Fix the codebase

Marlin/Configuration.h

@@ -266,7 +266,7 @@
  */
 //#define MAGNETIC_PARKING_EXTRUDER
 
-#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
+#if ANY(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER)
 
   #define PARKING_EXTRUDER_PARKING_X { -78, 184 }     // X positions for parking the extruders
   #define PARKING_EXTRUDER_GRAB_DISTANCE 1            // (mm) Distance to move beyond the parking point to grab the extruder
@@ -419,7 +419,7 @@
     #define POWER_TIMEOUT              30 // (s) Turn off power if the machine is idle for this duration
     //#define POWER_OFF_DELAY          60 // (s) Delay of poweroff after M81 command. Useful to let fans run for extra time.
   #endif
-  #if EITHER(AUTO_POWER_CONTROL, POWER_OFF_WAIT_FOR_COOLDOWN)
+  #if ANY(AUTO_POWER_CONTROL, POWER_OFF_WAIT_FOR_COOLDOWN)
     //#define AUTO_POWER_E_TEMP        50 // (°C) PSU on if any extruder is over this temperature
     //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) PSU on if the chamber is over this temperature
     //#define AUTO_POWER_COOLER_TEMP   26 // (°C) PSU on if the cooler is over this temperature
@@ -921,7 +921,7 @@
     #define DELTA_CALIBRATION_DEFAULT_POINTS 4
   #endif
 
-  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+  #if ANY(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
     // Step size for paper-test probing
     #define PROBE_MANUALLY_STEP 0.05      // (mm)
   #endif
@@ -965,7 +965,7 @@
  */
 //#define MORGAN_SCARA
 //#define MP_SCARA
-#if EITHER(MORGAN_SCARA, MP_SCARA)
+#if ANY(MORGAN_SCARA, MP_SCARA)
   // If movement is choppy try lowering this value
   #define DEFAULT_SEGMENTS_PER_SECOND 200
 
@@ -1809,7 +1809,7 @@
   #define MAX_SOFTWARE_ENDSTOP_W
 #endif
 
-#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
+#if ANY(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
   //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
 #endif
 
@@ -2046,7 +2046,7 @@
 
 #endif
 
-#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
+#if ANY(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
 
   // Set the number of grid points per dimension.
   #define GRID_MAX_POINTS_X 3
@@ -3340,7 +3340,7 @@
   //#define TOUCH_OFFSET_Y        257
   //#define TOUCH_ORIENTATION TOUCH_LANDSCAPE
 
-  #if BOTH(TOUCH_SCREEN_CALIBRATION, EEPROM_SETTINGS)
+  #if ALL(TOUCH_SCREEN_CALIBRATION, EEPROM_SETTINGS)
     #define TOUCH_CALIBRATION_AUTO_SAVE // Auto save successful calibration values to EEPROM
   #endif
 
@@ -3437,7 +3437,7 @@
 //#define RGB_LED
 //#define RGBW_LED
 
-#if EITHER(RGB_LED, RGBW_LED)
+#if ANY(RGB_LED, RGBW_LED)
   //#define RGB_LED_R_PIN 34
   //#define RGB_LED_G_PIN 43
   //#define RGB_LED_B_PIN 35

Marlin/Configuration_adv.h

@@ -310,7 +310,7 @@
   //#define ADAPTIVE_FAN_SLOWING              // Slow down the part-cooling fan if the temperature drops
   #if ENABLED(ADAPTIVE_FAN_SLOWING)
     //#define REPORT_ADAPTIVE_FAN_SLOWING     // Report fan slowing activity to the console
-    #if EITHER(MPCTEMP, PIDTEMP)
+    #if ANY(MPCTEMP, PIDTEMP)
       //#define TEMP_TUNING_MAINTAIN_FAN      // Don't slow down the fan speed during M303 or M306 T
     #endif
   #endif
@@ -759,10 +759,10 @@
   #if ENABLED(NEOPIXEL_LED)
     //#define CASE_LIGHT_USE_NEOPIXEL         // Use NeoPixel LED as case light
   #endif
-  #if EITHER(RGB_LED, RGBW_LED)
+  #if ANY(RGB_LED, RGBW_LED)
     //#define CASE_LIGHT_USE_RGB_LED          // Use RGB / RGBW LED as case light
   #endif
-  #if EITHER(CASE_LIGHT_USE_NEOPIXEL, CASE_LIGHT_USE_RGB_LED)
+  #if ANY(CASE_LIGHT_USE_NEOPIXEL, CASE_LIGHT_USE_RGB_LED)
     #define CASE_LIGHT_DEFAULT_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
   #endif
 #endif
@@ -1175,7 +1175,7 @@
  */
 //#define INPUT_SHAPING_X
 //#define INPUT_SHAPING_Y
-#if EITHER(INPUT_SHAPING_X, INPUT_SHAPING_Y)
+#if ANY(INPUT_SHAPING_X, INPUT_SHAPING_Y)
   #if ENABLED(INPUT_SHAPING_X)
     #define SHAPING_FREQ_X  40          // (Hz) The default dominant resonant frequency on the X axis.
     #define SHAPING_ZETA_X  0.15f       // Damping ratio of the X axis (range: 0.0 = no damping to 1.0 = critical damping).
@@ -1417,7 +1417,7 @@
  */
 //#define DIGIPOT_MCP4018             // Requires https://github.com/felias-fogg/SlowSoftI2CMaster
 //#define DIGIPOT_MCP4451
-#if EITHER(DIGIPOT_MCP4018, DIGIPOT_MCP4451)
+#if ANY(DIGIPOT_MCP4018, DIGIPOT_MCP4451)
   #define DIGIPOT_I2C_NUM_CHANNELS 8  // 5DPRINT:4   AZTEEG_X3_PRO:8   MKS_SBASE:5   MIGHTYBOARD_REVE:5
 
   // Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS.
@@ -1474,7 +1474,7 @@
 //
 //#define LCD_BACKLIGHT_TIMEOUT_MINS 1  // (minutes) Timeout before turning off the backlight
 
-#if HAS_BED_PROBE && EITHER(HAS_MARLINUI_MENU, HAS_TFT_LVGL_UI)
+#if HAS_BED_PROBE && ANY(HAS_MARLINUI_MENU, HAS_TFT_LVGL_UI)
   //#define PROBE_OFFSET_WIZARD       // Add a Probe Z Offset calibration option to the LCD menu
   #if ENABLED(PROBE_OFFSET_WIZARD)
     /**
@@ -1544,13 +1544,13 @@
   #define SHOW_BOOTSCREEN                 // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
   #if ENABLED(SHOW_BOOTSCREEN)
     #define BOOTSCREEN_TIMEOUT 3000       // (ms) Total Duration to display the boot screen(s)
-    #if EITHER(HAS_MARLINUI_U8GLIB, TFT_COLOR_UI)
+    #if ANY(HAS_MARLINUI_U8GLIB, TFT_COLOR_UI)
       #define BOOT_MARLIN_LOGO_SMALL      // Show a smaller Marlin logo on the Boot Screen (saving lots of flash)
     #endif
     #if HAS_MARLINUI_U8GLIB
       //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of flash.
     #endif
-    #if EITHER(HAS_MARLINUI_U8GLIB, TOUCH_UI_FTDI_EVE)
+    #if ANY(HAS_MARLINUI_U8GLIB, TOUCH_UI_FTDI_EVE)
       //#define SHOW_CUSTOM_BOOTSCREEN    // Show the bitmap in Marlin/_Bootscreen.h on startup.
     #endif
   #endif
@@ -1615,13 +1615,13 @@
   #define SET_REMAINING_TIME              // Add 'R' parameter to set remaining time
   //#define SET_INTERACTION_TIME          // Add 'C' parameter to set time until next filament change or other user interaction
   //#define M73_REPORT                    // Report M73 values to host
-  #if BOTH(M73_REPORT, HAS_MEDIA)
+  #if ALL(M73_REPORT, HAS_MEDIA)
     #define M73_REPORT_SD_ONLY            // Report only when printing from SD
   #endif
 #endif
 
 // LCD Print Progress options. Multiple times may be displayed in turn.
-#if HAS_DISPLAY && EITHER(HAS_MEDIA, SET_PROGRESS_MANUALLY)
+#if HAS_DISPLAY && ANY(HAS_MEDIA, SET_PROGRESS_MANUALLY)
   #define SHOW_PROGRESS_PERCENT           // Show print progress percentage (doesn't affect progress bar)
   #define SHOW_ELAPSED_TIME               // Display elapsed printing time (prefix 'E')
   //#define SHOW_REMAINING_TIME           // Display estimated time to completion (prefix 'R')
@@ -1630,7 +1630,7 @@
   #endif
   //#define PRINT_PROGRESS_SHOW_DECIMALS  // Show/report progress with decimal digits, not all UIs support this
 
-  #if EITHER(HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL)
+  #if ANY(HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL)
     //#define LCD_PROGRESS_BAR            // Show a progress bar on HD44780 LCDs for SD printing
     #if ENABLED(LCD_PROGRESS_BAR)
       #define PROGRESS_BAR_BAR_TIME 2000  // (ms) Amount of time to show the bar
@@ -2302,15 +2302,15 @@
   //#define PROBING_MARGIN_BACK PROBING_MARGIN
 #endif
 
-#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
+#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
   //#define MESH_MIN_X MESH_INSET
   //#define MESH_MIN_Y MESH_INSET
   //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
   //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
 #endif
 
-#if BOTH(AUTO_BED_LEVELING_UBL, EEPROM_SETTINGS)
+#if ALL(AUTO_BED_LEVELING_UBL, EEPROM_SETTINGS)
   //#define OPTIMIZED_MESH_STORAGE  // Store mesh with less precision to save EEPROM space
 #endif
 
@@ -2380,7 +2380,7 @@
   #endif
 
   // G76 options
-  #if BOTH(PTC_PROBE, PTC_BED)
+  #if ALL(PTC_PROBE, PTC_BED)
     // Park position to wait for probe cooldown
     #define PTC_PARK_POS   { 0, 0, 100 }
 
@@ -2422,7 +2422,7 @@
 // G5 Bézier Curve Support with XYZE destination and IJPQ offsets
 //#define BEZIER_CURVE_SUPPORT        // Requires ~2666 bytes
 
-#if EITHER(ARC_SUPPORT, BEZIER_CURVE_SUPPORT)
+#if ANY(ARC_SUPPORT, BEZIER_CURVE_SUPPORT)
   //#define CNC_WORKSPACE_PLANES      // Allow G2/G3/G5 to operate in XY, ZX, or YZ planes
 #endif
 
@@ -2508,7 +2508,7 @@
 
 // The number of linear moves that can be in the planner at once.
 // The value of BLOCK_BUFFER_SIZE must be a power of 2 (e.g., 8, 16, 32)
-#if BOTH(HAS_MEDIA, DIRECT_STEPPING)
+#if ALL(HAS_MEDIA, DIRECT_STEPPING)
   #define BLOCK_BUFFER_SIZE  8
 #elif HAS_MEDIA
   #define BLOCK_BUFFER_SIZE 16
@@ -3290,7 +3290,7 @@
    */
   //#define SENSORLESS_HOMING // StallGuard capable drivers only
 
-  #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING)
+  #if ANY(SENSORLESS_HOMING, SENSORLESS_PROBING)
     // TMC2209: 0...255. TMC2130: -64...63
     #define X_STALL_SENSITIVITY  8
     #define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY
@@ -3453,7 +3453,7 @@
  */
 //#define SPINDLE_FEATURE
 //#define LASER_FEATURE
-#if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
+#if ANY(SPINDLE_FEATURE, LASER_FEATURE)
   #define SPINDLE_LASER_ACTIVE_STATE    LOW    // Set to "HIGH" if SPINDLE_LASER_ENA_PIN is active HIGH
 
   #define SPINDLE_LASER_USE_PWM                // Enable if your controller supports setting the speed/power
@@ -4205,7 +4205,7 @@
 //#define WIFISUPPORT         // Marlin embedded WiFi management
 //#define ESP3D_WIFISUPPORT   // ESP3D Library WiFi management (https://github.com/luc-github/ESP3DLib)
 
-#if EITHER(WIFISUPPORT, ESP3D_WIFISUPPORT)
+#if ANY(WIFISUPPORT, ESP3D_WIFISUPPORT)
   //#define WEBSUPPORT          // Start a webserver (which may include auto-discovery)
   //#define OTASUPPORT          // Support over-the-air firmware updates
   //#define WIFI_CUSTOM_COMMAND // Accept feature config commands (e.g., WiFi ESP3D) from the host

Marlin/src/HAL/AVR/MarlinSerial.h

@@ -280,7 +280,7 @@
     static constexpr bool DROPPED_RX        = false;
     static constexpr bool RX_FRAMING_ERRORS = false;
     static constexpr bool MAX_RX_QUEUED     = false;
-    static constexpr bool RX_OVERRUNS       = BOTH(HAS_DGUS_LCD, SERIAL_STATS_RX_BUFFER_OVERRUNS);
+    static constexpr bool RX_OVERRUNS       = ALL(HAS_DGUS_LCD, SERIAL_STATS_RX_BUFFER_OVERRUNS);
   };
 
   typedef Serial1Class< MarlinSerial< LCDSerialCfg<LCD_SERIAL_PORT> > > MSerialLCD;

Marlin/src/HAL/AVR/eeprom.cpp

@@ -23,7 +23,7 @@
 
 #include "../../inc/MarlinConfig.h"
 
-#if EITHER(EEPROM_SETTINGS, SD_FIRMWARE_UPDATE)
+#if ANY(EEPROM_SETTINGS, SD_FIRMWARE_UPDATE)
 
 /**
  * PersistentStore for Arduino-style EEPROM interface

Marlin/src/HAL/AVR/inc/SanityCheck.h

@@ -95,11 +95,11 @@
 /**
  * The Trinamic library includes SoftwareSerial.h, leading to a compile error.
  */
-#if BOTH(HAS_TRINAMIC_CONFIG, ENDSTOP_INTERRUPTS_FEATURE)
+#if ALL(HAS_TRINAMIC_CONFIG, ENDSTOP_INTERRUPTS_FEATURE)
   #error "TMCStepper includes SoftwareSerial.h which is incompatible with ENDSTOP_INTERRUPTS_FEATURE. Disable ENDSTOP_INTERRUPTS_FEATURE to continue."
 #endif
 
-#if BOTH(HAS_TMC_SW_SERIAL, MONITOR_DRIVER_STATUS)
+#if ALL(HAS_TMC_SW_SERIAL, MONITOR_DRIVER_STATUS)
   #error "MONITOR_DRIVER_STATUS causes performance issues when used with SoftwareSerial-connected drivers. Disable MONITOR_DRIVER_STATUS or use hardware serial to continue."
 #endif
 

Marlin/src/HAL/DUE/HAL_SPI.cpp

@@ -42,7 +42,7 @@
 // Public functions
 // ------------------------
 
-#if EITHER(DUE_SOFTWARE_SPI, FORCE_SOFT_SPI)
+#if ANY(DUE_SOFTWARE_SPI, FORCE_SOFT_SPI)
 
   // ------------------------
   // Software SPI

Marlin/src/HAL/DUE/inc/Conditionals_post.h

@@ -23,6 +23,6 @@
 
 #if USE_FALLBACK_EEPROM
   #define FLASH_EEPROM_EMULATION
-#elif EITHER(I2C_EEPROM, SPI_EEPROM)
+#elif ANY(I2C_EEPROM, SPI_EEPROM)
   #define USE_SHARED_EEPROM 1
 #endif

Marlin/src/HAL/ESP32/HAL.cpp

@@ -165,7 +165,7 @@ void MarlinHAL::init_board() {
 }
 
 void MarlinHAL::idletask() {
-  #if BOTH(WIFISUPPORT, OTASUPPORT)
+  #if ALL(WIFISUPPORT, OTASUPPORT)
     OTA_handle();
   #endif
   TERN_(ESP3D_WIFISUPPORT, esp3dlib.idletask());

Marlin/src/HAL/ESP32/inc/SanityCheck.h

@@ -40,7 +40,7 @@
   #error "TMC220x Software Serial is not supported on ESP32."
 #endif
 
-#if BOTH(WIFISUPPORT, ESP3D_WIFISUPPORT)
+#if ALL(WIFISUPPORT, ESP3D_WIFISUPPORT)
   #error "Only enable one WiFi option, either WIFISUPPORT or ESP3D_WIFISUPPORT."
 #endif
 
@@ -52,18 +52,18 @@
   #error "FAST_PWM_FAN is not available on TinyBee."
 #endif
 
-#if BOTH(I2S_STEPPER_STREAM, BABYSTEPPING) && DISABLED(INTEGRATED_BABYSTEPPING)
+#if ALL(I2S_STEPPER_STREAM, BABYSTEPPING) && DISABLED(INTEGRATED_BABYSTEPPING)
   #error "BABYSTEPPING on I2S stream requires INTEGRATED_BABYSTEPPING."
 #endif
 
 #if USING_PULLDOWNS
   #error "PULLDOWN pin mode is not available on ESP32 boards."
 #endif
 
-#if BOTH(I2S_STEPPER_STREAM, LIN_ADVANCE) && DISABLED(EXPERIMENTAL_I2S_LA)
+#if ALL(I2S_STEPPER_STREAM, LIN_ADVANCE) && DISABLED(EXPERIMENTAL_I2S_LA)
   #error "I2S stream is currently incompatible with LIN_ADVANCE."
 #endif
 
-#if BOTH(I2S_STEPPER_STREAM, PRINTCOUNTER) && PRINTCOUNTER_SAVE_INTERVAL > 0 && DISABLED(PRINTCOUNTER_SYNC)
+#if ALL(I2S_STEPPER_STREAM, PRINTCOUNTER) && PRINTCOUNTER_SAVE_INTERVAL > 0 && DISABLED(PRINTCOUNTER_SYNC)
   #error "PRINTCOUNTER_SAVE_INTERVAL may cause issues on ESP32 with an I2S expander. Define PRINTCOUNTER_SYNC in Configuration.h for an imperfect solution."
 #endif

Marlin/src/HAL/ESP32/ota.cpp

@@ -22,7 +22,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if BOTH(WIFISUPPORT, OTASUPPORT)
+#if ALL(WIFISUPPORT, OTASUPPORT)
 
 #include <WiFi.h>
 #include <ESPmDNS.h>

Marlin/src/HAL/ESP32/spiffs.cpp

@@ -23,7 +23,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if BOTH(WIFISUPPORT, WEBSUPPORT)
+#if ALL(WIFISUPPORT, WEBSUPPORT)
 
 #include "../../core/serial.h"
 

Marlin/src/HAL/ESP32/u8g_esp32_spi.cpp

@@ -25,7 +25,7 @@
 
 #include "../../inc/MarlinConfig.h"
 
-#if EITHER(MKS_MINI_12864, FYSETC_MINI_12864_2_1)
+#if ANY(MKS_MINI_12864, FYSETC_MINI_12864_2_1)
 
 #include <U8glib-HAL.h>
 #include "../shared/HAL_SPI.h"
@@ -101,6 +101,6 @@ uint8_t u8g_eps_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_pt
   return 1;
 }
 
-#endif // EITHER(MKS_MINI_12864, FYSETC_MINI_12864_2_1)
+#endif // MKS_MINI_12864 || FYSETC_MINI_12864_2_1
 
 #endif // ARDUINO_ARCH_ESP32

Marlin/src/HAL/ESP32/web.cpp

@@ -23,7 +23,7 @@
 
 #include "../../inc/MarlinConfigPre.h"
 
-#if BOTH(WIFISUPPORT, WEBSUPPORT)
+#if ALL(WIFISUPPORT, WEBSUPPORT)
 
 #include "../../inc/MarlinConfig.h"
 

Marlin/src/HAL/LINUX/spi_pins.h

@@ -24,7 +24,7 @@
 #include "../../core/macros.h"
 #include "../../inc/MarlinConfigPre.h"
 
-#if BOTH(HAS_MARLINUI_U8GLIB, HAS_MEDIA) && (LCD_PINS_D4 == SD_SCK_PIN || LCD_PINS_EN == SD_MOSI_PIN || DOGLCD_SCK == SD_SCK_PIN || DOGLCD_MOSI == SD_MOSI_PIN)
+#if ALL(HAS_MARLINUI_U8GLIB, HAS_MEDIA) && (LCD_PINS_D4 == SD_SCK_PIN || LCD_PINS_EN == SD_MOSI_PIN || DOGLCD_SCK == SD_SCK_PIN || DOGLCD_MOSI == SD_MOSI_PIN)
   #define SOFTWARE_SPI  // If the SD card and LCD adapter share the same SPI pins, then software SPI is currently
                         // needed due to the speed and mode required for communicating with each device being different.
                         // This requirement can be removed if the SPI access to these devices is updated to use

Marlin/src/HAL/LPC1768/inc/Conditionals_post.h

@@ -23,7 +23,7 @@
 
 #if USE_FALLBACK_EEPROM
   #define FLASH_EEPROM_EMULATION
-#elif EITHER(I2C_EEPROM, SPI_EEPROM)
+#elif ANY(I2C_EEPROM, SPI_EEPROM)
   #define USE_SHARED_EEPROM 1
 #endif
 

Marlin/src/HAL/LPC1768/spi_pins.h

@@ -23,7 +23,7 @@
 
 #include "../../core/macros.h"
 
-#if BOTH(HAS_MEDIA, HAS_MARLINUI_U8GLIB) && (LCD_PINS_D4 == SD_SCK_PIN || LCD_PINS_EN == SD_MOSI_PIN || DOGLCD_SCK == SD_SCK_PIN || DOGLCD_MOSI == SD_MOSI_PIN)
+#if ALL(HAS_MEDIA, HAS_MARLINUI_U8GLIB) && (LCD_PINS_D4 == SD_SCK_PIN || LCD_PINS_EN == SD_MOSI_PIN || DOGLCD_SCK == SD_SCK_PIN || DOGLCD_MOSI == SD_MOSI_PIN)
   #define SOFTWARE_SPI  // If the SD card and LCD adapter share the same SPI pins, then software SPI is currently
                         // needed due to the speed and mode required for communicating with each device being different.
                         // This requirement can be removed if the SPI access to these devices is updated to use