🚸 Improve Ender5 Plus (#739)

MarlinFirmware · May 28, 2022 · 40f3bbc · 40f3bbc
1 parent 1881008
commit 40f3bbc
Show file tree

Hide file tree

Showing 2 changed files with 32 additions and 32 deletions.
diff --git a/config/examples/Creality/Ender-5 Plus/Configuration.h b/config/examples/Creality/Ender-5 Plus/Configuration.h
@@ -723,7 +723,7 @@
  * heater. If your configuration is significantly different than this and you don't understand
  * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  */
-//#define PIDTEMPBED
+#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
@@ -744,9 +744,9 @@
 
   // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define DEFAULT_bedKp 10.00
-  #define DEFAULT_bedKi .023
-  #define DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKp 481.83
+  #define DEFAULT_bedKi 69.20
+  #define DEFAULT_bedKd 838.75
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED
@@ -823,7 +823,7 @@
  * Note: For Bowden Extruders make this large enough to allow load/unload.
  */
 #define PREVENT_LENGTHY_EXTRUDE
-#define EXTRUDE_MAXLENGTH 750
+#define EXTRUDE_MAXLENGTH 1500
 
 //===========================================================================
 //======================== Thermal Runaway Protection =======================
@@ -1288,7 +1288,7 @@
  *     O-- FRONT --+
  */
 // Note on Creality Ender-5 Plus: Z offset must be adjusted (M851) every time once the probe has been loosen/unmounted.
-#define NOZZLE_TO_PROBE_OFFSET { -44, -5, -3.0 }
+#define NOZZLE_TO_PROBE_OFFSET { -44, -5, -2.8 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
@@ -1298,10 +1298,10 @@
 #define XY_PROBE_FEEDRATE (133*60)
 
 // Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_FEEDRATE_FAST (15*60)
+#define Z_PROBE_FEEDRATE_FAST (4*60)
 
 // Feedrate (mm/min) for the "accurate" probe of each point
-#define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 4)
+#define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 2)
 
 /**
  * Probe Activation Switch
@@ -1377,7 +1377,7 @@
 #define Z_PROBE_OFFSET_RANGE_MAX 20
 
 // Enable the M48 repeatability test to test probe accuracy
-//#define Z_MIN_PROBE_REPEATABILITY_TEST
+#define Z_MIN_PROBE_REPEATABILITY_TEST
 
 // Before deploy/stow pause for user confirmation
 //#define PAUSE_BEFORE_DEPLOY_STOW
@@ -1687,13 +1687,13 @@
  * these options to restore the prior leveling state or to always enable
  * leveling immediately after G28.
  */
-#define RESTORE_LEVELING_AFTER_G28
-//#define ENABLE_LEVELING_AFTER_G28
+//#define RESTORE_LEVELING_AFTER_G28
+#define ENABLE_LEVELING_AFTER_G28
 
 /**
  * Auto-leveling needs preheating
  */
-//#define PREHEAT_BEFORE_LEVELING
+#define PREHEAT_BEFORE_LEVELING
 #if ENABLED(PREHEAT_BEFORE_LEVELING)
   #define LEVELING_NOZZLE_TEMP 120   // (°C) Only applies to E0 at this time
   #define LEVELING_BED_TEMP     50
@@ -1890,7 +1890,7 @@
 #endif
 
 // Homing speeds (linear=mm/min, rotational=°/min)
-#define HOMING_FEEDRATE_MM_M { (90*60), (90*60), (15*60) }
+#define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) }
 
 // Validate that endstops are triggered on homing moves
 #define VALIDATE_HOMING_ENDSTOPS

diff --git a/config/examples/Creality/Ender-5 Plus/Configuration_adv.h b/config/examples/Creality/Ender-5 Plus/Configuration_adv.h
@@ -473,7 +473,7 @@
  * Hotend Idle Timeout
  * Prevent filament in the nozzle from charring and causing a critical jam.
  */
-//#define HOTEND_IDLE_TIMEOUT
+#define HOTEND_IDLE_TIMEOUT
 #if ENABLED(HOTEND_IDLE_TIMEOUT)
   #define HOTEND_IDLE_TIMEOUT_SEC (5*60)    // (seconds) Time without extruder movement to trigger protection
   #define HOTEND_IDLE_MIN_TRIGGER   180     // (°C) Minimum temperature to enable hotend protection
@@ -908,7 +908,7 @@
    *
    * Set the default state here, change with 'M401 S' or UI, use M500 to save, M502 to reset.
    */
-  #define BLTOUCH_HS_MODE true
+  #define BLTOUCH_HS_MODE false
 
   // Safety: Enable voltage mode settings in the LCD menu.
   //#define BLTOUCH_LCD_VOLTAGE_MENU
@@ -2352,7 +2352,7 @@
  * Currently handles M108, M112, M410, M876
  * NOTE: Not yet implemented for all platforms.
  */
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
 
 /**
  * Realtime Reporting (requires EMERGENCY_PARSER)
@@ -2546,11 +2546,11 @@
 #define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
-  #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
+  #define PAUSE_PARK_RETRACT_LENGTH            5  // (mm) Initial retract.
                                                   // This short retract is done immediately, before parking the nozzle.
   #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     10  // (mm/s) Unload filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_UNLOAD_LENGTH      100  // (mm) The length of filament for a complete unload.
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH      700  // (mm) The length of filament for a complete unload.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
                                                   //   Set to 0 for manual unloading.
@@ -2559,7 +2559,7 @@
                                                   // 0 to disable start loading and skip to fast load only
   #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE   6  // (mm/s) Load filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_FAST_LOAD_ACCEL     25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH     0  // (mm) Load length of filament, from extruder gear to nozzle.
+  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH   670  // (mm) Load length of filament, from extruder gear to nozzle.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
   //#define ADVANCED_PAUSE_CONTINUOUS_PURGE       // Purge continuously up to the purge length until interrupted.
@@ -2569,7 +2569,7 @@
                                                   //   Filament can be extruded repeatedly from the Filament Change menu
                                                   //   until extrusion is consistent, and to purge old filament.
   #define ADVANCED_PAUSE_RESUME_PRIME          0  // (mm) Extra distance to prime nozzle after returning from park.
-  //#define ADVANCED_PAUSE_FANS_PAUSE             // Turn off print-cooling fans while the machine is paused.
+  #define ADVANCED_PAUSE_FANS_PAUSE             // Turn off print-cooling fans while the machine is paused.
 
                                                   // Filament Unload does a Retract, Delay, and Purge first:
   #define FILAMENT_UNLOAD_PURGE_RETRACT       13  // (mm) Unload initial retract length.
@@ -2583,11 +2583,11 @@
   //#define FILAMENT_CHANGE_RESUME_ON_INSERT      // Automatically continue / load filament when runout sensor is triggered again.
   //#define PAUSE_REHEAT_FAST_RESUME              // Reduce number of waits by not prompting again post-timeout before continuing.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
+  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
   //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
 
-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
-  //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
+  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif
 
 // @section tmc
@@ -3903,7 +3903,7 @@
 /**
  * Auto-report position with M154 S<seconds>
  */
-//#define AUTO_REPORT_POSITION
+#define AUTO_REPORT_POSITION
 
 /**
  * Include capabilities in M115 output
@@ -3958,11 +3958,11 @@
 //#define NO_WORKSPACE_OFFSETS
 
 // Extra options for the M114 "Current Position" report
-//#define M114_DETAIL         // Use 'M114` for details to check planner calculations
-//#define M114_REALTIME       // Real current position based on forward kinematics
+#define M114_DETAIL         // Use 'M114` for details to check planner calculations
+#define M114_REALTIME       // Real current position based on forward kinematics
 //#define M114_LEGACY         // M114 used to synchronize on every call. Enable if needed.
 
-//#define REPORT_FAN_CHANGE   // Report the new fan speed when changed by M106 (and others)
+#define REPORT_FAN_CHANGE   // Report the new fan speed when changed by M106 (and others)
 
 /**
  * Spend 28 bytes of SRAM to optimize the G-code parser
@@ -4125,12 +4125,12 @@
  * Host Prompt Support enables Marlin to use the host for user prompts so
  * filament runout and other processes can be managed from the host side.
  */
-//#define HOST_ACTION_COMMANDS
+#define HOST_ACTION_COMMANDS
 #if ENABLED(HOST_ACTION_COMMANDS)
-  //#define HOST_PAUSE_M76                // Tell the host to pause in response to M76
-  //#define HOST_PROMPT_SUPPORT           // Initiate host prompts to get user feedback
+  #define HOST_PAUSE_M76                // Tell the host to pause in response to M76
+  #define HOST_PROMPT_SUPPORT           // Initiate host prompts to get user feedback
   #if ENABLED(HOST_PROMPT_SUPPORT)
-    //#define HOST_STATUS_NOTIFICATIONS   // Send some status messages to the host as notifications
+    #define HOST_STATUS_NOTIFICATIONS   // Send some status messages to the host as notifications
   #endif
   //#define HOST_START_MENU_ITEM          // Add a menu item that tells the host to start
   //#define HOST_SHUTDOWN_MENU_ITEM       // Add a menu item that tells the host to shut down
@@ -4141,7 +4141,7 @@
  *
  * Implement M486 to allow Marlin to skip objects
  */
-//#define CANCEL_OBJECTS
+#define CANCEL_OBJECTS
 #if ENABLED(CANCEL_OBJECTS)
   #define CANCEL_OBJECTS_REPORTING // Emit the current object as a status message
 #endif