Merge branch 'bugfix-2.1.x' into pr/24786

.gitignore

@@ -147,6 +147,7 @@ vc-fileutils.settings
 imgui.ini
 eeprom.dat
 spi_flash.bin
+fs.img
 
 #cmake
 CMakeLists.txt

Makefile

@@ -27,7 +27,7 @@ tests-single-ci:
 
 tests-single-local:
 	@if ! test -n "$(TEST_TARGET)" ; then echo "***ERROR*** Set TEST_TARGET=<your-module> or use make tests-all-local" ; return 1; fi
-	export PATH=./buildroot/bin/:./buildroot/tests/:${PATH} \
+	export PATH="./buildroot/bin/:./buildroot/tests/:${PATH}" \
 	  && export VERBOSE_PLATFORMIO=$(VERBOSE_PLATFORMIO) \
 	  && run_tests . $(TEST_TARGET) "$(ONLY_TEST)"
 .PHONY: tests-single-local
@@ -38,7 +38,7 @@ tests-single-local-docker:
 .PHONY: tests-single-local-docker
 
 tests-all-local:
-	export PATH=./buildroot/bin/:./buildroot/tests/:${PATH} \
+	export PATH="./buildroot/bin/:./buildroot/tests/:${PATH}" \
 	  && export VERBOSE_PLATFORMIO=$(VERBOSE_PLATFORMIO) \
 	  && for TEST_TARGET in $$(./get_test_targets.py) ; do echo "Running tests for $$TEST_TARGET" ; run_tests . $$TEST_TARGET ; done
 .PHONY: tests-all-local

Marlin/Configuration.h

@@ -496,7 +496,7 @@
  *    30 : 100kΩ  Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950
  *    60 : 100kΩ  Maker's Tool Works Kapton Bed Thermistor - beta 3950
  *    61 : 100kΩ  Formbot/Vivedino 350°C Thermistor - beta 3950
- *    66 : 4.7MΩ  Dyze Design High Temperature Thermistor
+ *    66 : 4.7MΩ  Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor
  *    67 : 500kΩ  SliceEngineering 450°C Thermistor
  *    68 : PT100 amplifier board from Dyze Design
  *    70 : 100kΩ  bq Hephestos 2
@@ -518,6 +518,7 @@
  *   110 : Pt100  with 1kΩ pullup (atypical)
  *   147 : Pt100  with 4.7kΩ pullup
  *  1010 : Pt1000 with 1kΩ pullup (atypical)
+ *  1022 : Pt1000 with 2.2kΩ pullup
  *  1047 : Pt1000 with 4.7kΩ pullup (E3D)
  *    20 : Pt100  with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage.
  *                NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21.
@@ -563,6 +564,10 @@
   #define MAX31865_SENSOR_OHMS_1      100
   #define MAX31865_CALIBRATION_OHMS_1 430
 #endif
+#if TEMP_SENSOR_IS_MAX_TC(2)
+  #define MAX31865_SENSOR_OHMS_2      100
+  #define MAX31865_CALIBRATION_OHMS_2 430
+#endif
 
 #if HAS_E_TEMP_SENSOR
   #define TEMP_RESIDENCY_TIME         10  // (seconds) Time to wait for hotend to "settle" in M109
@@ -874,7 +879,7 @@
 //#define POLARGRAPH
 #if ENABLED(POLARGRAPH)
   #define POLARGRAPH_MAX_BELT_LEN 1035.0
-  #define POLAR_SEGMENTS_PER_SECOND 5
+  #define DEFAULT_SEGMENTS_PER_SECOND 5
 #endif
 
 // @section delta
@@ -886,28 +891,28 @@
   // Make delta curves from many straight lines (linear interpolation).
   // This is a trade-off between visible corners (not enough segments)
   // and processor overload (too many expensive sqrt calls).
-  #define DELTA_SEGMENTS_PER_SECOND 200
+  #define DEFAULT_SEGMENTS_PER_SECOND 200
 
   // After homing move down to a height where XY movement is unconstrained
   //#define DELTA_HOME_TO_SAFE_ZONE
 
   // Delta calibration menu
-  // uncomment to add three points calibration menu option.
+  // Add three-point calibration to the MarlinUI menu.
   // See http://minow.blogspot.com/index.html#4918805519571907051
   //#define DELTA_CALIBRATION_MENU
 
-  // uncomment to add G33 Delta Auto-Calibration (Enable EEPROM_SETTINGS to store results)
+  // G33 Delta Auto-Calibration. Enable EEPROM_SETTINGS to store results.
   //#define DELTA_AUTO_CALIBRATION
 
-  // NOTE NB all values for DELTA_* values MUST be floating point, so always have a decimal point in them
-
   #if ENABLED(DELTA_AUTO_CALIBRATION)
-    // set the default number of probe points : n*n (1 -> 7)
+    // Default number of probe points : n*n (1 -> 7)
     #define DELTA_CALIBRATION_DEFAULT_POINTS 4
   #endif
 
+  // NOTE: All values for DELTA_* values MUST be floating point, so always have a decimal point in them
+
   #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU)
-    // Set the steprate for papertest probing
+    // Step size for paper-test probing
     #define PROBE_MANUALLY_STEP 0.05      // (mm)
   #endif
 
@@ -952,7 +957,7 @@
 //#define MP_SCARA
 #if EITHER(MORGAN_SCARA, MP_SCARA)
   // If movement is choppy try lowering this value
-  #define SCARA_SEGMENTS_PER_SECOND 200
+  #define DEFAULT_SEGMENTS_PER_SECOND 200
 
   // Length of inner and outer support arms. Measure arm lengths precisely.
   #define SCARA_LINKAGE_1 150       // (mm)
@@ -988,18 +993,18 @@
 // Enable for TPARA kinematics and configure below
 //#define AXEL_TPARA
 #if ENABLED(AXEL_TPARA)
-  #define DEBUG_ROBOT_KINEMATICS
-  #define ROBOT_SEGMENTS_PER_SECOND 200
+  #define DEBUG_TPARA_KINEMATICS
+  #define DEFAULT_SEGMENTS_PER_SECOND 200
 
   // Length of inner and outer support arms. Measure arm lengths precisely.
-  #define ROBOT_LINKAGE_1 120       // (mm)
-  #define ROBOT_LINKAGE_2 120       // (mm)
+  #define TPARA_LINKAGE_1 120       // (mm)
+  #define TPARA_LINKAGE_2 120       // (mm)
 
   // SCARA tower offset (position of Tower relative to bed zero position)
   // This needs to be reasonably accurate as it defines the printbed position in the SCARA space.
-  #define ROBOT_OFFSET_X    0       // (mm)
-  #define ROBOT_OFFSET_Y    0       // (mm)
-  #define ROBOT_OFFSET_Z    0       // (mm)
+  #define TPARA_OFFSET_X    0       // (mm)
+  #define TPARA_OFFSET_Y    0       // (mm)
+  #define TPARA_OFFSET_Z    0       // (mm)
 
   #define SCARA_FEEDRATE_SCALING  // Convert XY feedrate from mm/s to degrees/s on the fly
 
@@ -3058,7 +3063,7 @@
 //#define MKS_ROBIN_TFT_V1_1R
 
 //
-// 480x320, 3.5", FSMC Stock Display from TronxXY
+// 480x320, 3.5", FSMC Stock Display from Tronxy
 //
 //#define TFT_TRONXY_X5SA