Merge branch 'pr/23' into 2.0.x

.github/workflows/test-builds.yml

@@ -29,30 +29,31 @@ jobs:
         - DUE
         - esp32
         - linux_native
-        - megaatmega2560
+        - mega2560
         - teensy31
         - teensy35
         - SAMD51_grandcentral_m4
 
         # Extended AVR Environments
 
         - FYSETC_F6_13
-        - megaatmega1280
+        - mega1280
         - rambo
-        - sanguino_atmega1284p
-        - sanguino_atmega644p
+        - sanguino1284p
+        - sanguino644p
 
         # Extended STM32 Environments
 
-        - STM32F103RC_bigtree
-        - STM32F103RC_bigtree_USB
-        - STM32F103RE_bigtree
-        - STM32F103RE_bigtree_USB
+        - STM32F103RC_btt
+        - STM32F103RC_btt_USB
+        - STM32F103RE_btt
+        - STM32F103RE_btt_USB
         - STM32F103RC_fysetc
         - jgaurora_a5s_a1
         - STM32F103VE_longer
         - STM32F407VE_black
         - BIGTREE_SKR_PRO
+        - BIGTREE_GTR_V1_0
         - mks_robin
         - ARMED
         - FYSETC_S6

Marlin/Configuration.h

@@ -36,7 +36,7 @@
  * Advanced settings can be found in Configuration_adv.h
  *
  */
-#define CONFIGURATION_H_VERSION 020004
+#define CONFIGURATION_H_VERSION 020005
 
 //===========================================================================
 //============================= Getting Started =============================
@@ -99,6 +99,7 @@
 /**
  * Select the serial port on the board to use for communication with the host.
  * This allows the connection of wireless adapters (for instance) to non-default port pins.
+ * Serial port -1 is the USB emulated serial port, if available.
  * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader.
  *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
@@ -107,9 +108,6 @@
 
 /**
  * Select a secondary serial port on the board to use for communication with the host.
- * This allows the connection of wireless adapters (for instance) to non-default port pins.
- * Serial port -1 is the USB emulated serial port, if available.
- *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
 //#define SERIAL_PORT_2 -1
@@ -363,6 +361,7 @@
  *   331 : (3.3V scaled thermistor 1 table for MEGA)
  *   332 : (3.3V scaled thermistor 1 table for DUE)
  *     2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup)
+ *   202 : 200k thermistor - Copymaster 3D
  *     3 : Mendel-parts thermistor (4.7k pullup)
  *     4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !!
  *     5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup)
@@ -474,7 +473,7 @@
 #if ENABLED(PIDTEMP)
   //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
   //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
-  //#define PID_DEBUG             // Sends debug data to the serial port.
+  //#define PID_DEBUG             // Sends debug data to the serial port. Use 'M303 D' to toggle activation.
   //#define PID_OPENLOOP 1        // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
   //#define SLOW_PWM_HEATERS      // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
@@ -925,6 +924,14 @@
   #define SMART_EFFECTOR_MOD_PIN  -1  // Connect a GPIO pin to the Smart Effector MOD pin
 #endif
 
+/**
+ * Use StallGuard2 to probe the bed with the nozzle.
+ * Requires stallGuard-capable Trinamic stepper drivers.
+ * CAUTION: This can damage machines with Z lead screws.
+ *          Take extreme care when setting up this feature.
+ */
+//#define SENSORLESS_PROBING
+
 //
 // For Z_PROBE_ALLEN_KEY see the Delta example configurations.
 //
@@ -1438,6 +1445,7 @@
 //#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of PROGMEM. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
+#define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
 #if ENABLED(EEPROM_SETTINGS)
   //#define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
 #endif

Marlin/Configuration_adv.h

@@ -31,7 +31,7 @@
  * Basic settings can be found in Configuration.h
  *
  */
-#define CONFIGURATION_ADV_H_VERSION 020004
+#define CONFIGURATION_ADV_H_VERSION 020005
 
 // @section temperature
 
@@ -276,8 +276,10 @@
   #define AUTOTEMP_OLDWEIGHT 0.98
 #endif
 
-// Show extra position information with 'M114 D'
-//#define M114_DETAIL
+// Extra options for the M114 "Current Position" report
+//#define M114_DETAIL         // Use 'M114` for details to check planner calculations
+//#define M114_REALTIME       // Real current position based on forward kinematics
+//#define M114_LEGACY         // M114 used to synchronize on every call. Enable if needed.
 
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
@@ -336,15 +338,22 @@
  * Controller Fan
  * To cool down the stepper drivers and MOSFETs.
  *
- * The fan will turn on automatically whenever any stepper is enabled
- * and turn off after a set period after all steppers are turned off.
+ * The fan turns on automatically whenever any driver is enabled and turns
+ * off (or reduces to idle speed) shortly after drivers are turned off.
+ *
  */
 //#define USE_CONTROLLER_FAN
 #if ENABLED(USE_CONTROLLER_FAN)
-  //#define CONTROLLER_FAN_PIN -1           // Set a custom pin for the controller fan
-  #define CONTROLLERFAN_SECS 60             // Duration in seconds for the fan to run after all motors are disabled
-  #define CONTROLLERFAN_SPEED 255           // 255 == full speed
-  //#define CONTROLLERFAN_SPEED_Z_ONLY 127  // Reduce noise on machines that keep Z enabled
+  //#define CONTROLLER_FAN_PIN -1        // Set a custom pin for the controller fan
+  //#define CONTROLLER_FAN_USE_Z_ONLY    // With this option only the Z axis is considered
+  #define CONTROLLERFAN_SPEED_MIN      0 // (0-255) Minimum speed. (If set below this value the fan is turned off.)
+  #define CONTROLLERFAN_SPEED_ACTIVE 255 // (0-255) Active speed, used when any motor is enabled
+  #define CONTROLLERFAN_SPEED_IDLE     0 // (0-255) Idle speed, used when motors are disabled
+  #define CONTROLLERFAN_IDLE_TIME     60 // (seconds) Extra time to keep the fan running after disabling motors
+  //#define CONTROLLER_FAN_EDITABLE      // Enable M710 configurable settings
+  #if ENABLED(CONTROLLER_FAN_EDITABLE)
+    #define CONTROLLER_FAN_MENU          // Enable the Controller Fan submenu
+  #endif
 #endif
 
 // When first starting the main fan, run it at full speed for the
@@ -716,6 +725,9 @@
   #define Z_STEPPER_ALIGN_ITERATIONS 5    // Number of iterations to apply during alignment
   #define Z_STEPPER_ALIGN_ACC        0.02 // Stop iterating early if the accuracy is better than this
   #define RESTORE_LEVELING_AFTER_G34      // Restore leveling after G34 is done?
+  // After G34, re-home Z (G28 Z) or just calculate it from the last probe heights?
+  // Re-homing might be more precise in reproducing the actual 'G28 Z' homing height, especially on an uneven bed.
+  #define HOME_AFTER_G34
 #endif
 
 // @section motion
@@ -748,8 +760,12 @@
 // Minimum time that a segment needs to take if the buffer is emptied
 #define DEFAULT_MINSEGMENTTIME        20000   // (ms)
 
-// If defined the movements slow down when the look ahead buffer is only half full
+// Slow down the machine if the look ahead buffer is (by default) half full.
+// Increase the slowdown divisor for larger buffer sizes.
 #define SLOWDOWN
+#if ENABLED(SLOWDOWN)
+  #define SLOWDOWN_DIVISOR 2
+#endif
 
 // Frequency limit
 // See nophead's blog for more info
@@ -990,7 +1006,11 @@
 // Show the E position (filament used) during printing
 //#define LCD_SHOW_E_TOTAL
 
-#if HAS_GRAPHICAL_LCD && HAS_PRINT_PROGRESS
+#if ENABLED(SHOW_BOOTSCREEN)
+  #define BOOTSCREEN_TIMEOUT 4000        // (ms) Total Duration to display the boot screen(s)
+#endif
+
+#if HAS_GRAPHICAL_LCD && EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY)
   //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits
   //#define SHOW_REMAINING_TIME          // Display estimated time to completion
   #if ENABLED(SHOW_REMAINING_TIME)
@@ -999,7 +1019,7 @@
   #endif
 #endif
 
-#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
+#if HAS_CHARACTER_LCD && EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY)
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
   #if ENABLED(LCD_PROGRESS_BAR)
     #define PROGRESS_BAR_BAR_TIME 2000    // (ms) Amount of time to show the bar
@@ -1012,12 +1032,9 @@
 
 #if ENABLED(SDSUPPORT)
 
-  // Some RAMPS and other boards don't detect when an SD card is inserted. You can work
-  // around this by connecting a push button or single throw switch to the pin defined
-  // as SD_DETECT_PIN in your board's pins definitions.
-  // This setting should be disabled unless you are using a push button, pulling the pin to ground.
-  // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER).
-  #define SD_DETECT_INVERTED
+  // The standard SD detect circuit reads LOW when media is inserted and HIGH when empty.
+  // Enable this option and set to HIGH if your SD cards are incorrectly detected.
+  //#define SD_DETECT_STATE HIGH
 
   #define SD_FINISHED_STEPPERRELEASE true          // Disable steppers when SD Print is finished
   #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place.
@@ -1032,16 +1049,24 @@
 
   #define EVENT_GCODE_SD_STOP "G28XY"       // G-code to run on Stop Print (e.g., "G28XY" or "G27")
 
+  #if ENABLED(PRINTER_EVENT_LEDS)
+    #define PE_LEDS_COMPLETED_TIME  (30*60) // (seconds) Time to keep the LED "done" color before restoring normal illumination
+  #endif
+
   /**
    * Continue after Power-Loss (Creality3D)
    *
    * Store the current state to the SD Card at the start of each layer
    * during SD printing. If the recovery file is found at boot time, present
    * an option on the LCD screen to continue the print from the last-known
    * point in the file.
+   *
+   * If the machine reboots when resuming a print you may need to replace or
+   * reformat the SD card. (Bad sectors delay startup triggering the watchdog.)
    */
   //#define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
+    #define PLR_ENABLED_DEFAULT   false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
     //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
     //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
@@ -1221,10 +1246,6 @@
   // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
   //#define USE_SMALL_INFOFONT
 
-  // Enable this option and reduce the value to optimize screen updates.
-  // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
-  //#define DOGM_SPI_DELAY_US 5
-
   // Swap the CW/CCW indicators in the graphics overlay
   //#define OVERLAY_GFX_REVERSE
 
@@ -1241,6 +1262,10 @@
    * This will prevent position updates from being displayed.
    */
   #if ENABLED(U8GLIB_ST7920)
+    // Enable this option and reduce the value to optimize screen updates.
+    // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
+    //#define DOGM_SPI_DELAY_US 5
+
     //#define LIGHTWEIGHT_UI
     #if ENABLED(LIGHTWEIGHT_UI)
       #define STATUS_EXPIRE_SECONDS 20
@@ -1278,24 +1303,23 @@
 // Additional options for DGUS / DWIN displays
 //
 #if HAS_DGUS_LCD
-  #define DGUS_SERIAL_PORT 2
+  #define DGUS_SERIAL_PORT 3
   #define DGUS_BAUDRATE 115200
 
   #define DGUS_RX_BUFFER_SIZE 128
   #define DGUS_TX_BUFFER_SIZE 48
   //#define DGUS_SERIAL_STATS_RX_BUFFER_OVERRUNS  // Fix Rx overrun situation (Currently only for AVR)
 
   #define DGUS_UPDATE_INTERVAL_MS  500    // (ms) Interval between automatic screen updates
-  #define BOOTSCREEN_TIMEOUT      3000    // (ms) Duration to display the boot screen
 
   #if EITHER(DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_HIPRECY)
     #define DGUS_PRINT_FILENAME           // Display the filename during printing
     #define DGUS_PREHEAT_UI               // Display a preheat screen during heatup
 
     #if ENABLED(DGUS_LCD_UI_FYSETC)
-      //#define DUGS_UI_MOVE_DIS_OPTION   // Disabled by default for UI_FYSETC
+      //#define DGUS_UI_MOVE_DIS_OPTION   // Disabled by default for UI_FYSETC
     #else
-      #define DUGS_UI_MOVE_DIS_OPTION     // Enabled by default for UI_HIPRECY
+      #define DGUS_UI_MOVE_DIS_OPTION     // Enabled by default for UI_HIPRECY
     #endif
 
     #define DGUS_FILAMENT_LOADUNLOAD
@@ -1578,7 +1602,7 @@
   #if ENABLED(PROBE_TEMP_COMPENSATION)
     // Max temperature that can be reached by heated bed.
     // This is required only for the calibration process.
-    #define PTC_MAX_BED_TEMP 110
+    #define PTC_MAX_BED_TEMP BED_MAXTEMP
 
     // Park position to wait for probe cooldown
     #define PTC_PARK_POS_X 0.0F
@@ -2015,7 +2039,7 @@
  * TMCStepper library is required to use TMC stepper drivers.
  * https://github.com/teemuatlut/TMCStepper
  */
-#if HAS_TRINAMIC
+#if HAS_TRINAMIC_CONFIG
 
   #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
   #define INTERPOLATE       true  // Interpolate X/Y/Z_MICROSTEPS to 256
@@ -2302,14 +2326,6 @@
    */
   //#define SENSORLESS_HOMING // StallGuard capable drivers only
 
-  /**
-   * Use StallGuard2 to probe the bed with the nozzle.
-   *
-   * CAUTION: This could cause damage to machines that use a lead screw or threaded rod
-   *          to move the Z axis. Take extreme care when attempting to enable this feature.
-   */
-  //#define SENSORLESS_PROBING // StallGuard capable drivers only
-
   #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
     // TMC2209: 0...255. TMC2130: -64...63
     #define X_STALL_SENSITIVITY  8
@@ -2345,7 +2361,7 @@
    */
   #define TMC_ADV() {  }
 
-#endif // HAS_TRINAMIC
+#endif // HAS_TRINAMIC_CONFIG
 
 // @section L64XX
 
@@ -2991,7 +3007,7 @@
   #define MAX7219_LOAD_PIN  44
 
   //#define MAX7219_GCODE          // Add the M7219 G-code to control the LED matrix
-  #define MAX7219_INIT_TEST    2   // Do a test pattern at initialization (Set to 2 for spiral)
+  #define MAX7219_INIT_TEST    2   // Test pattern at startup: 0=none, 1=sweep, 2=spiral
   #define MAX7219_NUMBER_UNITS 1   // Number of Max7219 units in chain.
   #define MAX7219_ROTATE       0   // Rotate the display clockwise (in multiples of +/- 90°)
                                    // connector at:  right=0   bottom=-90  top=90  left=180

Marlin/Makefile

@@ -267,6 +267,8 @@ else ifeq ($(HARDWARE_MOTHERBOARD),1147)
 else ifeq ($(HARDWARE_MOTHERBOARD),1148)
 # MKS GEN L V2
 else ifeq ($(HARDWARE_MOTHERBOARD),1149)
+# Copymaster 3D
+else ifeq ($(HARDWARE_MOTHERBOARD),1150)
 
 #
 # RAMBo and derivatives

Marlin/Version.h

@@ -28,11 +28,7 @@
 /**
  * Marlin release version identifier
  */
-<<<<<<< HEAD
-//#define SHORT_BUILD_VERSION "2.0.2"
-=======
-//#define SHORT_BUILD_VERSION "2.0.4.4"
->>>>>>> pr/19
+//#define SHORT_BUILD_VERSION "2.0.5.3"
 
 /**
  * Verbose version identifier which should contain a reference to the location
@@ -45,11 +41,6 @@
  * here we define this default string as the date where the latest release
  * version was tagged.
  */
-<<<<<<< HEAD
-//#define STRING_DISTRIBUTION_DATE "2020-01-27"
-=======
-//#define STRING_DISTRIBUTION_DATE "2020-01-31"
->>>>>>> pr/19
 
 /**
  * Defines a generic printer name to be output to the LCD after booting Marlin.

Marlin/src/HAL/HAL_AVR/HAL_SPI.cpp → Marlin/src/HAL/AVR/HAL_SPI.cpp

@@ -197,7 +197,7 @@ void spiBegin() {
     // output pin high - like sending 0xFF
     WRITE(MOSI_PIN, HIGH);
 
-    for (uint8_t i = 0; i < 8; i++) {
+    LOOP_L_N(i, 8) {
       WRITE(SCK_PIN, HIGH);
 
       nop; // adjust so SCK is nice
@@ -224,7 +224,7 @@ void spiBegin() {
   void spiSend(uint8_t data) {
     // no interrupts during byte send - about 8µs
     cli();
-    for (uint8_t i = 0; i < 8; i++) {
+    LOOP_L_N(i, 8) {
       WRITE(SCK_PIN, LOW);
       WRITE(MOSI_PIN, data & 0x80);
       data <<= 1;