Terway CNI Network Plugin

CNI plugin for Alibaba Cloud VPC/ENI

English | 简体中文

Try It

Install Kubernetes

Prepare Aliyun ECS instance. The ECS OS we tested is Centos 7.4/7.6.
Install Kubernetes via kubeadm: create-cluster-kubeadm

After setup kubernetes cluster.

Change iptables Forward default policy to ACCEPT on every node of cluster: iptables -P FORWARD ACCEPT.
Check the rp_filter in sysctl parameters, set them to "0" on every node of cluster.

Make sure cluster up and healthy by kubectl get cs.

Install Terway network plugin

Terway plugin have two installation modes

VPC Mode

VPC Mode, Using `Aliyun VPC` route table to connect the pods. Can assign dedicated ENI to Pod. Install method: <br />
Replace `Network` and `access_key/access_secret` in [terway.yml](./terway.yml) with your cluster pod subnet and aliyun openapi credentials. Then use `kubectl apply -f terway.yml` to install Terway into kubernetes cluster.

ENI Secondary IP Mode

ENI Secondary IP Mode, Using `Aliyun ENI's secondary ip` to connect the pods. This mode not limited by VPC route tables quotation. Install method: <br />
Replace `access_key/access_secret` and `security_group/vswitches` in [terway-multiip.yml](./terway-multiip.yml) with your aliyun openapi credentials and resources id. Then use `kubectl apply -f terway-multiip.yml` to install Terway into kubernetes cluster.

Terway requires the access_key have following RAM Permissions

{
  "Version": "1",
  "Statement": [
    {
      "Action": [
        "ecs:CreateNetworkInterface",
        "ecs:DescribeNetworkInterfaces",
        "ecs:AttachNetworkInterface",
        "ecs:DetachNetworkInterface",
        "ecs:DeleteNetworkInterface",
        "ecs:DescribeInstanceAttribute",
        "ecs:DescribeInstanceTypes",
        "ecs:AssignPrivateIpAddresses",
        "ecs:UnassignPrivateIpAddresses",
        "ecs:DescribeInstances",
        "ecs:ModifyNetworkInterfaceAttribute"
      ],
      "Resource": [
        "*"
      ],
      "Effect": "Allow"
    },
    {
      "Action": [
        "vpc:DescribeVSwitches"
      ],
      "Resource": [
        "*"
      ],
      "Effect": "Allow"
    }
  ]
}

Using kubectl get ds terway -n kube-system to watch plugin launching. Plugin install completed while terway daemonset available pods equal to nodes.

Terway network plugin usage

Vpc network container

On VPC installation mode, Terway will config pod's address using node's podCidr when pod not have any special config. eg:

[root@iZj6c86lmr8k9rk78ju0ncZ ~]# kubectl run -it --rm --image busybox busybox
If you don't see a command prompt, try pressing enter.
/ # ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
3: eth0@if7: <BROADCAST,MULTICAST,UP,LOWER_UP,M-DOWN> mtu 1500 qdisc noqueue
    link/ether 46:02:02:6b:65:1e brd ff:ff:ff:ff:ff:ff
/ # ip addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
3: eth0@if7: <BROADCAST,MULTICAST,UP,LOWER_UP,M-DOWN> mtu 1500 qdisc noqueue
    link/ether 46:02:02:6b:65:1e brd ff:ff:ff:ff:ff:ff
    inet 172.30.0.4/24 brd 172.30.0.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::4402:2ff:fe6b:651e/64 scope link
       valid_lft forever preferred_lft forever

Using ENI network interface to get the performance equivalent to the underlying network

On VPC installation mode, Config eni request aliyun/eni: 1 in one container of pod. The following example will create an Nginx Pod and assign an ENI:

apiVersion: v1
kind: Pod
metadata:
  name: nginx
spec:
  containers:
    - name: nginx
      image: nginx
      resources:
        limits:
          aliyun/eni: 1

[root@iZj6c86lmr8k9rk78ju0ncZ ~]# kubectl exec -it nginx sh
# ip addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UNKNOWN qlen 1000
    link/ether 00:16:3e:02:38:05 brd ff:ff:ff:ff:ff:ff
    inet 172.31.80.193/20 brd 172.31.95.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::216:3eff:fe02:3805/64 scope link
       valid_lft forever preferred_lft forever
4: veth1@if8: <BROADCAST,MULTICAST,UP,LOWER_UP,M-DOWN> mtu 1500 qdisc noqueue state UP
    link/ether 1e:60:c7:cb:1e:0e brd ff:ff:ff:ff:ff:ff
    inet6 fe80::1c60:c7ff:fecb:1e0e/64 scope link
       valid_lft forever preferred_lft forever

ENI Secondary IP Pod

On ENI secondary IP installation mode, Terway will create & allocate ENI secondary IP for pod. The IP of pod will in same IP Range:

[root@iZj6c86lmr8k9rk78ju0ncZ ~]# kubectl get pod -o wide
NAME                     READY   STATUS    RESTARTS   AGE   IP              NODE                                 NOMINATED NODE
nginx-64f497f8fd-ckpdm   1/1     Running   0          4d    192.168.0.191   cn-hangzhou.i-j6c86lmr8k9rk78ju0nc   <none>
[root@iZj6c86lmr8k9rk78ju0ncZ ~]# kubectl get node -o wide cn-hangzhou.i-j6c86lmr8k9rk78ju0nc
NAME                                 STATUS   ROLES    AGE   VERSION   INTERNAL-IP     EXTERNAL-IP   OS-IMAGE                KERNEL-VERSION              CONTAINER-RUNTIME
cn-hangzhou.i-j6c86lmr8k9rk78ju0nc   Ready    <none>   12d   v1.11.5   192.168.0.154   <none>        CentOS Linux 7 (Core)   3.10.0-693.2.2.el7.x86_64   docker://17.6.2
[root@iZj6c86lmr8k9rk78ju0ncZ ~]# kubectl exec -it nginx-64f497f8fd-ckpdm bash
root@nginx-64f497f8fd-ckpdm:/# ip addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
3: eth0@if106: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default
    link/ether 4a:60:eb:97:f4:07 brd ff:ff:ff:ff:ff:ff link-netnsid 0
    inet 192.168.0.191/32 brd 192.168.0.191 scope global eth0
       valid_lft forever preferred_lft forever

Using network policy to limit accessible between containers

The Terway plugin is compatible with NetworkPolicy in the standard K8S to control access between containers, for example:

Create and expose an deployment for test

[root@iZbp126bomo449eksjknkeZ ~]# kubectl run nginx --image=nginx --replicas=2
deployment "nginx" created
[root@iZbp126bomo449eksjknkeZ ~]# kubectl expose deployment nginx --port=80
service "nginx" exposed

Run busybox to test connection to deployment:

[root@iZbp126bomo449eksjknkeZ ~]# kubectl run busybox --rm -ti --image=busybox /bin/sh
If you don't see a command prompt, try pressing enter.
/ # wget --spider --timeout=1 nginx
Connecting to nginx (172.21.0.225:80)
/ #

Config network policy，only allow pod access which have run: nginx label:

kind: NetworkPolicy
apiVersion: networking.k8s.io/v1
metadata:
  name: access-nginx
spec:
  podSelector:
  matchLabels:
    run: nginx
  ingress:
  - from:
  - podSelector:
    matchLabels:
      access: "true"

The Pod access service without the specified label is rejected, and the container of the specified label can be accessed normally.

[root@iZbp126bomo449eksjknkeZ ~]# kubectl run busybox --rm -ti --image=busybox /bin/sh
If you don't see a command prompt, try pressing enter.
/ # wget --spider --timeout=1 nginx
Connecting to nginx (172.21.0.225:80)
wget: download timed out
/ #

[root@iZbp126bomo449eksjknkeZ ~]# kubectl run busybox --rm -ti --labels="access=true" --image=busybox /bin/sh
If you don't see a command prompt, try pressing enter.
/ # wget --spider --timeout=1 nginx
Connecting to nginx (172.21.0.225:80)
/ #

Limit container in/out bandwidth

The Terway network plugin can limit the container's traffic via limit policy in pod's annotations. For example:

apiVersion: v1
kind: Pod
metadata:
  name: nginx
  annotations:
    kubernetes.io/ingress-bandwidth: 10M
    kubernetes.io/egress-bandwidth: 10M
spec:
  nodeSelector:
    kubernetes.io/hostname: cn-shanghai.i-uf63p6s96kf4jfh8wpwn
  containers:
    - name: nginx
      image: nginx:1.7.9
      ports:
        - containerPort: 80

Build Terway

Prerequisites:

Docker >= 17.05 with multi-stage build

docker build -t acs/terway:latest .

Test

unit test:

git clone https://github.com/AliyunContainerService/terway.git
docker run -i --rm \
  -v $(pwd)/terway:/go/src/github.com/AliyunContainerService/terway \
  -w /go/src/github.com/AliyunContainerService/terway \
  sunyuan3/gometalinter:v1 bash -c "go test -race ./..."

function test:

export KUBECONFIG=$HOME/.kube/config  # path to your kubeconfig file
cd terway/tests
go test -tags e2e -timeout 30m0s -v ./ 
  -args -trunk=true/false -policy=true/false

example:

go test -tags e2e -timeout 30m0s -v ./ 
  -args -trunk=false -policy=false

Contribute

You are welcome to make new issues and pull requests.

Built With

Felix: Terway's NetworkPolicy is implemented by integrating ProjectCalico's Felix components. Felix watch NetworkPolicy configuration and config ACL rules on container veth.

Cilium: In the IPvlan mode, Terway integrate Cilium components to support NetworkPolicy and optimize the Service performance. Cilium watch NetworkPolicy and Service configuration and inject ebpf program into pod's IPvlan slave device.

Community

DingTalk

Join DingTalk group by DingTalkGroup id "35924643".

Security

Please report vulnerabilities by email to [email protected]. Also see our SECURITY.md file for details.

Name		Name	Last commit message	Last commit date
Latest commit History 1,267 Commits
.github		.github
charts		charts
cmd		cmd
daemon		daemon
deploy/images		deploy/images
deviceplugin		deviceplugin
docs		docs
examples/maxpods		examples/maxpods
hack		hack
monitoring		monitoring
pkg		pkg
plugin		plugin
policy		policy
rpc		rpc
terraform		terraform
tests		tests
types		types
.dockerignore		.dockerignore
.gitignore		.gitignore
.golangci.yml		.golangci.yml
LICENSE		LICENSE
Makefile		Makefile
README-zh_CN.md		README-zh_CN.md
README.md		README.md
SECURITY.md		SECURITY.md
eni.conf		eni.conf
go.mod		go.mod
go.sum		go.sum
terway-metric.yml		terway-metric.yml
terway-windows-eni.yml		terway-windows-eni.yml
terway-windows-eniip.yml		terway-windows-eniip.yml
terway-windows.yml		terway-windows.yml

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Repository files navigation

Terway CNI Network Plugin

Try It

Install Kubernetes

Install Terway network plugin

Terway network plugin usage

Vpc network container

Using ENI network interface to get the performance equivalent to the underlying network

ENI Secondary IP Pod

Using network policy to limit accessible between containers

Limit container in/out bandwidth

Build Terway

Test

Contribute

Built With

Community

DingTalk

Security

About

Releases 54

Packages

Contributors 34

Languages

License

AliyunContainerService/terway

Folders and files

Latest commit

History

Repository files navigation

Terway CNI Network Plugin

Try It

Install Kubernetes

Install Terway network plugin

Terway network plugin usage

Vpc network container

Using ENI network interface to get the performance equivalent to the underlying network

ENI Secondary IP Pod

Using network policy to limit accessible between containers

Limit container in/out bandwidth

Build Terway

Test

Contribute

Built With

Community

DingTalk

Security

About

Topics

Resources

License

Security policy

Stars

Watchers

Forks

Releases 54

Packages 0

Contributors 34

Languages

Packages