🔧 Assume RAMPS_CREALITY is not CR2020

Marlin/src/pins/ramps/pins_RAMPS_CREALITY.h

@@ -29,50 +29,74 @@
 
 #define BOARD_INFO_NAME "Creality3D RAMPS"
 
+//#define CR2020_INDUSTRIAL_SERIES                // Use layout specific to CR2020
+
+//
+// 4-pin expansion header
+//
+#define EXP1_PIN                              65  // A11 - Used by CR2020 Industrial series for case
+#define EXP2_PIN                              66  // A12
+#define EXP3_PIN                              11  // RAMPS: SERVO0_PIN
+#define EXP4_PIN                              12  // RAMPS: PS_ON_PIN
+
+//
+// Servos
+//
+#define SERVO1_PIN                            12
+
 //
 // Heaters / Fans
 //
 #define MOSFET_B_PIN                           7
 #define FAN0_PIN                               9
 
+//
+// Filament Runout Sensor
+//
 #define FIL_RUNOUT_PIN                         2
 #if NUM_RUNOUT_SENSORS >= 2
   #define FIL_RUNOUT2_PIN                     15  // Creality CR-X can use dual runout sensors
 #endif
 
-#ifndef SD_DETECT_PIN
-  #if SD_CONNECTION_IS(ONBOARD)
-    //#define HAS_ONBOARD_SD_DETECT               // If the SD_DETECT_PIN is wired up
+//
+// Misc. Functions
+//
+#ifdef CR2020_INDUSTRIAL_SERIES
+  #if ENABLED(PSU_CONTROL) && !defined(PS_ON_PIN)
+    #define PS_ON_PIN                         40  // Used by CR2020 Industrial series
   #endif
-  #if ENABLED(HAS_ONBOARD_SD_DETECT) || !SD_CONNECTION_IS(ONBOARD)
-    #define SD_DETECT_PIN                     49
+  #ifndef SUICIDE_PIN
+    #define SUICIDE_PIN                       12  // Used by CR2020 Industrial series
+  #endif
+  #ifndef SUICIDE_PIN_STATE
+    #define SUICIDE_PIN_STATE               HIGH
   #endif
-#endif
-
-#ifndef PS_ON_PIN
-  #define PS_ON_PIN                           40  // Used by CR2020 Industrial series
 #endif
 
 #if ENABLED(CASE_LIGHT_ENABLE) && !defined(CASE_LIGHT_PIN)
   #define CASE_LIGHT_PIN                      65
 #endif
 
-#define SERVO1_PIN                            12
+//
+// SD Card
+//
+#ifndef SD_DETECT_PIN
+  #if SD_CONNECTION_IS(ONBOARD)
+    //#define HAS_ONBOARD_SD_DETECT               // If the SD_DETECT_PIN is wired up
+  #endif
+  #if ENABLED(HAS_ONBOARD_SD_DETECT) || !SD_CONNECTION_IS(ONBOARD)
+    #define SD_DETECT_PIN                     49
+  #endif
+#endif
 
+//
+// Based on RAMPS 1.4
+//
 #include "pins_RAMPS.h"
 
+//
+// LCD / Controller
+//
 #ifndef BEEPER_PIN
   #define BEEPER_PIN                          37  // Always define beeper pin so Play Tone works with ExtUI
 #endif
-
-#define EXP1_PIN                              65  // A11 - Used by CR2020 Industrial series for case
-#define EXP2_PIN                              66  // A12
-#define EXP3_PIN                              11  // SERVO0_PIN
-#define EXP4_PIN                              12  // PS_ON_PIN
-
-#ifndef SUICIDE_PIN
-  #define SUICIDE_PIN                         12  // Used by CR2020 Industrial series
-  #ifndef SUICIDE_PIN_STATE
-    #define SUICIDE_PIN_STATE               HIGH
-  #endif
-#endif