Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

Sign up for GitHub

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

Clarify TMC2209 Sensitivity vs. Others #15092

Merged
merged 2 commits into from
Aug 29, 2019
Merged

Clarify TMC2209 Sensitivity vs. Others #15092

Show file tree
Hide file tree
Changes from all commits
Commits
Show all changes
2 commits
Select commit Hold shift + click to select a range
e49256f
Initial commit
thisiskeithb Aug 29, 2019
6f4a4e3
Tweak SENSORLESS_HOMING description
thinkyhead Aug 29, 2019
File filter

Filter by extension

Filter by extension
Conversations
Failed to load comments.
Loading
Jump to
Jump to file
Failed to load files.
Loading
Diff view
Diff view
10 changes: 6 additions & 4 deletions Marlin/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/default/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/3DFabXYZ/Migbot/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/ADIMLab/Gantry v1/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1926,10 +1926,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/ADIMLab/Gantry v2/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/AlephObjects/TAZ4/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/Alfawise/U20/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1943,10 +1943,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/AliExpress/UM2pExt/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1942,10 +1942,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/Anet/A2/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/Anet/A2plus/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/Anet/A6/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/Anet/A8/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/Anet/A8plus/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/Anet/E16/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/AnyCubic/i3/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/ArmEd/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1944,10 +1944,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/BIBO/TouchX/cyclops/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/BIBO/TouchX/default/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/BQ/Hephestos/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/BQ/Hephestos_2/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1948,10 +1948,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/BQ/WITBOX/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/Cartesio/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
10 changes: 6 additions & 4 deletions config/examples/Creality/CR-10/Configuration_adv.h
View file
Open in desktop
Original file line number Diff line number Diff line change
Expand Up @@ -1940,10 +1940,12 @@
* Connect the stepper driver's DIAG1 pin to the X/Y endstop pin.
* X, Y, and Z homing will always be done in spreadCycle mode.
*
* X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity.
* Use M914 X Y Z to live-adjust the sensitivity.
* Higher: LESS sensitive. (Too high => failure to trigger)
* Lower: MORE sensitive. (Too low => false positives)
* X/Y/Z_STALL_SENSITIVITY is the default stall threshold.
* Use M914 X Y Z to set the stall threshold at runtime:
*
* Sensitivity TMC2209 Others
* HIGHEST 255 -64 (Too sensitive => False positive)
* LOWEST 0 63 (Too insensitive => No trigger)
*
* It is recommended to set [XYZ]_HOME_BUMP_MM to 0.
*
Expand Down
Loading