Please use the fork of kiwi-cam. This fork is inactive due to not using this plugin anymore.
This fork adds support for the TV type indroduced in iOS 12.2. I'm only give support for this specific accessory type!
This fork also contains updates the to Air Conditioner accessory, as detailed in the documenation below.
If you want to use this fork, use this command:
npm i -g homebridge-broadlink-rm-tv
There's been a lot of work done on the main fork to support some newer Broadlink devices. I (kiwi-cam) have had trouble getting this fork updated to include this support. As a temporary resolution I've created a new fork homebridge-broadlink-rm-pro which adds new Broadlink device support (Thanks to @Defensor7). The new fork can be installed using:
npm i -g homebridge-broadlink-rm-pro
Homebridge Broadlink RM [Original]
Welcome to the Broadlink RM Mini and Broadlink RM Pro plugin for Homebridge.
This plugin allows you to control your RM Mini and RM Pro with HomeKit using the Home app and Siri.
Full documentation can be found here. With the following additional configuration options available:
| key | description | example | default |
|---|---|---|---|
| pingGrace (optional) | Pauses ping status changes for the specified period (seconds) to allow device to start-up/shutdown after the change | 15 | 10 |
| key | description | example | default |
|---|---|---|---|
| w1DeviceID (optional) | Updates device current temperature from a Raspberry Pi Wire-1 thermometers (i.e. ds18b20). Value is the Device ID | 28-0321544e531ff |
The device can be setup to manage modes in one of two ways. If your AC unit accepts a hexcade to change mode only (without temperature details) you can set the mode keys (heat/cool) and then the temperatureX values to change the teperature. If your AC unit sends hexcodes that contain the mode AND temperature you can use the modeX codes alone.
When the mode is changed the mode hexcodes are sent first - if set. Then the modeX code is sent to set the temperature, if it is set. If a matching modeX code can't be found, the temperatureX code is sent. If neither of these temperature codes are found either defaultHeatTemperature or defaultCoolTemperature codes will be used depending on if the target Temperature is higher or lower than the current temperature.
| key | description |
|---|---|
| off | A hex code string to be sent when the air conditioner is asked to be turned off. |
| temperatureX | A hex code string where X is any temperature you wish to support e.g. "temperature30". |
| modeX | A hex code string where X is any temperture, and mode is one of "heat","cool", or "auto". Hex code used to set unit to the specified mode and temperature |
| key | description |
|---|---|
| data | Hex data stored as string. |
| pseudo-mode (optional) | The mode we set when this hex is sent. i.e. "heat" or "cool". For graphical purposes only (hence use of the term "pseudo"). Not recommended for ModeX key-values. |
| key | description | example | default |
|---|---|---|---|
| enableAutoOff | Turn the TV off automatically when onDuration has been reached. | true | false |
| onDuration | The amount of time before the TV automatically turns itself off (used in conjunction with enableAutoOff). | 5 | 60 |
| enableAutoOn | Turn the TV on automatically when offDuration has been reached | false | true |
| offDuration | The amount of time before the TV automatically turns itself on (used in conjunction with enableAutoOn). | 5 | 60 |
| pingIPAddress | When an IP address is provided, it is pinged every second. If a response is received then the TV turns on, otherwise it turns off. | "192.167.1.77" | |
| pingIPAddressStateOnly | Using this option will prevent the hex code from being sent when the state changes | true | false |
| pingFrequency | The frequency in seconds that the IP address should be pinged | 5 | 1 |
| pingGrace (optional) | Pauses ping status changes for the specified period (seconds) to allow device to start-up/shutdown after the change | 15 | 10 |
| data | see below |
| key | description |
|---|---|
| on | A hex code string to be sent when the tv is powered on. |
| off | A hex code string to be sent when the tv is powered off. |
| volume | see below |
| inputs | see below |
| remote | see below |
Configuration for volume changes via the Control Centre remote
| key | description |
|---|---|
| up | A hex code string to be sent to turn the TV volume up. |
| down | A hex code string to be sent to turn the TV volume down. |
Inputs contain an array of the below settings, one for each input
| key | description |
|---|---|
| name | The name used for the mode, shown in the GUI. |
| type | One of the follow to represent the mode: 'other','home_screen','tuner','hdmi','composite_video','s_video','component_video','dvi','airplay','usb','application' |
| data | A hex code string to be sent to switch the TV to the selected input. |
Configuration of button options in the Control Centre remote
| key | description |
|---|---|
| rewind | The hex code for this button function |
| fastForward | The hex code for this button function |
| nextTrack | The hex code for this button function |
| previousTrack | The hex code for this button function |
| arrowUp | The hex code for this button function |
| arrowDown | The hex code for this button function |
| arrowLeft | The hex code for this button function |
| arrowRight | The hex code for this button function |
| select | The hex code for this button function |
| back | The hex code for this button function |
| exit | The hex code for this button function |
| playPause | The hex code for this button function |
| info | The hex code for this button function |
Original: Thanks to @tattn (https://github.com/tattn/homebridge-rm-mini3), @PJCzx (https://github.com/PJCzx/homebridge-thermostat) @momodalo (https://github.com/momodalo/broadlinkjs) whose time and effort got me started.
In this fork: Thanks to @kiwi-cam (https://github.com/kiwi-cam) and @Cloudore (https://github.com/Cloudore) for your work!