📝 Configurations 02010100 with all kinematics

Marlin/Configuration.h

@@ -35,7 +35,7 @@
  *
  * Advanced settings can be found in Configuration_adv.h
  */
-#define CONFIGURATION_H_VERSION 02010000
+#define CONFIGURATION_H_VERSION 02010100
 
 //===========================================================================
 //============================= Getting Started =============================
@@ -57,15 +57,6 @@
  *                      https://www.thingiverse.com/thing:1278865
  */
 
-//===========================================================================
-//========================== DELTA / SCARA / TPARA ==========================
-//===========================================================================
-//
-// Download configurations from the link above and customize for your machine.
-// Examples are located in config/examples/delta, .../SCARA, and .../TPARA.
-//
-//===========================================================================
-
 // @section info
 
 // Author info of this build printed to the host during boot and M115
@@ -865,7 +856,135 @@
   #define POLAR_SEGMENTS_PER_SECOND 5
 #endif
 
-// Enable for an articulated robot (robot arm). Joints are directly mapped to axes (no kinematics).
+// Enable for DELTA kinematics and configure below
+//#define DELTA
+#if ENABLED(DELTA)
+
+  // Make delta curves from many straight lines (linear interpolation).
+  // This is a trade-off between visible corners (not enough segments)
+  // and processor overload (too many expensive sqrt calls).
+  #define DELTA_SEGMENTS_PER_SECOND 200
+
+  // After homing move down to a height where XY movement is unconstrained
+  //#define DELTA_HOME_TO_SAFE_ZONE
+
+  // Delta calibration menu
+  // uncomment to add three points calibration menu option.
+  // See http://minow.blogspot.com/index.html#4918805519571907051
+  //#define DELTA_CALIBRATION_MENU
+
+  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  //#define DELTA_AUTO_CALIBRATION
+
+  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
+  #if ENABLED(DELTA_AUTO_CALIBRATION)
+    // set the default number of probe points : n*n (1 -> 7)
+    #define DELTA_CALIBRATION_DEFAULT_POINTS 4
+  #endif
+
+  #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
+    // Set the steprate for papertest probing
+    #define PROBE_MANUALLY_STEP 0.05      // (mm)
+  #endif
+
+  // Print surface diameter/2 minus unreachable space (avoid collisions with vertical towers).
+  #define DELTA_PRINTABLE_RADIUS 140.0    // (mm)
+
+  // Maximum reachable area
+  #define DELTA_MAX_RADIUS       140.0    // (mm)
+
+  // Center-to-center distance of the holes in the diagonal push rods.
+  #define DELTA_DIAGONAL_ROD 250.0        // (mm)
+
+  // Distance between bed and nozzle Z home position
+  #define DELTA_HEIGHT 250.00             // (mm) Get this value from G33 auto calibrate
+
+  #define DELTA_ENDSTOP_ADJ { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Horizontal distance bridged by diagonal push rods when effector is centered.
+  #define DELTA_RADIUS 124.0              // (mm) Get this value from G33 auto calibrate
+
+  // Trim adjustments for individual towers
+  // tower angle corrections for X and Y tower / rotate XYZ so Z tower angle = 0
+  // measured in degrees anticlockwise looking from above the printer
+  #define DELTA_TOWER_ANGLE_TRIM { 0.0, 0.0, 0.0 } // Get these values from G33 auto calibrate
+
+  // Delta radius and diagonal rod adjustments (mm)
+  //#define DELTA_RADIUS_TRIM_TOWER { 0.0, 0.0, 0.0 }
+  //#define DELTA_DIAGONAL_ROD_TRIM_TOWER { 0.0, 0.0, 0.0 }
+#endif
+
+/**
+ * MORGAN_SCARA was developed by QHARLEY in South Africa in 2012-2013.
+ * Implemented and slightly reworked by JCERNY in June, 2014.
+ *
+ * Mostly Printed SCARA is an open source design by Tyler Williams. See:
+ *   https://www.thingiverse.com/thing:2487048
+ *   https://www.thingiverse.com/thing:1241491
+ */
+//#define MORGAN_SCARA
+//#define MP_SCARA
+#if EITHER(MORGAN_SCARA, MP_SCARA)
+  // If movement is choppy try lowering this value
+  #define SCARA_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define SCARA_LINKAGE_1 150       // (mm)
+  #define SCARA_LINKAGE_2 150       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define SCARA_OFFSET_X  100       // (mm)
+  #define SCARA_OFFSET_Y  -56       // (mm)
+
+  #if ENABLED(MORGAN_SCARA)
+
+    //#define DEBUG_SCARA_KINEMATICS
+    #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+    // Radius around the center where the arm cannot reach
+    #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+    #define THETA_HOMING_OFFSET  0  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+    #define PSI_HOMING_OFFSET    0  // Calculated from Calibration Guide and M364 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+
+  #elif ENABLED(MP_SCARA)
+
+    #define SCARA_OFFSET_THETA1  12 // degrees
+    #define SCARA_OFFSET_THETA2 131 // degrees
+
+  #endif
+
+#endif
+
+// Enable for TPARA kinematics and configure below
+//#define AXEL_TPARA
+#if ENABLED(AXEL_TPARA)
+  #define DEBUG_ROBOT_KINEMATICS
+  #define ROBOT_SEGMENTS_PER_SECOND 200
+
+  // Length of inner and outer support arms. Measure arm lengths precisely.
+  #define ROBOT_LINKAGE_1 120       // (mm)
+  #define ROBOT_LINKAGE_2 120       // (mm)
+
+  // SCARA tower offset (position of Tower relative to bed zero position)
+  // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
+  #define ROBOT_OFFSET_X    0       // (mm)
+  #define ROBOT_OFFSET_Y    0       // (mm)
+  #define ROBOT_OFFSET_Z    0       // (mm)
+
+  #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
+
+  // Radius around the center where the arm cannot reach
+  #define MIDDLE_DEAD_ZONE_R   0  // (mm)
+
+  // Calculated from Calibration Guide and M360 / M114. See http://reprap.harleystudio.co.za/?page_id=1073
+  #define THETA_HOMING_OFFSET  0
+  #define PSI_HOMING_OFFSET    0
+#endif
+
+// Articulated robot (arm). Joints are directly mapped to axes with no kinematics.
 //#define ARTICULATED_ROBOT_ARM
 
 // For a hot wire cutter with parallel horizontal axes (X, I) where the heights of the two wire
@@ -1239,9 +1358,37 @@
  */
 //#define SENSORLESS_PROBING
 
-//
-// For Z_PROBE_ALLEN_KEY see the Delta example configurations.
-//
+/**
+ * Allen key retractable z-probe as seen on many Kossel delta printers - https://reprap.org/wiki/Kossel#Automatic_bed_leveling_probe
+ * Deploys by touching z-axis belt. Retracts by pushing the probe down.
+ */
+//#define Z_PROBE_ALLEN_KEY
+#if ENABLED(Z_PROBE_ALLEN_KEY)
+  // 2 or 3 sets of coordinates for deploying and retracting the spring loaded touch probe on G29,
+  // if servo actuated touch probe is not defined. Uncomment as appropriate for your printer/probe.
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1 { 30.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2 { 0.0, DELTA_PRINTABLE_RADIUS, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3 { 0.0, (DELTA_PRINTABLE_RADIUS) * 0.75, 100.0 }
+  #define Z_PROBE_ALLEN_KEY_DEPLOY_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_1 { -64.0, 56.0, 23.0 } // Move the probe into position
+  #define Z_PROBE_ALLEN_KEY_STOW_1_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_2 { -64.0, 56.0, 3.0 } // Push it down
+  #define Z_PROBE_ALLEN_KEY_STOW_2_FEEDRATE (XY_PROBE_FEEDRATE)/10
+
+  #define Z_PROBE_ALLEN_KEY_STOW_3 { -64.0, 56.0, 50.0 } // Move it up to clear
+  #define Z_PROBE_ALLEN_KEY_STOW_3_FEEDRATE XY_PROBE_FEEDRATE
+
+  #define Z_PROBE_ALLEN_KEY_STOW_4 { 0.0, 0.0, 50.0 }
+  #define Z_PROBE_ALLEN_KEY_STOW_4_FEEDRATE XY_PROBE_FEEDRATE
+
+#endif // Z_PROBE_ALLEN_KEY
 
 /**
  * Nozzle-to-Probe offsets { X, Y, Z }
@@ -1816,7 +1963,7 @@
 //#define LCD_BED_TRAMMING
 
 #if ENABLED(LCD_BED_TRAMMING)
-  #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 }  // (mm) Left, Front, Right, Back insets
+  #define BED_TRAMMING_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
   #define BED_TRAMMING_HEIGHT      0.0        // (mm) Z height of nozzle at leveling points
   #define BED_TRAMMING_Z_HOP       4.0        // (mm) Z height of nozzle between leveling points
   //#define BED_TRAMMING_INCLUDE_CENTER       // Move to the center after the last corner

Marlin/Configuration_adv.h

@@ -30,7 +30,7 @@
  *
  * Basic settings can be found in Configuration.h
  */
-#define CONFIGURATION_ADV_H_VERSION 02010000
+#define CONFIGURATION_ADV_H_VERSION 02010100
 
 //===========================================================================
 //============================= Thermal Settings ============================

Marlin/src/inc/Version.h

@@ -52,7 +52,7 @@
  * to alert users to major changes.
  */
 
-#define MARLIN_HEX_VERSION 02010000
+#define MARLIN_HEX_VERSION 02010100
 #ifndef REQUIRED_CONFIGURATION_H_VERSION
   #define REQUIRED_CONFIGURATION_H_VERSION MARLIN_HEX_VERSION
 #endif

buildroot/share/git/mfconfig

@@ -110,53 +110,15 @@ if [[ $ACTION == "init" ]]; then
   ((COMMIT_STEPS)) && git add . >/dev/null && git commit -m "Commit for comparison" >/dev/null
 
   # Init Cartesian/SCARA/TPARA configurations to default
-  echo "- Initializing Cartesian/SCARA/TPARA configs to default state..."
+  echo "- Initializing configs to default state..."
 
-  find "$CEXA" -name $BC ! -path */delta/* -print0 \
+  find "$CEXA" -name $BC -print0 \
     | while read -d $'\0' F ; do cp "$CDEF/$BC" "$F" ; done
-  find "$CEXA" -name $AC ! -path */delta/* -print0 \
+  find "$CEXA" -name $AC -print0 \
     | while read -d $'\0' F ; do cp "$CDEF/$AC" "$F" ; done
 
   # DEBUG: Commit the reset for review
-  ((COMMIT_STEPS)) && git add . >/dev/null && git commit -m "Reset Cartesian/SCARA/TPARA configs..." >/dev/null
-
-  # Create base Delta configurations
-  cp "$CDEF"/* "$CEXA/delta/generic"
-
-  # DEBUG: Commit the reset for review
-  ((COMMIT_STEPS)) && git add . >/dev/null && git commit -m "Reset Generic Delta..." >/dev/null
-
-  cp -R "$TEMP/$CEXA/delta/generic"/Conf* "$CEXA/delta/generic"
-
-  # DEBUG: Commit Generic Delta changes for review
-  ((COMMIT_STEPS)) && git add . >/dev/null && git commit -m "Apply Generic Delta..." >/dev/null
-
-  # Reset all Delta configs to the generic version
-  find "$CEXA/delta" -name $BC ! -path */generic/* -print0 \
-    | while read -d $'\0' F ; do cp "$CEXA/delta/generic/$BC" "$F" ; done
-  find "$CEXA/delta" -name $AC ! -path */generic/* -print0 \
-    | while read -d $'\0' F ; do cp "$CEXA/delta/generic/$AC" "$F" ; done
-
-  # DEBUG: Commit the Delta reset for review
-  ((COMMIT_STEPS)) && git add . >/dev/null && git commit -m "Reset Delta configs..." >/dev/null
-
-  # Reset all SCARA configs to the default cartesian
-  find "$CEXA/SCARA" -name $BC \
-    | while read -d $'\0' F ; do cp "$CDEF/$BC" "$F" ; done
-  find "$CEXA/SCARA" -name $AC \
-    | while read -d $'\0' F ; do cp "$CDEF/$AC" "$F" ; done
-
-  # DEBUG: Commit the SCARA reset for review
-  ((COMMIT_STEPS)) && git add . >/dev/null && git commit -m "Reset SCARA..." >/dev/null
-
-  # Reset all TPARA configs to the default cartesian
-  find "$CEXA/TPARA" -name $BC \
-    | while read -d $'\0' F ; do cp "$CDEF/$BC" "$F" ; done
-  find "$CEXA/TPARA" -name $AC \
-    | while read -d $'\0' F ; do cp "$CDEF/$AC" "$F" ; done
-
-  # DEBUG: Commit the TPARA reset for review
-  ((COMMIT_STEPS)) && git add . >/dev/null && git commit -m "Reset TPARA..." >/dev/null
+  ((COMMIT_STEPS)) && git add . >/dev/null && git commit -m "Reset configs..." >/dev/null
 
   # Update the %VERSION% in the README.md file
   VERS=$( echo $EXPORT | $SED 's/release-//' )