Update Kconfig

config/printer-Artillery-Sidewinder-X3-Plus-2024.cfg

@@ -0,0 +1,237 @@
+# For the Artillery Sidewinder X3 Pro/Plus that came factory installed with V1.29 firmware, follow these steps.
+#   - Compile with the processor model STM32F401.
+#   - Select the 48KiB bootloader,
+#   - Select USB PA11/PA12 for USB communication interface.
+#   - Select USART2 PA3/PA2 for UART communication via the Wi-Fi Tx/Rx pins
+# To set 48KiB bootloader, you need to make a change to make menuconfig Kconfig file
+# Here is a link to a how-to video: https://youtu.be/dpc76zN7Dh0
+# Rename klipper.bin to yuntu.bin
+# Copy the file out/yuntu.bin to an SD card and then restart the printer with that SD card
+#
+# For models that did not come with V1.29 installed
+#   - Compile with the processor model STM32F401.
+#   - Select the NO BOOTLOADER
+#   - Select USB PA11/PA12 for USB communication interface.
+#   - Select USART2 PA3/PA2 for UART communication via the Wi-Fi Tx/Rx pins
+#   - quit, save, make
+#   - Connect your printer to a computer running Pronterface, Octoprint, Repetier, BedLeveler5000 (anything with Console capability)
+#   - Power on the machine and send M997 through console into Marlin, this will put the board into "DFU" mode
+#   - DO NOT TURN OFF THE PRINTER
+#   - Connect your Linux/Klipper device to the USB port
+#   - Run lsusb and verify that the STM32 DFU device is visible (Bus 001 Device 006: ID 0483:df11 STMicroelectronics STM Device in DFU Mode)
+#   - Run sudo make flash 0483:df11
+#   - Run lsusb again and there should be two devices:
+#        Bus 001 Device 007: ID 1d50:614e OpenMoko, Inc. stm32f401xc
+#        Bus 001 Device 003: ID 0cf3:e010 Qualcomm Atheros Communications stm32f401xc
+# See docs/Config_Reference.md for a description of parameters.
+
+[mcu]
+serial: /dev/ttyACM0
+restart_method: command
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 15
+max_z_accel: 100
+square_corner_velocity: 5
+# Use these higher values just to configure Input Shaper
+#max_accel: 10000
+#max_accel_to_decel: 10000
+
+[led LED_Light]
+white_pin: PC2
+initial_white: 1.0
+
+[neopixel hotend_neopixel]
+pin: PD2
+color_order: GRB
+initial_RED: 1.0
+initial_GREEN: 1.0
+initial_BLUE: 1.0
+
+[force_move]
+enable_force_move: True
+
+[stepper_x]
+step_pin: PA8
+dir_pin: PC9
+enable_pin: !PA15
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PB9
+position_min: 0
+position_endstop: 0
+position_max: 315
+homing_speed: 50
+
+[stepper_y]
+step_pin: PC7
+dir_pin: !PC6
+enable_pin: !PC8
+microsteps: 16
+rotation_distance: 40
+endstop_pin: !PB8
+position_endstop: 0
+position_max: 315
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB10
+dir_pin: !PA4
+enable_pin: !PC4
+rotation_distance: 8
+microsteps: 16
+position_min: -1
+position_max: 400
+endstop_pin: probe:z_virtual_endstop # Use Z- as endstop
+#homing_speed: 10.0
+
+[extruder]
+max_extrude_only_distance: 100.0
+step_pin: PC11
+dir_pin: !PC10
+enable_pin: !PC12
+microsteps: 64
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA6
+sensor_type: EPCOS 100K B57560G104F #Generic 3950
+sensor_pin: PC5
+min_extrude_temp: 170
+min_temp: 0
+max_temp: 300
+# Calibrate E-Steps https://www.klipper3d.org/Rotation_Distance.html#calibrating-rotation_distance-on-extruders
+rotation_distance: 17.75
+# Calibrate PID: https://www.klipper3d.org/Config_checks.html#calibrate-pid-settings
+#  - Example: PID_CALIBRATE HEATER=extruder TARGET=200
+#control = pid
+#pid_kp = 30.356
+#pid_ki = 1.857
+#pid_kd = 124.081
+# Calibrate PA: https://www.klipper3d.org/Pressure_Advance.html
+
+[heater_bed]
+heater_pin: PA7
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC0
+max_temp: 100
+min_temp: 0
+# Calibrate PID: https://www.klipper3d.org/Config_checks.html#calibrate-pid-settings
+#  - Example: PID_CALIBRATE HEATER=heater_bed TARGET=60
+#control = pid
+#pid_kp = 64.230
+#pid_ki = 0.723
+#pid_kd = 1425.905
+
+[heater_fan hotend_fan]
+pin: PB1
+heater: extruder
+heater_temp: 50.0
+
+[fan]
+pin: PB0
+
+[temperature_fan Artillery_MCU]
+sensor_type: temperature_mcu
+pin: PA5
+max_temp: 60.0
+target_temp: 40.0
+min_temp: 0
+shutdown_speed: 0.0
+kick_start_time: 0.5
+off_below: 0.19
+max_speed: 1.0
+min_speed: 0.0
+control: watermark
+#pid_Kp: 2.0
+#pid_Ki: 5.0
+#pid_Kd: 0.5
+#pid_deriv_time: 2.0
+
+[filament_switch_sensor filament_sensor]
+pause_on_runout: true
+switch_pin: PC1
+
+[probe]
+pin: PC14
+x_offset:45.2
+y_offset:11.6
+speed:5
+lift_speed:15
+#samples:
+#sample_retract_dist:
+#samples_result:
+#samples_tolerance:
+#samples_tolerance_retries:
+
+[safe_z_home]
+home_xy_position: 110, 145 #   X, Y coordinate (e.g. 100, 100) where the Z homing should be
+speed: 300.0
+z_hop: 10
+z_hop_speed: 15.0
+
+[bed_mesh]
+speed: 300
+horizontal_move_z: 6
+mesh_min: 46,15
+mesh_max: 300,300
+probe_count: 10, 10
+fade_start: 1.0
+fade_end: 0.0
+#fade_target:
+#   The z position in which fade should converge. When this value is
+#   set to a non-zero value it must be within the range of z-values in
+#   the mesh. Users that wish to converge to the z homing position
+#   should set this to 0. Default is the average z value of the mesh.
+#split_delta_z: .025
+#   The amount of Z difference (in mm) along a move that will trigger
+#   a split. Default is .025.
+#move_check_distance: 5.0
+#   The distance (in mm) along a move to check for split_delta_z.
+#   This is also the minimum length that a move can be split. Default
+#   is 5.0.
+#mesh_pps: 2, 2
+#   A comma separated pair of integers X, Y defining the number of
+#   points per segment to interpolate in the mesh along each axis. A
+#   "segment" can be defined as the space between each probed point.
+#   The user may enter a single value which will be applied to both
+#   axes. Default is 2, 2.
+algorithm: bicubic
+#   The interpolation algorithm to use. May be either "lagrange" or
+#   "bicubic". This option will not affect 3x3 grids, which are forced
+#   to use lagrange sampling. Default is lagrange.
+#bicubic_tension: .2
+#   When using the bicubic algorithm the tension parameter above may
+#   be applied to change the amount of slope interpolated. Larger
+#   numbers will increase the amount of slope, which results in more
+#   curvature in the mesh. Default is .2.
+#relative_reference_index:
+#   A point index in the mesh to reference all z values to. Enabling
+#   this parameter produces a mesh relative to the probed z position
+#   at the provided index.
+#faulty_region_1_min:
+#faulty_region_1_max:
+#   Optional points that define a faulty region.  See docs/Bed_Mesh.md
+#   for details on faulty regions.  Up to 99 faulty regions may be added.
+#   By default no faulty regions are set.
+
+[screws_tilt_adjust]
+screw1: 120, 153
+screw1_name: center reference
+screw2: 7, 45
+screw2_name: front left
+screw3: 210, 45
+screw3_name: front right
+screw4: 227, 145
+screw4_name: right center
+screw5: 210, 245
+screw5_name: rear right
+screw6: 7, 245
+screw6_name: rear left
+screw7: 7, 145
+screw7_name: left center
+horizontal_move_z: 8
+speed: 300
+screw_thread: CW-M4

src/stm32/Kconfig

@@ -288,7 +288,7 @@ choice
     config STM32_FLASH_START_9000
         bool "36KiB bootloader" if MACH_STM32F1
     config STM32_FLASH_START_C000
-        bool "48KiB bootloader" if MACH_STM32F4x5
+        bool "48KiB bootloader" if MACH_STM32F4x5 || MACH_STM32F401
     config STM32_FLASH_START_10000
         bool "64KiB bootloader" if MACH_STM32F103 || MACH_STM32F4