Replies: 5 comments 2 replies
-
|
https://github.com/realA10001986/Time-Circuits-Display/tree/main#speedometer |
Beta Was this translation helpful? Give feedback.
-
|
Hi, here is a video, could you please tell me where I am wrong? VIDEO-2024-06-14-13-40-54.mov |
Beta Was this translation helpful? Give feedback.
-
|
The thing is that I do have the green adapter that is on the speedo green connector on the control panel. So, I did the wiring both sides of the cable. But But when I plug the both sides to the speedometer and the control panel, the TCD stops working and seems to be blocked as you can see on the video attached. And I chose “circuit setups.us” as speedo display type though |
Beta Was this translation helpful? Give feedback.
-
You won't need the adapter. Earlier versions of the control board did not have the green connector on the PCB. Plug in the Speedo before turning everything on. It reads if it is there or not on power up. Also, it's hard to tell but I think you have the orange/white wires switched. Pin 2 (from the left) should be orange with white stripe. Pin 4 should be white with orange stripe. |
Beta Was this translation helpful? Give feedback.
-
|
Yes!!! I did not see the différence between the orange/white wires!Now it works perfectly! :-)))Thanks a lot for your help ! Best regards GabinLe 14 juin 2024 à 14:58, John ***@***.***> a écrit :
The thing is that I do have the green adapter that is on the speedo green connector on the control panel. So, I did the wiring both sides of the cable. But But when I plug the both sides to the speedometer and the control panel, the TCD stops working and seems to be blocked as you can see on the video attached.
And I chose “circuit setups.us” as speedo display type though
You won't need the adapter. Earlier versions of the control board did not have the green connector on the PCB.
Plug in the Speedo before turning everything on. It reads if it is there or not on power up.
Also, it's hard to tell but I think you have the orange/white wires switched. Pin 2 (from the left) should be orange with white stripe. Pin 4 should be white with orange stripe.
—Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you authored the thread.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
|
Hi John,
I’ve just realized I lost the the plastic bag containing the « set, to, 88 » stickers….
Could you please, send it again for me please?
Of course I pay the shipment, as I live in France.
Let me know.
Best regards,
Gabin
… Le 14 juin 2024 à 17:28, Gabin Lesieur ***@***.***> a écrit :
Yes!!!
I did not see the différence between the orange/white wires!
Now it works perfectly! :-)))
Thanks a lot for your help !
Best regards
Gabin
> Le 14 juin 2024 à 14:58, John ***@***.***> a écrit :
>
>
>
> The thing is that I do have the green adapter that is on the speedo green connector on the control panel. So, I did the wiring both sides of the cable. But But when I plug the both sides to the speedometer and the control panel, the TCD stops working and seems to be blocked as you can see on the video attached.
>
> And I chose “circuit setups.us <http://setups.us/>” as speedo display type though
>
> You won't need the adapter. Earlier versions of the control board did not have the green connector on the PCB.
>
> Plug in the Speedo before turning everything on. It reads if it is there or not on power up.
>
> Also, it's hard to tell but I think you have the orange/white wires switched. Pin 2 (from the left) should be orange with white stripe. Pin 4 should be white with orange stripe.
>
> —
> Reply to this email directly, view it on GitHub <#49 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BEW6UTHI3BR7W6KRUMWEJIDZHLSFPAVCNFSM6AAAAABJCHABA6VHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TONZUGQ4DC>.
> You are receiving this because you authored the thread.
>
|
Beta Was this translation helpful? Give feedback.
-
|
anyone? :) |
Beta Was this translation helpful? Give feedback.
-
Hi everyone, how do you connect the speedometer to the TCD please? The ending of the cable is a XH 4 pin and I can see that the Speedometer borner on the TCD is a green block.. How does it work please? Is there any changes to apply on the web portal? Thanks a lot for your help, Regards
Beta Was this translation helpful? Give feedback.
All reactions