Update some configs

config/examples/Anet/ET4+/Configuration_adv.h

@@ -1227,7 +1227,8 @@
     //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
     #define POWER_LOSS_STATE        LOW // State of pin indicating power loss
-    //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
+    //#define POWER_LOSS_PULLUP         // Set pullup / pulldown as appropriate for your sensor
+    //#define POWER_LOSS_PULLDOWN
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
 

config/examples/Creality/Ender-3/CrealityV422/Configuration_adv.h

@@ -854,8 +854,6 @@
 // If the Nozzle or Bed falls when the Z stepper is disabled, set its resting position here.
 //#define Z_AFTER_DEACTIVATE Z_HOME_POS
 
-//#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
-
 // Default Minimum Feedrates for printing and travel moves
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // (mm/s) Minimum feedrate. Set with M205 S.
 #define DEFAULT_MINTRAVELFEEDRATE     0.0     // (mm/s) Minimum travel feedrate. Set with M205 T.
@@ -1084,8 +1082,15 @@
   #if HAS_BED_PROBE
     //#define PROBE_OFFSET_WIZARD
     #if ENABLED(PROBE_OFFSET_WIZARD)
-      #define PROBE_OFFSET_WIZARD_START_Z -4.0   // Estimated nozzle-to-probe Z offset, plus a little extra
-      //#define PROBE_OFFSET_WIZARD_XY_POS XY_CENTER // Set a convenient position to do the measurement
+      //
+      // Enable to init the Probe Z-Offset when starting the Wizard.
+      // Use a height slightly above the estimated nozzle-to-probe Z offset.
+      // For example, with an offset of -5, consider a starting height of -4.
+      //
+      //#define PROBE_OFFSET_WIZARD_START_Z -4.0
+
+      // Set a convenient position to do the calibration (probing point and nozzle/bed-distance)
+      //#define PROBE_OFFSET_WIZARD_XY_POS { X_CENTER, Y_CENTER }
     #endif
   #endif
 
@@ -1222,7 +1227,8 @@
     //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
     //#define POWER_LOSS_PIN         44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
     //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
-    //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
+    //#define POWER_LOSS_PULLUP         // Set pullup / pulldown as appropriate for your sensor
+    //#define POWER_LOSS_PULLDOWN
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.