37.04
+  #define DEFAULT_chamberKi 1.40
+  #define DEFAULT_chamberKd 655.17
+  // M309 P37.04 I1.04 D655.17
+
+  // FIND YOUR OWN: "M303 E-2 C8 S50" to run autotune on the chamber at 50 degreesC for 8 cycles.
+#endif // PIDTEMPCHAMBER
+
+#if ANY(PIDTEMP, PIDTEMPBED, PIDTEMPCHAMBER)
   //#define PID_DEBUG             // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
   //#define PID_OPENLOOP          // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
@@ -587,6 +648,7 @@
 #define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
 #define THERMAL_PROTECTION_BED     // Enable thermal protection for the heated bed
 //#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber
+#define THERMAL_PROTECTION_COOLER  // Enable thermal protection for the laser cooling
 
 //===========================================================================
 //============================= Mechanical Settings =========================
@@ -999,13 +1061,13 @@
 #define PROBING_MARGIN 3
 
 // X and Y axis travel speed (mm/min) between probes
-#define XY_PROBE_SPEED (100*60)
+#define XY_PROBE_FEEDRATE (100*60)
 
 // Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_SPEED_FAST (4*60)
+#define Z_PROBE_FEEDRATE_FAST (4*60)
 
 // Feedrate (mm/min) for the "accurate" probe of each point
-#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
+#define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 2)
 
 /**
  * Probe Activation Switch
@@ -1090,6 +1152,7 @@
 //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
 #if ENABLED(PROBING_HEATERS_OFF)
   //#define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
+  //#define WAIT_FOR_HOTEND         // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
 //#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
@@ -1146,7 +1209,13 @@
 
 #define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed. Also enable HOME_AFTER_DEACTIVATE for extra safety.
 #define HOME_AFTER_DEACTIVATE   // Require rehoming after steppers are deactivated. Also enable NO_MOTION_BEFORE_HOMING for extra safety.
-//#define UNKNOWN_Z_NO_RAISE      // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
+
+/**
+ * Set Z_IDLE_HEIGHT if the Z-Axis moves on its own when steppers are disabled.
+ *  - Use a low value (i.e., Z_MIN_POS) if the nozzle falls down to the bed.
+ *  - Use a large value (i.e., Z_MAX_POS) if the bed falls down, away from the nozzle.
+ */
+//#define Z_IDLE_HEIGHT Z_HOME_POS
 
 //#define Z_HOMING_HEIGHT  4      // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                                   // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
@@ -1223,6 +1292,8 @@
   #define FIL_RUNOUT_STATE     LOW        // Pin state indicating that filament is NOT present.
   #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
+  //#define WATCH_ALL_RUNOUT_SENSORS      // Execute runout script on any triggering sensor, not only for the active extruder.
+                                          // This is automatically enabled for MIXING_EXTRUDERs.
 
   // Override individually if the runout sensors vary
   //#define FIL_RUNOUT1_STATE LOW
@@ -1257,8 +1328,9 @@
   //#define FIL_RUNOUT8_PULLUP
   //#define FIL_RUNOUT8_PULLDOWN
 
-  // Set one or more commands to execute on filament runout.
-  // (After 'M412 H' Marlin will ask the host to handle the process.)
+  // Commands to execute on filament runout.
+  // With multiple runout sensors use the %c placeholder for the current tool in commands (e.g., "M600 T%c")
+  // NOTE: After 'M412 H1' the host handles filament runout and this script does not apply.
   #define FILAMENT_RUNOUT_SCRIPT "M600"
 
   // After a runout is detected, continue printing this length of filament
@@ -1363,10 +1435,11 @@
   //#define G26_MESH_VALIDATION
   #if ENABLED(G26_MESH_VALIDATION)
     #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
-    #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for the G26 Mesh Validation Tool.
-    #define MESH_TEST_HOTEND_TEMP  205    // (°C) Default nozzle temperature for the G26 Mesh Validation Tool.
-    #define MESH_TEST_BED_TEMP      55    // (°C) Default bed temperature for the G26 Mesh Validation Tool.
-    #define G26_XY_FEEDRATE         20    // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool.
+    #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for G26.
+    #define MESH_TEST_HOTEND_TEMP  205    // (°C) Default nozzle temperature for G26.
+    #define MESH_TEST_BED_TEMP      60    // (°C) Default bed temperature for G26.
+    #define G26_XY_FEEDRATE         20    // (mm/s) Feedrate for G26 XY moves.
+    #define G26_XY_FEEDRATE_TRAVEL 100    // (mm/s) Feedrate for G26 XY travel moves.
     #define G26_RETRACT_MULTIPLIER   1.0  // G26 Q (retraction) used by default between mesh test elements.
   #endif
 
@@ -1619,15 +1692,19 @@
 
 // @section temperature
 
-// Preheat Constants
+//
+// Preheat Constants - Up to 5 are supported without changes
+//
 #define PREHEAT_1_LABEL       "PLA"
 #define PREHEAT_1_TEMP_HOTEND 205
 #define PREHEAT_1_TEMP_BED     55
+#define PREHEAT_1_TEMP_CHAMBER 35
 #define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "PETG"
 #define PREHEAT_2_TEMP_HOTEND 240
 #define PREHEAT_2_TEMP_BED     70
+#define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 /**
@@ -1952,6 +2029,14 @@
 //
 //#define REPRAP_DISCOUNT_SMART_CONTROLLER
 
+//
+// GT2560 (YHCB2004) LCD Display
+//
+// Requires Testato, Koepel softwarewire library and
+// Andriy Golovnya's LiquidCrystal_AIP31068 library.
+//
+//#define YHCB2004
+
 //
 // Original RADDS LCD Display+Encoder+SDCardReader
 // http://doku.radds.org/dokumentation/lcd-display/
@@ -2281,6 +2366,7 @@
 //#define DGUS_LCD_UI_ORIGIN
 //#define DGUS_LCD_UI_FYSETC
 //#define DGUS_LCD_UI_HIPRECY
+//#define DGUS_LCD_UI_MKS
 
 //
 // CR-6 OEM touch screen. A DWIN display with touch.
@@ -2467,6 +2553,10 @@
   //#define TOUCH_OFFSET_Y        257
   //#define TOUCH_ORIENTATION TOUCH_LANDSCAPE
 
+  #if BOTH(TOUCH_SCREEN_CALIBRATION, EEPROM_SETTINGS)
+    #define TOUCH_CALIBRATION_AUTO_SAVE // Auto save successful calibration values to EEPROM
+  #endif
+
   #if ENABLED(TFT_COLOR_UI)
     //#define SINGLE_TOUCH_NAVIGATION
   #endif
@@ -2583,6 +2673,7 @@
   // Use a single NeoPixel LED for static (background) lighting
   //#define NEOPIXEL_BKGD_LED_INDEX  0               // Index of the LED to use
   //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W
+  //#define NEOPIXEL_BKGD_ALWAYS_ON                  // Keep the backlight on when other NeoPixels are off
 #endif
 
 /**