The EspoTek Labrador is an open-source board that turns your PC, Raspberry Pi or Android Smartphone and into a full-featured electronics lab bench, complete with oscilloscope, signal generator and more.
This repo hosts all of the software and hardware that makes Labrador possible.
If you're new to Labrador or oscilloscopes in general, I strongly recommend checking out the fantastic tutorial series produced by Lief Koepsel:
https://www.wellys.com/posts/courses_electronics/
It features well-written, rich articles as well as video content that explains everything more clearly than I ever could!
To download binary (executable) versions of the software, go to:
https://github.com/espotek/labrador/releases
For the documentation, please visit:
https://github.com/espotek/labrador/wiki
Please note that the 32-bit version of Raspbian version 9 (Stretch) or later is required to install this software.
To install Labrador on the Raspberry Pi, open a terminal and paste the following command:
wget -O /tmp/labrador_bootstrap_pi https://raw.githubusercontent.com/EspoTek/Labrador/master/labrador_bootstrap_pi && sudo chmod +x /tmp/labrador_bootstrap_pi && sudo /tmp/labrador_bootstrap_pi
This will automatically download, compile and install the latest version of the Labrador software from source. The whole process will take around 20-30 minutes, so don't forget to pack a snack!
After running it, a desktop entry will appear for the Labrador software (under Education), and running the labrador command from the terminal will launch the software interface.
There are community contributed 3D printable cases available at Thingiverse, courtesy of SpaceBex and Bostwickenator:
-
Dave Messink has designed a case that can be laser cut from 3mm plywood
The binding posts and cables he used are from Amazon.
https://www.amazon.com/dp/B07YKYP8MN?psc=1&ref=ppx_yo2ov_dt_b_product_details
https://www.amazon.com/dp/B08KZGPTLM?ref=ppx_yo2ov_dt_b_product_details&th=1
https://www.amazon.com/dp/B08KZGPTLM?ref=ppx_yo2ov_dt_b_product_details&th=1
If you're looking to build from source but don't know where to start, Qt Creator is the easiest way to get your toes wet!
https://www.qt.io/download-open-source/
When installing, make sure you tick the box to install Qt 5.15 or later.
Once it's installed, open Desktop_Interface/Labrador.pro, then Clean All -> Run qmake -> Build All.
If you're on Linux (including Raspberry Pi), then you can also build the software from source by cloning the repo, cd'ing to the Desktop_Interface directory then running:
qmake
make
sudo make install
Then, to launch, just type labrador into the terminal.
On Macos, additional steps may be required. See issue #238
To build the AVR software, I use Atmel Studio 7. Just load up the .atsln and push F7. You can use avr-gcc if you don't want to install a full IDE.
The PCB files can be edited in KiCAD 5.0 or later.
All Dekstop software files are licenced under GNU GPL v3. https://www.gnu.org/licenses/gpl.html
All Microcontroller software files, with the exception of those provided by Atmel, are licenced under the 3-Clause BSD License. https://opensource.org/licenses/BSD-3-Clause
All hardware files (schematics, PCB) are licenced under Creative Commons 4.0 (CC BY-NC-SA). https://creativecommons.org/licenses/by-nc-sa/4.0/
If you want to submit a Pull Request, bug report or feature request please feel free to do so here at GitHub.
If you just want to say hello and remind me that people are actually using my product (or if you just don't want to make a GitHub account), please email [email protected]
Thanks to all.
~Chris