Main Board v4.3.1 Display boad v1.4 #2007
Replies: 4 comments 5 replies
-
|
Hi Canadian, where are you located I may be able to help you |
Beta Was this translation helpful? Give feedback.
-
|
Ontario canada
…On Wed., Aug. 10, 2022, 6:41 p.m. carioca53, ***@***.***> wrote:
Hi Canadian, where are you located I may be able to help you
—
Reply to this email directly, view it on GitHub
<#2007 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/A2PAYEJ55J7AZVE6OJBI55TVYQVYJANCNFSM56GBBQGA>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
I am in Uxbridge, ON |
Beta Was this translation helpful? Give feedback.
-
|
St Mary's Here. This is the mother board. i use to updating firmware and i Know if i install the wrong update it will brick the unit |
Beta Was this translation helpful? Give feedback.
-
|
It appears the 4.3.1 board is comparable to a 4.2.2 board on the Ender 3V2. You should be able to use 4.2.2 version firmware on this board without an issue. the 4.3.1 board isn't a good board, it's a lesser version of the 4.2.2 board so I would recommend getting a 4.2.7 board, you will have more options for firmware with the 4.2.7 board. There is a version of Jyers from Jan 21/22 that should work but you have to compile your own firmware, I can compile a copy for you but would rather do it via emails. |
Beta Was this translation helpful? Give feedback.
-
|
Thank you for the help. I was able to find a firmware that worked. Mriscoc
Professional Firmware. I will update the board more then likely soon.
Thank you again for the quick response and help. I found the answer also
on credulity ender 3 v2 Facebook page.
…On Thu., Aug. 11, 2022, 2:51 p.m. carioca53, ***@***.***> wrote:
It appears the 4.3.1 board is comparable to a 4.2.2 board on the Ender
3V2. You should be able to use 4.2.2 version firmware on this board without
an issue. the 4.3.1 board isn't a good board, it's a lesser version of the
4.2.2 board so I would recommend getting a 4.2.7 board, you will have more
options for firmware with the 4.2.7 board. There is a version of Jyers from
Jan 21/22 that should work but you have to compile your own firmware, I can
compile a copy for you but would rather do it via emails.
—
Reply to this email directly, view it on GitHub
<#2007 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/A2PAYEMJ5A5V2YBPRLTTF33VYVDUNANCNFSM56GBBQGA>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
Good choice with Mriscoc pro firmware, very reliable, I loaded in my grandson E3V2, works perfectly with lots of options. |
Beta Was this translation helpful? Give feedback.
-
|
I'm just running my first print right now. Since my wife said I can buy it
I'm making the owl for her . Happy wife is a happy hubby.
…On Thu., Aug. 11, 2022, 8:24 p.m. carioca53, ***@***.***> wrote:
Good choice with Mriscoc pro firmware, very reliable, I loaded in my
grandson E3V2, works perfectly with lots of options.
—
Reply to this email directly, view it on GitHub
<#2007 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/A2PAYEKC2IGBMAGYE43IAILVYWKT5ANCNFSM56GBBQGA>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
after 43 years I can attest to happy wife is a happy hubby. |
Beta Was this translation helpful? Give feedback.
-
I just bought an Ender 3 v2 I also installed the CR touch i am look to flash the firmware but i don't see on that will work with my version . IF any one can help me out that would be great. Thanks
Beta Was this translation helpful? Give feedback.
All reactions