This project simulates the Arlo Basestation to communicate with cameras.
Based on reconstructing the communication between a VMB4000r3 and Arlo Pro 2 cameras.
It won't work with the mobile app, and there is no real plan to support this at present. However, it does allow you to use your Arlo cameras as normal RTSP camera sources for other media recorders.
We can either emulate the basestation using the same SSID and capture and re-use the WPA-PSK to make the cameras connect to us. Or we can try and use WPS to get the cameras to sync to our own basestation.
Currently running this on a Raspberry Pi 1b with a TP-Link TL-WN722N USB WiFi adapter.
Tested working on Raspberry Pi OS Lite released 2nd December 2020:
sudo apt install -y python3-pip vlc
pip3 install -r requirements.txt
There is also a script to setup the Pi with hostapd/dnsmasq and configure the server within systemd. Should work well on a fresh Raspberry Pi - remember to chagne the PSK first.
python3 server.py
The service spins up a REST API on TCP port 5000. The api.postman_collection.json config contains all of the functioning endpoints to import into Postman.
I've put a basic webhook in to trigger when motion is detected. This needs further work to capture more events.
A camera on battery power reports near ambient temperatures for it's temperature, although I haven't measured quite how big the difference is. This can be retrieved with a status request via the API.
To get the cameras to connect to us we can capture the WPA-PSK using WPS Push Button with the following configuration:
wpa.conf:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
update_config=1
device_name=NTGRDEV
manufacturer=broadcom technology, Inc.
Then run the following commands and press the button on the base station or use the app to put it into pairing mode:
systemctl stop NetworkManager.service
wpa_supplicant -t -Dwext -i wlan0 -c wpa.conf
iwconfig wlan0 essid NETGEAR05
wpa_cli -i wlan0 wps_pbc
If successful the wpa.conf should contain the WPA-PSK and you can configure your own wireless network with the same ESSID and key.
The cameras seem fairly happy to connect to any basestation when they the 'Sync' button is pressed. With hostapd the following configuration was used:
beacon_int=100
ssid=NETGEAR07
interface=wlan0
channel=1
ctrl_interface=/var/run/hostapd
wpa_passphrase=YOUR_PSK_HERE
ctrl_interface_group=0
eap_server=1
wps_pin_requests=/var/run/hostapd.pin-req
config_methods=label display push_button keypad
wps_state=2
ap_setup_locked=1
ieee80211n=1
ignore_broadcast_ssid=0
PBC can be activated using:
hostapd_cli wps_pbc
The FFmpeg library doesn't send RTCP Response Received messages very often, and the camera seems to timeout the stream, and force itself to reauth to the wifi if this happens. This means FFmpeg and dependent apps seem to kill the camera after about 6seconds. libVLC seems to work, also Live555 - openRTSP.
Blocking ALL RTCP (by dropping all UDP) appears to allow FFMPEG to function, as the cameras dont mind if no RTCP responses are received. However, if the connection dies without a TEARDOWN from the client then the cameras may just keep sending RTP packets and may require a reboot as they don't know the client has disconnected.
The UDP port 5000 on the cameras constantly listens for RTP traffic with the following encoding:
Audio: pcm_mulaw, 8000 Hz, mono, s16, 64 kb/s
ffmpeg -re -i piano2.wav -ar 8000 -sample_fmt s16 -ac 1 -f rtp rtp://172.14.1.194:5000
ffmpeg -f alsa -channels 1 -i hw:1 -ar 8000 -sample_fmt s16 -ac 1 -f rtp rtp://172.14.1.194:5000
Where hw:1 matches source input hardware device etc
Sending audio whilst the camera is streaming appears to kill audio...
