-
-
Notifications
You must be signed in to change notification settings - Fork 5.4k
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
config: Add config for printer Creality CR10s Pro V2 (#6300)
Created a base config for the Creality CR10s Pro v2 as described here: https://www.creality.com/products/cr-10s-pro-v2-3d-printer This will allow users with this printer to more easily setup Klipper firmware. Signed-off-by: Peter Kydas <[email protected]>
- Loading branch information
1 parent
dd368c1
commit 15c3824
Showing
2 changed files
with
155 additions
and
0 deletions.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change |
|---|---|---|
| @@ -0,0 +1,154 @@ | ||
| # This file contains pin mappings for the Creality CR-10S Pro V2. To use | ||
| # this config, the firmware should be compiled for the AVR atmega2560. | ||
|
|
||
| # See docs/Config_Reference.md for a description of parameters. | ||
|
|
||
| ## General Config | ||
| [mcu] | ||
| serial: /dev/serial/by-id/<YOUR_USB_ID> | ||
|
|
||
| [printer] | ||
| kinematics: cartesian | ||
| max_velocity: 200 | ||
| max_accel: 1500 | ||
| max_z_velocity: 10 | ||
| max_z_accel: 100 | ||
|
|
||
| ## Stepper Motors and Extruder | ||
| [stepper_x] | ||
| step_pin: PF0 #ar54 | ||
| dir_pin: PF1 #ar55 | ||
| enable_pin: !PD7 #!ar38 | ||
| rotation_distance: 40 | ||
| microsteps: 16 | ||
| full_steps_per_rotation: 200 | ||
| endstop_pin: ^PE5 #^ar3 | ||
| position_endstop: 0 | ||
| position_min: 0 | ||
| position_max: 300 | ||
| homing_speed: 50 | ||
| homing_retract_dist: 5 | ||
|
|
||
| [stepper_y] | ||
| step_pin: PF6 #ar60 | ||
| dir_pin: !PF7 #ar61 | ||
| enable_pin: !PF2 #!ar56 | ||
| rotation_distance: 40 | ||
| microsteps: 16 | ||
| full_steps_per_rotation: 200 | ||
| endstop_pin: ^PJ1 #^ar14 | ||
| position_endstop: 0 | ||
| position_min: 0 | ||
| position_max: 310 | ||
| homing_speed: 50 | ||
| homing_retract_dist: 5 | ||
|
|
||
| [stepper_z] | ||
| step_pin: PL3 #ar46 | ||
| dir_pin: !PL1 #!ar48 | ||
| enable_pin: !PK0 #!ar62 | ||
| rotation_distance: 8 | ||
| microsteps: 16 | ||
| full_steps_per_rotation: 200 | ||
| endstop_pin: probe:z_virtual_endstop | ||
| position_min: -3 | ||
| position_max: 363 # you can go higher but then the cables crimp | ||
|
|
||
| [extruder] | ||
| step_pin: PA4 # ar26 | ||
| dir_pin: PA6 # !ar28 | ||
| enable_pin: !PA2 # !ar24 | ||
| rotation_distance: 22.900 | ||
| microsteps: 16 | ||
| full_steps_per_rotation: 200 | ||
| nozzle_diameter: 0.400 | ||
| filament_diameter: 1.750 | ||
| max_extrude_only_distance: 500.0 | ||
| max_extrude_only_velocity: 70.0 | ||
| max_extrude_only_accel: 1000.0 | ||
| heater_pin: PB4 #ar10 | ||
| sensor_type: EPCOS 100K B57560G104F | ||
| sensor_pin: PK5 #analog13 | ||
| control: pid #calibrated in Klipper, you will need to run this for your machine | ||
| pid_kp: 28.359 | ||
| pid_ki: 1.616 | ||
| pid_kd: 124.426 | ||
| min_extrude_temp: 170 | ||
| min_temp: 5 | ||
| max_temp: 275 | ||
|
|
||
| [fan] | ||
| pin: PH6 #ar9 | ||
|
|
||
| [heater_bed] | ||
| heater_pin: PH5 #ar8 | ||
| sensor_type: EPCOS 100K B57560G104F | ||
| sensor_pin: PK6 #analog14 | ||
| control: pid #calibrated in Klipper, you will need to run this for your machine | ||
| pid_kp: 70.936 | ||
| pid_ki: 1.151 | ||
| pid_kd: 1093.298 | ||
| min_temp: 5 | ||
| max_temp: 140 | ||
|
|
||
| ## BLTouch and Safe Z Settings | ||
| [bltouch] | ||
| sensor_pin: ^PD2 | ||
| control_pin: PB5 | ||
| stow_on_each_sample: False # Be careful | ||
| probe_with_touch_mode: True | ||
| x_offset: -27 | ||
| y_offset: -2 | ||
| z_offset: 2 # you will need to calibrate this in Klipper | ||
| speed: 4.0 | ||
| samples: 2 | ||
| sample_retract_dist: 3.0 | ||
|
|
||
| [safe_z_home] | ||
| home_xy_position: 177,155 | ||
| speed: 80.0 | ||
| z_hop: 10.0 | ||
| z_hop_speed: 5.0 | ||
|
|
||
| [bed_mesh] | ||
| speed: 120 | ||
| horizontal_move_z: 5 | ||
| mesh_min: 5, 5 | ||
| mesh_max: 268, 305 | ||
| probe_count: 5,5 | ||
| fade_start: 1 | ||
| fade_end: 10 | ||
|
|
||
| [filament_switch_sensor e0_sensor] | ||
| switch_pin: PE4 #ar2 | ||
| pause_on_runout: False | ||
| runout_gcode: | ||
| PAUSE_PARK | ||
|
|
||
| ## Calibrating the Bed | ||
| # this is for the bltouch to calibrate the bed | ||
| [screws_tilt_adjust] | ||
| screw1: 40,40 | ||
| screw1_name: front left screw | ||
| screw2: 295,40 | ||
| screw2_name: front right screw | ||
| screw3: 295,280 | ||
| screw3_name: rear right screw | ||
| screw4: 40,280 | ||
| screw4_name: rear left screw | ||
| speed: 50 | ||
| horizontal_move_z: 10 | ||
| screw_thread: CW-M3 | ||
|
|
||
| [bed_screws] | ||
| screw1: 13,38 | ||
| screw1_name: front left screw | ||
| screw2: 268,38 | ||
| screw2_name: front right screw | ||
| screw3: 268,278 | ||
| screw3_name: rear right screw | ||
| screw4: 13,38 | ||
| screw4_name: rear left screw | ||
| horizontal_move_z: 5 | ||
|
|
||
| [pause_resume] |
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters