This is a guide for installing Debian GNU/Linux on a Pogoplug Pro.
All of this was gathered from other sources. The only thing I made is this readme file.
- noisebridge wiki page
- doozan forum u-boot page
- doozan forum rootfs and kernel page
- serial console pinout source
You can use an old-school CD-ROM to soundcard cable or a Seeed studio groove connector. I'm not sure what the actual names of these are. When looking at the board with the text printed on the circuit board right-side up, the pins left to right are:
Ground, RX, TX, VCC
It's using 3.3 V 115200 8n1.
The serial console drops you straight into a root shell with no password prompt.
Set root password:
passwd
Make a note of the MAC address. You'll need it later. It can also be found on the label under the PogoPlug device:
ifconfig eth0
You're looking for something like:
ether 12:3b:54:af:43:11
or:
HWaddr 12:3b:54:af:43:11
Check for bad blocks:
dmesg | grep -i 'bad'
If you see a bad block in the first 2 MB then do not proceed. That would look something like this:
[ 2.413231] Scanning device for bad blocks
[ 2.417731] Bad eraseblock 3 at 0x000000060000
Start dropbear:
/etc/init.d/dropbear.sh start
Either run a DHCP server (like dnsmasq) on your computer and look for the DHCP lease to see the PogoPlug's IP:
tail -f /var/log/syslog
Then connect via ethernet and the IP show up in the log. Or you can set a static IP on the PogoPlug with ifconfig:
ifconfig eth0 192.168.1.2 netmask 255.255.255.0 up
Now scp the uboot image:
scp uboot.2015.10-tld-2.ox820.bodhi.tar [email protected]:/tmp/
Create the file /etc/fw_env.config with the following content:
# pogoplug v3
/dev/mtd1 0x00100000 0x20000 0x20000
Extract the uboot archive:
cd /tmp
tar xvf uboot.2015.10-tld-2.ox820.bodhi.tar
Erase 6 blocks on mtd1:
/usr/sbin/flash_erase /dev/mtd1 0x0 6
Expected output:
Erase Total 6 Units
Performing Flash Erase of length 131072 at offset 0xa0000 done
Flash encoded spl stage1 to 0x0:
/usr/sbin/nandwrite /dev/mtd1 uboot.spl.2013.10.ox820.850mhz.mtd0.img
Expected output:
Writing data to block 0 at offset 0x0
Flash uboot to 0x40000:
/usr/sbin/nandwrite -s 262144 /dev/mtd1 uboot.2015.10-tld-2.ox820.mtd0.img
Expected output:
Writing data to block 2 at offset 0x40000
Writing data to block 3 at offset 0x60000
Writing data to block 4 at offset 0x80000
Writing data to block 5 at offset 0xa0000
Erase 1 block starting 0x00100000:
/usr/sbin/flash_erase /dev/mtd1 0x00100000 1
Expected output:
Erase Total 1 Units
Performing Flash Erase of length 131072 at offset 0x100000 done
Flash uboot environment to 0x00100000
/usr/sbin/nandwrite -s 1048576 /dev/mtd1 uboot.2015.10-tld-2.ox820.environment.img
Expected output:
Writing data to block 8 at offset 0x100000
You're now done flashing the new uboot.
On your computer get a USB stick and create a single Linux partition on it. (e.g. use fdisk /dev/sdX then d to delete each partition, then n to create a new partition which will automatically created as a Linux partition, then w to write the changed).
Then format the partition with an ext4 filesystem labeled 'rootfs' (this is important):
sudo mkfs.ext4 -L rootfs /dev/sdX1
Mount the partition:
sudo mount /dev/sdX1 /mnt
Download the rootfs archive from the releases page of this repository or just click this link.
Extract the rootfs archive:
cd /mnt
sudo tar xvjf /path/to/Debian-4.4.54-oxnas-tld-1-rootfs-bodhi.tar.bz2
Adjust the rootfs line in fstab by editing /mnt/etc/fstab, changing 'ext3' to 'ext4':
LABEL=rootfs / ext4 noatime,errors=remount-ro 0 1
Unmount:
cd /
sudo umount /mnt
Plug the usb stick into your PogoPlug and reboot it.
It should boot into Debian and ask you to log in. The default credentials are:
username: root
password: root
The first thing to do is generate an ssh key:
rm /etc/ssh/ssh_host*
ssh-keygen -A
You might run out of ram during the next step, so first stop a few running services:
/etc/init.d/ssh stop
/etc/init.d/avahi-daemon stop
Ensure you have an internet connection (plug the ethernet cable into something appropriate) then:
apt-get update
apt-get upgrade
Set the correct MAC address. This is the address you wrote down earlier. If you didn't, it should be written on the label under the PogoPlug device:
fw_setenv ethaddr 12:3b:54:af:43:11
From your compter, scp the kernel to the PogoPlug:
scp linux-4.4.124-oxnas-tld-1.bodhi.tar.bz2 [email protected]:/boot/
On the PogoPlug, extract the files:
cd /boot
tar xvjf linux-4.4.124-oxnas-tld-1.bodhi.tar.bz2
tar xf linux-dtb-4.4.124-oxnas-tld-1.tar
Install the new kernel:
dpkg -i linux-image-4.4.124-oxnas-tld-1_1.0_armel.deb
Backup old uImage and uInitrd:
mv uImage uImage.bak
mv uInitrd uInitrd.bak
Create new uImage and uInitrd:
mkimage -A arm -O linux -T kernel -C none -a 0x60008000 -e 0x60008000 -n Linux-4.4.124-oxnas-tld-1 -d vmlinuz-4.4.124-oxnas-tld-1 uImage
mkimage -A arm -O linux -T ramdisk -C gzip -a 0x60000000 -e 0x60000000 -n initramfs-4.4.124-oxnas-tld-1 -d initrd.img-4.4.124-oxnas-tld-1 uInitrd
Clean up:
rm *.deb
rm *.tar
rm *.tar.bz2
Sync the filesystem:
sync
Now reboot:
reboot
That's it!
The wifi adapter needs a closed firmware.
To get the wifi working, add the following line to /etc/apt/sources.list:
deb http://ftp.us.debian.org/debian stretch main non-free
Then run:
apt update
Then install lspci and iw:
apt install pciutils iw
Run lspci:
lspci
If you have a Ralink RT3090 you should do:
apt install firmware-misc-nonfree
If you have an RT8xxx card you shoul do:
apt install firmware-realtek
You can install both if you're not sure.
Now you'll need a few more packages:
apt install wpasupplicant hostapd bridge-utils wireless-tools iw
If you want to use the wifi card as a client, edit /etc/network/interfaces adding the wollowing:
auto wlp0s0
iface wlp0s0 inet dhcp
wpa-ssid your_wifi_ssid
wpa-psk your_wifi_password
or if your wifi has no password you can use:
auto wlp0s0
iface wlp0s0 inet dhcp
wireless-essid your_wifi_ssid
Don't put quotes around the ssid or password, not even if it has spaces.
Then test it with:
ifup -v wlp0s0
Install the vsftpd sever:
sudo apt install vsftpd
Use the vsftpd.conf from this git repo:
sudo cp ./vsftpd.conf /etc/
The directory shared via ftp will be /srv/ftp. You can change this by altering the ftp users' home directory in /etc/passwd.
If you want to share an external drive then first partition it, then format it and give it a unique label. Let's assume it's called /dev/sdb.
WARNING THE FOLLOWING WILL DELETE EVERYTHIN ON THE DRIVE
To partition run sudo fdisk /dev/sdb, then hit d and enter again until there are no partitions left. Now hit c to create a partition and hit enter for each question to accept the defaults, then hit w to write the changes to disk.
Now format the drive:
# WARNING THIS WILL DELETE EVERYTHINg ON THE DRIVE
sudo mkfs.ext4 -L my-labeled-drive /dev/sdb1
To make the drive automatically mount in the ftp directory on boot add the following line to /etc/fstab:
LABEL=my-labeled-drive /srv/ftp ext4 noatime,errors=remount-ro 0 2
Now mount it to ensure that the fstab line works:
sudo mount /srv/ftp
While the drive is mounted, set the permissions:
sudo chown root.ftp /srv/ftp
sudo chmod 755 /srv/ftp
If you want users to be able to upload to an uploads directory then do:
sudo mkdir /srv/ftp/uploads
sudo chown ftp.ftp /srv/ftp/uploads
sudo chmod 755 /srv/ftp/uploads
by default no-one will be able to delete from the uploads/ directory. To change this modify the line in /etc/vsftpd.conf saying chown_uploads=YES to chown_uploads=NO. Note that this will allow anyone to delete anything in the uploads directory.
Now restart vsftpd to make it use the new configuration:
sudo /etc/init.d/vsftpd restart
Create a test file to download:
sudo echo "Welcome to my ftp server!" > /srv/ftp/README
Test that you can connect to the ftp server using e.g. ncftp from another computer and download and upload
sudo apt install ncftp
echo "TEST UPLOAD CONTENT" > test
ncftp <ip_address_of_pogogplug>
get README
cd uploads/
put test