[BUG] Ender 5 Plus `bugfix-2.0.x` code compiles with errors in VS Code #21576

TheAZtech · 2021-04-09T19:23:20Z

Did you test the latest `bugfix-2.0.x` code?

Yes, and the problem still exists.

Bug Description

I am attempting to compile the bugfix-2.0.x code using the Ender 5 Plus configuration files and it dumps several errors in the process in VS Code. I was able to successfully compile the bugfix-2.0.x code with the stock configuration files, but when adding the Ender 5 Plus files, it fails. The following screen shots are the locations of the code that is throwing the errors.

Bug Timeline

Unknown.

Expected behavior

I expected a successful compilation. :-)

Actual behavior

The compilation failed.

Steps to Reproduce

Open the folder where bugfix-2.0.x code is stored; replace the configuration files from the 'Configurations-bugfix-2.0.x' file for the 'Ender-5 Plus'. Open folder in VS Code and click the hammer... Failed.

Version of Marlin Firmware

Marlin bugfix-2.0.x code

Printer model

Ender 5 Plus

Electronics

Creality Silent Board V2.2

Add-ons

No

Your Slicer

Cura

Host Software

OctoPrint

The text was updated successfully, but these errors were encountered:

Vertabreak · 2021-04-09T19:43:22Z

The problems tab in vscode should be ignored by end users show us the terminal tab the real errors are in red and prevent compile.

i pulled latest and can confirm.

descipher · 2021-04-09T21:20:50Z

is SDSUPPORT defined?

#if ENABLED(SDSUPPORT)
int16_t DGUSScreenHandler::top_file = 0,
DGUSScreenHandler::file_to_print = 0;
static ExtUI::FileList filelist;
#endif

Vertabreak · 2021-04-09T21:27:47Z

i used the provided example direct from GitHub and it was enabled.
https://github.com/MarlinFirmware/Configurations/tree/bugfix-2.0.x/config/examples/Creality/Ender-5%20Plus

descipher · 2021-04-09T21:34:22Z

I have not synced for 24 hours but that's what it should have. I'll resync now to be sure.

Vertabreak · 2021-04-09T21:37:28Z

here is a copy i'm working with just pulled bugfix and matching config for the ender 5 +
Marlin-bugfix-2.0.x-ender5+.zip

descipher · 2021-04-09T22:43:39Z

https://github.com/MarlinFirmware/Marlin/pull/21485/files
Looks like its here, can't verify right now...

TheAZtech · 2021-04-10T05:47:07Z

@Vertabreak, Thank you for that, Now I know what to include when I submit an issue. Y'all are rockstars and I will be paying attention to this post for further information. let me know if anyone needs anything else.

descipher · 2021-04-11T16:14:28Z

Definitely broken shortly after #21485 issues start showing up on #21500 for AVR boards.
This impacts:
DGUS_LCD_UI_ORIGIN, DGUS_LCD_UI_FYSETC, DGUS_LCD_UI_HIPRECY and DGUS_LCD_UI_MKS still has other issues compiling at the moment.
see:
Marlin\src\lcd\extui\lib\dgus\mks\DGUSScreenHandler.cpp: In static member function 'static void GcodeSuite::M1002()':
Marlin\src\lcd\extui\lib\dgus\mks\DGUSScreenHandler.cpp:1274:22: error: no matching function for call to 'GcodeSuite::set_e_relative(bool)'
set_e_relative(true); // M83
^

D337z · 2021-04-18T04:56:02Z

And here's something that seems to be related, but I'm not sure.
Might looks at changing over to U8G2

`Arduino: 1.8.13 (Windows 10), Board: "Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)"

In file included from sketch\src\lcd\dogm/marlinui_DOGM.h:31:0,

             from sketch\src\lcd\marlinui.cpp:141:

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:37:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:40:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:53:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:56:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_hw_spi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_RRD::init(pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:71:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_rrd_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset);   // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_SH1106_128X64_2X_I2C_2_WIRE::init(uint8_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:81:59: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_sh1106_128x64_2x_i2c_2_wire, options); }

                                                       ^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1306_128X64_2X_I2C_2_WIRE::init(uint8_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:90:59: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_ssd1306_128x64_2x_i2c_2_wire, options); }

                                                       ^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_TFT_320X240_UPSCALE_FROM_128X64::init(uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:103:77: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t cs, uint8_t rs, uint8_t reset = U8G_PIN_NONE) { U8GLIB::init(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset); }

                                                                         ^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:115:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset);

         ^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:118:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset);

         ^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:131:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_ssd1309_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm/HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm/HAL_LCD_class_defines.h:134:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_ssd1309_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

In file included from sketch\src\lcd\dogm\marlinui_DOGM.h:31:0,

             from sketch\src\lcd\dogm\lcdprint_u8g.cpp:14:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:37:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:40:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:53:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:56:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_hw_spi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_RRD::init(pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:71:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_rrd_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset);   // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SH1106_128X64_2X_I2C_2_WIRE::init(uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:81:59: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_sh1106_128x64_2x_i2c_2_wire, options); }

                                                       ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1306_128X64_2X_I2C_2_WIRE::init(uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:90:59: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_ssd1306_128x64_2x_i2c_2_wire, options); }

                                                       ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_TFT_320X240_UPSCALE_FROM_128X64::init(uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:103:77: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t cs, uint8_t rs, uint8_t reset = U8G_PIN_NONE) { U8GLIB::init(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset); }

                                                                         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:115:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:118:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:131:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_ssd1309_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:134:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_ssd1309_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

In file included from sketch\src\lcd\dogm\marlinui_DOGM.h:31:0,

             from sketch\src\lcd\dogm\dogm_Statusscreen.h:32,

             from sketch\src\lcd\dogm\status_screen_DOGM.cpp:32:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:37:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:40:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:53:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:56:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_hw_spi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_RRD::init(pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:71:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_rrd_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset);   // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SH1106_128X64_2X_I2C_2_WIRE::init(uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:81:59: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_sh1106_128x64_2x_i2c_2_wire, options); }

                                                       ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1306_128X64_2X_I2C_2_WIRE::init(uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:90:59: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_ssd1306_128x64_2x_i2c_2_wire, options); }

                                                       ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_TFT_320X240_UPSCALE_FROM_128X64::init(uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:103:77: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t cs, uint8_t rs, uint8_t reset = U8G_PIN_NONE) { U8GLIB::init(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset); }

                                                                         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:115:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:118:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:131:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_ssd1309_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:134:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_ssd1309_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

In file included from sketch\src\lcd\dogm\marlinui_DOGM.h:31:0,

             from sketch\src\lcd\dogm\marlinui_DOGM.cpp:42:

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:37:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_64128N_2X_HAL::init(pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:40:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7565_64128n_HAL_2x_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:53:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_4X_HAL::init(pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:56:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_HAL_4x_hw_spi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset); // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_ST7920_128X64_RRD::init(pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:71:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_st7920_128x64_rrd_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, U8G_PIN_NONE, (uint8_t)reset);   // a0 = U8G_PIN_NONE

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SH1106_128X64_2X_I2C_2_WIRE::init(uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:81:59: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_sh1106_128x64_2x_i2c_2_wire, options); }

                                                       ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1306_128X64_2X_I2C_2_WIRE::init(uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:90:59: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t options = U8G_I2C_OPT_NONE) { U8GLIB::init(&u8g_dev_ssd1306_128x64_2x_i2c_2_wire, options); }

                                                       ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_TFT_320X240_UPSCALE_FROM_128X64::init(uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:103:77: error: 'init' is not a member of 'U8GLIB'

void init(uint8_t cs, uint8_t rs, uint8_t reset = U8G_PIN_NONE) { U8GLIB::init(&u8g_dev_tft_320x240_upscale_from_128x64, cs, rs, reset); }

                                                                         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:115:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_sw_spi, sck, mosi, cs, a0, reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_MINI12864_2X_HAL::init(uint8_t, uint8_t, uint8_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:118:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_uc1701_mini12864_HAL_2x_hw_spi, cs, a0, reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:131:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_ssd1309_sw_spi, (uint8_t)sck, (uint8_t)mosi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

sketch\src\lcd\dogm\HAL_LCD_class_defines.h: In member function 'void U8GLIB_SSD1309_128X64_HAL::init(pin_t, pin_t, pin_t)':

sketch\src\lcd\dogm\HAL_LCD_class_defines.h:134:13: error: 'init' is not a member of 'U8GLIB'

 U8GLIB::init(&u8g_dev_ssd1309_hw_spi, (uint8_t)cs, (uint8_t)a0, (uint8_t)reset);

         ^~~~

exit status 1

Error compiling for board Arduino Mega or Mega 2560.

This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
`

ellensp · 2021-05-16T09:32:10Z

@D337z you cannot use the U8G lib that arduino uses, you have to to the marlin fork of U8G https://github.com/MarlinFirmware/U8glib-HAL
Easiest way to do that is to use platformio, then it automatically uses the correct library.
This is also unrelated as the Ender 5 Plus does not use that type of LCD

ellensp · 2021-05-16T10:28:20Z

Can Someone try this diff on current bugfix, it compiles, but I don't have the lcd.
Check what happens whey your printing from sd and pause printing from lcd

diff --git a/Marlin/src/lcd/extui/dgus/origin/DGUSDisplayDef.cpp b/Marlin/src/lcd/extui/dgus/origin/DGUSDisplayDef.cpp
index 1c2944bb4f..31bcaac236 100644
--- a/Marlin/src/lcd/extui/dgus/origin/DGUSDisplayDef.cpp
+++ b/Marlin/src/lcd/extui/dgus/origin/DGUSDisplayDef.cpp
@@ -194,9 +194,8 @@ const struct DGUS_VP_Variable ListOfVP[] PROGMEM = {

   // Temperature Data
   #if HOTENDS >= 1
-    VPHELPER(VP_T_E0_Is, nullptr, nullptr, SET_VARIABLE(getActualTemp_celsius, E0, long)),
-    VPHELPER(VP_T_E0_Set, nullptr, GET_VARIABLE(setTargetTemp_celsius, E0),
-                                   SET_VARIABLE(getTargetTemp_celsius, E0)),
+    VPHELPER(VP_T_E0_Is, &thermalManager.temp_hotend[0].celsius, nullptr, ScreenHandler.DGUSLCD_SendFloatAsLongValueToDisplay<0>),
+    VPHELPER(VP_T_E0_Set, &thermalManager.temp_hotend[0].target, ScreenHandler.HandleTemperatureChanged, &ScreenHandler.DGUSLCD_SendWordValueToDisplay),
     VPHELPER(VP_Flowrate_E0, nullptr, ScreenHandler.HandleFlowRateChanged, &ScreenHandler.DGUSLCD_SendWordValueToDisplay),
     VPHELPER(VP_EPos, &destination.e, nullptr, ScreenHandler.DGUSLCD_SendFloatAsLongValueToDisplay<2>),
     VPHELPER(VP_MOVE_E0, nullptr, &ScreenHandler.HandleManualExtrude, nullptr),
diff --git a/Marlin/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp b/Marlin/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp
index f05dfc6f70..fe7c4120b8 100644
--- a/Marlin/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp
+++ b/Marlin/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp
@@ -85,7 +85,7 @@

       case 1: // Pause

-        GotoScreen(MKSLCD_SCREEN_PAUSE);
+        GotoScreen(DGUSLCD_SCREEN_POPUP);
         if (!ExtUI::isPrintingFromMediaPaused()) {
           ExtUI::pausePrint();
           //ExtUI::mks_pausePrint();

nicwilson58 · 2021-05-19T01:31:59Z

VPHELPER(VP_T_E0_Is, &thermalManager.temp_hotend[0].celsius, nullptr, ScreenHandler.DGUSLCD_SendFloatAsLongValueToDisplay<0>),
+    VPHELPER(VP_T_E0_Set, &thermalManager.temp_hotend[0].target, ScreenHandler.HandleTemperatureChanged, &ScreenHandler.DGUSLCD_SendWordValueToDisplay),

I compiled this for the CR10s Pro V2 which had the same compile errors as the Ender5+ had using this DGUS version, and with your changes above it compiles and works for the LCD, however when setting the temperatures, the nozzle shows correct, but bed heats but shows random temperature values on the LCD, which given the changes shown looks like a possible issue with the changes.

ellensp · 2021-05-19T11:23:20Z

@nicwilson58 I don't understand your comment. The edits where for setting E0 temp, nothing to do with the bed...

Only thing I can see is perhaps the float is causing issues...
E1 and the bed both use DGUSLCD_SendWordValueToDisplay
where as E0 used DGUSLCD_SendFloatAsLongValueToDisplay
Also spotted an issue with HOTENDS >= 2 and corrected this.

Try this version

--- a/Marlin/src/lcd/extui/dgus/origin/DGUSDisplayDef.cpp
+++ b/Marlin/src/lcd/extui/dgus/origin/DGUSDisplayDef.cpp
@@ -194,9 +194,8 @@ const struct DGUS_VP_Variable ListOfVP[] PROGMEM = {
 
   // Temperature Data
   #if HOTENDS >= 1
-    VPHELPER(VP_T_E0_Is, nullptr, nullptr, SET_VARIABLE(getActualTemp_celsius, E0, long)),
-    VPHELPER(VP_T_E0_Set, nullptr, GET_VARIABLE(setTargetTemp_celsius, E0),
-                                   SET_VARIABLE(getTargetTemp_celsius, E0)),
+    VPHELPER(VP_T_E0_Is, &thermalManager.temp_hotend[0].celsius, nullptr, ScreenHandler.DGUSLCD_SendWordValueToDisplay),
+    VPHELPER(VP_T_E0_Set, &thermalManager.temp_hotend[0].target, ScreenHandler.HandleTemperatureChanged, &ScreenHandler.DGUSLCD_SendWordValueToDisplay),
     VPHELPER(VP_Flowrate_E0, nullptr, ScreenHandler.HandleFlowRateChanged, &ScreenHandler.DGUSLCD_SendWordValueToDisplay),
     VPHELPER(VP_EPos, &destination.e, nullptr, ScreenHandler.DGUSLCD_SendFloatAsLongValueToDisplay<2>),
     VPHELPER(VP_MOVE_E0, nullptr, &ScreenHandler.HandleManualExtrude, nullptr),
@@ -216,7 +215,7 @@ const struct DGUS_VP_Variable ListOfVP[] PROGMEM = {
     #endif
   #endif
   #if HOTENDS >= 2
-    VPHELPER(VP_T_E1_Is, &thermalManager.temp_hotend[1].celsius, nullptr, DGUSLCD_SendWordValueToDisplay),
+    VPHELPER(VP_T_E1_Is, &thermalManager.temp_hotend[1].celsius, nullptr, ScreenHandler.DGUSLCD_SendWordValueToDisplay),
diff --git a/Marlin/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp b/Marlin/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp
index f05dfc6f70..fe7c4120b8 100644
--- a/Marlin/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp
+++ b/Marlin/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp
@@ -85,7 +85,7 @@

       case 1: // Pause

-        GotoScreen(MKSLCD_SCREEN_PAUSE);
+        GotoScreen(DGUSLCD_SCREEN_POPUP);
         if (!ExtUI::isPrintingFromMediaPaused()) {
           ExtUI::pausePrint();
           //ExtUI::mks_pausePrint();

borjarodi · 2021-05-19T20:50:45Z

Thanks to the comments, I have managed to compile the code, but with a warning, which I have attached in an image. Now the problem is that when I turn on the Ender 5 Plus the screen is frozen. Any solution? Thank you very much for your help.

nicwilson58 · 2021-05-21T00:06:00Z

@nicwilson58 I don't understand your comment. The edits where for setting E0 temp, nothing to do with the bed...

I see that now, I think the confusion for me came from the way Marlin has always been that I have seen, if you go to PID tuning for the hotend its always been shown as E1 not E0

ellensp · 2021-05-21T02:11:57Z

yes boards are e0, e1 etc and on LCD are E1, E2 etc, this has always irked me also...

nicwilson58 · 2021-05-21T02:56:18Z

yes boards are e0, e1 etc and on LCD are E1, E2 etc, this has always irked me also...

Thanks, the changes seem to work, next to find out why the tools menu does nothing.

D337z · 2021-05-21T04:18:42Z

The bed, if set is E-1. And I don't have a standard Ender 5 Plus. It's heavily modified.

…

On Thu, May 20, 2021, 21:56 nicwilson58 ***@***.***> wrote: yes boards are e0, e1 etc and on LCD are E1, E2 etc, this has always irked me also... Thanks, the changes seem to work, next to find out why the tools menu does nothing. — You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub <#21576 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ATOTXI6B4KDUESFOD5GTSKTTOXDWDANCNFSM42VRISXQ> .

nicwilson58 · 2021-05-21T04:30:35Z

Thanks to the comments, I have managed to compile the code, but with a warning, which I have attached in an image. Now the problem is that when I turn on the Ender 5 Plus the screen is frozen. Any solution? Thank you very much for your help.

try using the matching screen firmware.

ellensp · 2021-05-22T06:47:43Z

@nicwilson58 the question remains should I turn my patch into a pr, is some functionality better than none at all...

shaders · 2021-06-22T13:11:29Z

VPHELPER(VP_T_E0_Is, &thermalManager.temp_hotend[0].celsius, nullptr, ScreenHandler.DGUSLCD_SendFloatAsLongValueToDisplay<0>),

and
VPHELPER(VP_T_Bed_Is, &thermalManager.temp_bed.celsius, nullptr, ScreenHandler.DGUSLCD_SendFloatAsLongValueToDisplay<0>),

Is actually correct code. Otherwise display shows garbage numbers.

CRCinAU · 2021-07-10T14:32:10Z

Checking the latest bugfix-2.0.x branch for both configs and Marlin code today, and I get the following errors:

Marlin/src/lcd/extui/dgus/origin/DGUSDisplayDef.cpp:277:1: error: no matches converting function 'GetVariable' to type 'void (*)(struct DGUS_VP_Variable&, void*)'
 };
 ^
In file included from Marlin/src/lcd/extui/dgus/origin/DGUSDisplayDef.cpp:32:0:
Marlin/src/lcd/extui/dgus/origin/../DGUSDisplay.h:76:15: note: candidate is: template<class T, void (* Setter)(float, T), T selector> static void DGUSDisplay::GetVariable(DGUS_VP_Variable&, void*)
   static void GetVariable(DGUS_VP_Variable &var, void *val_ptr) {
               ^~~~~~~~~~~
Compiling .pio/build/mega2560/src/src/module/probe.cpp.o
*** [.pio/build/mega2560/src/src/lcd/extui/dgus/origin/DGUSDisplayDef.cpp.o] Error 1
Marlin/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp: In static member function 'static void DGUSScreenHandler::DGUSLCD_SD_ResumePauseAbort(DGUS_VP_Variable&, void*)':
Marlin/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp:88:20: error: 'MKSLCD_SCREEN_PAUSE' was not declared in this scope
         GotoScreen(MKSLCD_SCREEN_PAUSE);
                    ^~~~~~~~~~~~~~~~~~~
Marlin/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp:88:20: note: suggested alternative: 'DGUSLCD_SCREEN_UNUSED'
         GotoScreen(MKSLCD_SCREEN_PAUSE);
                    ^~~~~~~~~~~~~~~~~~~
                    DGUSLCD_SCREEN_UNUSED
*** [.pio/build/mega2560/src/src/lcd/extui/dgus/origin/DGUSScreenHandler.cpp.o] Error 1

I didn't want to start another Issue, as this may well be related - but its reproduced by using both the stock config and todays bugfix-2.0.x checkout.

ellensp · 2021-07-11T02:55:35Z

GetVariable and SetVariable where added in #18718
a proposal that was never actually finished, that got merged anyway... :(
Reverting that part of the code and you get to the last error MKSLCD_SCREEN_PAUSE which is simply not defined for this dispaly.
It should be DGUS_SCREEN_PAUSE, but that is also not defined. I don't know how you would find out what screen number this should be set to... so it sits waiting.

CRCinAU · 2021-07-11T03:26:02Z

It doesn't look like the original PR author has been active since August 2020 - as such, pinging @thinkyhead to see how we should get to the bottom of this...

Hookedon3D · 2021-07-24T21:09:53Z

Any update on this? I am trying to compile for my stock E5+ and I am getting the same error. Thanks in advance!

ellensp · 2021-07-30T11:12:22Z

I have created a PR to get basic functionally back working on Marlin bugfix.

Hookedon3D · 2021-07-30T16:33:30Z

I just redownloaded everything and tried still the same error "Marlin\src\lcd\extui\dgus\origin\DGUSDisplayDef.cpp:277:1: error: no matches converting function 'GetVariable' to type 'void ()(struct DGUS_VP_Variable&, void)'"

ellensp · 2021-07-31T00:58:27Z

@Hookedon3D This was only merged 5 minutes ago, so is only just now been added to bugfix.
A PR is a pull request, code waiting review by the admins before being added (merged) into Marlin.
You need to manually apply PR's to your code to try them, or replicate the code changes you want. Or wait for them to be merged.

Hookedon3D · 2021-07-31T01:01:32Z

Oh ok, looks like it's merged? So, I'll go ahead and redownload it and try it again. Thank you!

github-actions · 2021-09-29T01:42:33Z

This issue has been automatically locked since there has not been any recent activity after it was closed. Please open a new issue for related bugs.

thisiskeithb added the C: LCD & Controllers label Apr 9, 2021

ellensp mentioned this issue Apr 19, 2021

[BUG] Creality Ender 5 Plus configs won't compile on Bugfix #21663

Closed

This was referenced May 9, 2021

Firmware builder error #21851

Closed

[BUG] Ender 5 Plus configuration.h or code problem MarlinFirmware/Configurations#491

Closed

ellensp mentioned this issue May 19, 2021

[BUG] I can´t compile Marlin with LCD error #21948

Closed

ellensp mentioned this issue Jun 23, 2021

configuration Display issue MarlinFirmware/Configurations#527

Closed

ellensp mentioned this issue Jul 1, 2021

[BUG] (bug summary) #22272

Closed

thisiskeithb mentioned this issue Jul 11, 2021

[BUG] Ender 5 Plus - Sample configurations fail to build - DGUS problems #22334

Closed

thisiskeithb added the Bug: Confirmed ! label Jul 11, 2021

thisiskeithb added help wanted Needs: Patch A patch is needed to fix this labels Jul 11, 2021

ellensp mentioned this issue Jul 30, 2021

Fix DGUS displays compile #22464

Merged

ellensp closed this as completed Jul 31, 2021

github-actions bot removed help wanted Needs: Patch A patch is needed to fix this labels Jul 31, 2021

github-actions bot locked and limited conversation to collaborators Sep 29, 2021

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

[BUG] Ender 5 Plus `bugfix-2.0.x` code compiles with errors in VS Code #21576

[BUG] Ender 5 Plus `bugfix-2.0.x` code compiles with errors in VS Code #21576

TheAZtech commented Apr 9, 2021

Vertabreak commented Apr 9, 2021 •

edited

Loading

descipher commented Apr 9, 2021

Vertabreak commented Apr 9, 2021 •

edited

Loading

descipher commented Apr 9, 2021

Vertabreak commented Apr 9, 2021

descipher commented Apr 9, 2021

TheAZtech commented Apr 10, 2021 •

edited

Loading

descipher commented Apr 11, 2021

D337z commented Apr 18, 2021

ellensp commented May 16, 2021

ellensp commented May 16, 2021 •

edited

Loading

nicwilson58 commented May 19, 2021

ellensp commented May 19, 2021 •

edited

Loading

borjarodi commented May 19, 2021 •

edited

Loading

nicwilson58 commented May 21, 2021 •

edited

Loading

ellensp commented May 21, 2021

nicwilson58 commented May 21, 2021

D337z commented May 21, 2021 via email

nicwilson58 commented May 21, 2021 •

edited

Loading

ellensp commented May 22, 2021 •

edited

Loading

shaders commented Jun 22, 2021

CRCinAU commented Jul 10, 2021

ellensp commented Jul 11, 2021

CRCinAU commented Jul 11, 2021

Hookedon3D commented Jul 24, 2021

ellensp commented Jul 30, 2021 •

edited

Loading

Hookedon3D commented Jul 30, 2021

ellensp commented Jul 31, 2021

Hookedon3D commented Jul 31, 2021

github-actions bot commented Sep 29, 2021

[BUG] Ender 5 Plus bugfix-2.0.x code compiles with errors in VS Code #21576

[BUG] Ender 5 Plus bugfix-2.0.x code compiles with errors in VS Code #21576

Comments

TheAZtech commented Apr 9, 2021

Did you test the latest bugfix-2.0.x code?

Bug Description

Bug Timeline

Expected behavior

Actual behavior

Steps to Reproduce

Version of Marlin Firmware

Printer model

Electronics

Add-ons

Your Slicer

Host Software

Vertabreak commented Apr 9, 2021 • edited Loading

descipher commented Apr 9, 2021

Vertabreak commented Apr 9, 2021 • edited Loading

descipher commented Apr 9, 2021

Vertabreak commented Apr 9, 2021

descipher commented Apr 9, 2021

TheAZtech commented Apr 10, 2021 • edited Loading

descipher commented Apr 11, 2021

D337z commented Apr 18, 2021

ellensp commented May 16, 2021

ellensp commented May 16, 2021 • edited Loading

nicwilson58 commented May 19, 2021

ellensp commented May 19, 2021 • edited Loading

borjarodi commented May 19, 2021 • edited Loading

nicwilson58 commented May 21, 2021 • edited Loading

ellensp commented May 21, 2021

nicwilson58 commented May 21, 2021

D337z commented May 21, 2021 via email

nicwilson58 commented May 21, 2021 • edited Loading

ellensp commented May 22, 2021 • edited Loading

shaders commented Jun 22, 2021

CRCinAU commented Jul 10, 2021

ellensp commented Jul 11, 2021

CRCinAU commented Jul 11, 2021

Hookedon3D commented Jul 24, 2021

ellensp commented Jul 30, 2021 • edited Loading

Hookedon3D commented Jul 30, 2021

ellensp commented Jul 31, 2021

Hookedon3D commented Jul 31, 2021

github-actions bot commented Sep 29, 2021

[BUG] Ender 5 Plus `bugfix-2.0.x` code compiles with errors in VS Code #21576

[BUG] Ender 5 Plus `bugfix-2.0.x` code compiles with errors in VS Code #21576

Did you test the latest `bugfix-2.0.x` code?

Vertabreak commented Apr 9, 2021 •

edited

Loading

Vertabreak commented Apr 9, 2021 •

edited

Loading

TheAZtech commented Apr 10, 2021 •

edited

Loading

ellensp commented May 16, 2021 •

edited

Loading

ellensp commented May 19, 2021 •

edited

Loading

borjarodi commented May 19, 2021 •

edited

Loading

nicwilson58 commented May 21, 2021 •

edited

Loading

nicwilson58 commented May 21, 2021 •

edited

Loading

ellensp commented May 22, 2021 •

edited

Loading

ellensp commented Jul 30, 2021 •

edited

Loading