diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 77a3e49abd325..112e87720dd92 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -1205,25 +1205,41 @@ #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. #define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present. - #define FIL_RUNOUT_PULL // Use internal pullup / pulldown for filament runout pins. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. // Override individually if the runout sensors vary //#define FIL_RUNOUT1_STATE LOW - //#define FIL_RUNOUT1_PULL + //#define FIL_RUNOUT1_PULLUP + //#define FIL_RUNOUT1_PULLDOWN + //#define FIL_RUNOUT2_STATE LOW - //#define FIL_RUNOUT2_PULL + //#define FIL_RUNOUT2_PULLUP + //#define FIL_RUNOUT2_PULLDOWN + //#define FIL_RUNOUT3_STATE LOW - //#define FIL_RUNOUT3_PULL + //#define FIL_RUNOUT3_PULLUP + //#define FIL_RUNOUT3_PULLDOWN + //#define FIL_RUNOUT4_STATE LOW - //#define FIL_RUNOUT4_PULL + //#define FIL_RUNOUT4_PULLUP + //#define FIL_RUNOUT4_PULLDOWN + //#define FIL_RUNOUT5_STATE LOW - //#define FIL_RUNOUT5_PULL + //#define FIL_RUNOUT5_PULLUP + //#define FIL_RUNOUT5_PULLDOWN + //#define FIL_RUNOUT6_STATE LOW - //#define FIL_RUNOUT6_PULL + //#define FIL_RUNOUT6_PULLUP + //#define FIL_RUNOUT6_PULLDOWN + //#define FIL_RUNOUT7_STATE LOW - //#define FIL_RUNOUT7_PULL + //#define FIL_RUNOUT7_PULLUP + //#define FIL_RUNOUT7_PULLDOWN + //#define FIL_RUNOUT8_STATE LOW - //#define FIL_RUNOUT8_PULL + //#define FIL_RUNOUT8_PULLUP + //#define FIL_RUNOUT8_PULLDOWN // Set one or more commands to execute on filament runout. // (After 'M412 H' Marlin will ask the host to handle the process.) diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 68d31ceaff9ff..baa0433f19b97 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -1217,7 +1217,8 @@ //#define POWER_LOSS_ZRAISE 2 // (mm) Z axis raise on resume (on power loss with UPS) //#define POWER_LOSS_PIN 44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module. //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss - //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate + //#define POWER_LOSS_PULLUP // Set pullup / pulldown as appropriate for your sensor + //#define POWER_LOSS_PULLDOWN //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/Marlin/src/feature/powerloss.h b/Marlin/src/feature/powerloss.h index 60923c6b3e9c6..73cd0b70faf40 100644 --- a/Marlin/src/feature/powerloss.h +++ b/Marlin/src/feature/powerloss.h @@ -120,12 +120,10 @@ class PrintJobRecovery { static inline void setup() { #if PIN_EXISTS(POWER_LOSS) - #if ENABLED(POWER_LOSS_PULL) - #if POWER_LOSS_STATE == LOW - SET_INPUT_PULLUP(POWER_LOSS_PIN); - #else - SET_INPUT_PULLDOWN(POWER_LOSS_PIN); - #endif + #if ENABLED(POWER_LOSS_PULLUP) + SET_INPUT_PULLUP(POWER_LOSS_PIN); + #elif ENABLED(POWER_LOSS_PULLDOWN) + SET_INPUT_PULLDOWN(POWER_LOSS_PIN); #else SET_INPUT(POWER_LOSS_PIN); #endif diff --git a/Marlin/src/feature/runout.h b/Marlin/src/feature/runout.h index e1b9ca11b74e4..09443e6e2b2d4 100644 --- a/Marlin/src/feature/runout.h +++ b/Marlin/src/feature/runout.h @@ -149,8 +149,8 @@ class FilamentSensorBase { public: static inline void setup() { - #define _INIT_RUNOUT_PIN(P,S,U) do{ if (DISABLED(U)) SET_INPUT(P); else if (S) SET_INPUT_PULLUP(P); else SET_INPUT_PULLDOWN(P); }while(0) - #define INIT_RUNOUT_PIN(N) _INIT_RUNOUT_PIN(FIL_RUNOUT##N##_PIN, FIL_RUNOUT##N##_STATE, FIL_RUNOUT##N##_PULL) + #define _INIT_RUNOUT_PIN(P,S,U,D) do{ if (ENABLED(U)) SET_INPUT_PULLUP(P); else if (ENABLED(D)) SET_INPUT_PULLDOWN(P); else SET_INPUT(P); }while(0) + #define INIT_RUNOUT_PIN(N) _INIT_RUNOUT_PIN(FIL_RUNOUT##N##_PIN, FIL_RUNOUT##N##_STATE, FIL_RUNOUT##N##_PULLUP, FIL_RUNOUT##N##_PULLDOWN) #if NUM_RUNOUT_SENSORS >= 1 INIT_RUNOUT_PIN(1); #endif diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h index 5fe73a9467ccb..42a4e037d8c3c 100644 --- a/Marlin/src/inc/Conditionals_LCD.h +++ b/Marlin/src/inc/Conditionals_LCD.h @@ -708,64 +708,88 @@ #ifndef FIL_RUNOUT1_STATE #define FIL_RUNOUT1_STATE FIL_RUNOUT_STATE #endif - #ifndef FIL_RUNOUT1_PULL - #define FIL_RUNOUT1_PULL FIL_RUNOUT_PULL + #ifndef FIL_RUNOUT1_PULLUP + #define FIL_RUNOUT1_PULLUP FIL_RUNOUT_PULLUP + #endif + #ifndef FIL_RUNOUT1_PULLDOWN + #define FIL_RUNOUT1_PULLDOWN FIL_RUNOUT_PULLDOWN #endif #endif #if NUM_RUNOUT_SENSORS >= 2 #ifndef FIL_RUNOUT2_STATE #define FIL_RUNOUT2_STATE FIL_RUNOUT_STATE #endif - #ifndef FIL_RUNOUT2_PULL - #define FIL_RUNOUT2_PULL FIL_RUNOUT_PULL + #ifndef FIL_RUNOUT2_PULLUP + #define FIL_RUNOUT2_PULLUP FIL_RUNOUT_PULLUP + #endif + #ifndef FIL_RUNOUT2_PULLDOWN + #define FIL_RUNOUT2_PULLDOWN FIL_RUNOUT_PULLDOWN #endif #endif #if NUM_RUNOUT_SENSORS >= 3 #ifndef FIL_RUNOUT3_STATE #define FIL_RUNOUT3_STATE FIL_RUNOUT_STATE #endif - #ifndef FIL_RUNOUT3_PULL - #define FIL_RUNOUT3_PULL FIL_RUNOUT_PULL + #ifndef FIL_RUNOUT3_PULLUP + #define FIL_RUNOUT3_PULLUP FIL_RUNOUT_PULLUP + #endif + #ifndef FIL_RUNOUT3_PULLDOWN + #define FIL_RUNOUT3_PULLDOWN FIL_RUNOUT_PULLDOWN #endif #endif #if NUM_RUNOUT_SENSORS >= 4 #ifndef FIL_RUNOUT4_STATE #define FIL_RUNOUT4_STATE FIL_RUNOUT_STATE #endif - #ifndef FIL_RUNOUT4_PULL - #define FIL_RUNOUT4_PULL FIL_RUNOUT_PULL + #ifndef FIL_RUNOUT4_PULLUP + #define FIL_RUNOUT4_PULLUP FIL_RUNOUT_PULLUP + #endif + #ifndef FIL_RUNOUT4_PULLDOWN + #define FIL_RUNOUT4_PULLDOWN FIL_RUNOUT_PULLDOWN #endif #endif #if NUM_RUNOUT_SENSORS >= 5 #ifndef FIL_RUNOUT5_STATE #define FIL_RUNOUT5_STATE FIL_RUNOUT_STATE #endif - #ifndef FIL_RUNOUT5_PULL - #define FIL_RUNOUT5_PULL FIL_RUNOUT_PULL + #ifndef FIL_RUNOUT5_PULLUP + #define FIL_RUNOUT5_PULLUP FIL_RUNOUT_PULLUP + #endif + #ifndef FIL_RUNOUT5_PULLDOWN + #define FIL_RUNOUT5_PULLDOWN FIL_RUNOUT_PULLDOWN #endif #endif #if NUM_RUNOUT_SENSORS >= 6 #ifndef FIL_RUNOUT6_STATE #define FIL_RUNOUT6_STATE FIL_RUNOUT_STATE #endif - #ifndef FIL_RUNOUT6_PULL - #define FIL_RUNOUT6_PULL FIL_RUNOUT_PULL + #ifndef FIL_RUNOUT6_PULLUP + #define FIL_RUNOUT6_PULLUP FIL_RUNOUT_PULLUP + #endif + #ifndef FIL_RUNOUT6_PULLDOWN + #define FIL_RUNOUT6_PULLDOWN FIL_RUNOUT_PULLDOWN #endif #endif #if NUM_RUNOUT_SENSORS >= 7 #ifndef FIL_RUNOUT7_STATE #define FIL_RUNOUT7_STATE FIL_RUNOUT_STATE #endif - #ifndef FIL_RUNOUT7_PULL - #define FIL_RUNOUT7_PULL FIL_RUNOUT_PULL + #ifndef FIL_RUNOUT7_PULLUP + #define FIL_RUNOUT7_PULLUP FIL_RUNOUT_PULLUP + #endif + #ifndef FIL_RUNOUT7_PULLDOWN + #define FIL_RUNOUT7_PULLDOWN FIL_RUNOUT_PULLDOWN #endif #endif #if NUM_RUNOUT_SENSORS >= 8 #ifndef FIL_RUNOUT8_STATE #define FIL_RUNOUT8_STATE FIL_RUNOUT_STATE #endif - #ifndef FIL_RUNOUT8_PULL - #define FIL_RUNOUT8_PULL FIL_RUNOUT_PULL + #ifndef FIL_RUNOUT8_PULLUP + #define FIL_RUNOUT8_PULLUP FIL_RUNOUT_PULLUP + #endif + #ifndef FIL_RUNOUT8_PULLDOWN + #define FIL_RUNOUT8_PULLDOWN FIL_RUNOUT_PULLDOWN #endif #endif #endif // FILAMENT_RUNOUT_SENSOR diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h index 4215f225e3eb6..072bb26bfe7aa 100644 --- a/Marlin/src/inc/SanityCheck.h +++ b/Marlin/src/inc/SanityCheck.h @@ -111,7 +111,7 @@ #elif defined(FILAMENT_SENSOR) #error "FILAMENT_SENSOR is now FILAMENT_WIDTH_SENSOR." #elif defined(ENDSTOPPULLUP_FIL_RUNOUT) - #error "ENDSTOPPULLUP_FIL_RUNOUT is now FIL_RUNOUT_PULL." + #error "ENDSTOPPULLUP_FIL_RUNOUT is now FIL_RUNOUT_PULLUP." #elif defined(DISABLE_MAX_ENDSTOPS) || defined(DISABLE_MIN_ENDSTOPS) #error "DISABLE_MAX_ENDSTOPS and DISABLE_MIN_ENDSTOPS deprecated. Use individual USE_*_PLUG options instead." #elif defined(LANGUAGE_INCLUDE) @@ -525,6 +525,8 @@ #error "EVENT_GCODE_SD_STOP is now EVENT_GCODE_SD_ABORT." #elif defined(GRAPHICAL_TFT_ROTATE_180) #error "GRAPHICAL_TFT_ROTATE_180 is now TFT_ROTATION set to TFT_ROTATE_180." +#elif defined(POWER_LOSS_PULL) + #error "POWER_LOSS_PULL is now specifically POWER_LOSS_PULL(UP|DOWN)." #elif defined(FIL_RUNOUT_INVERTING) #if FIL_RUNOUT_INVERTING #error "FIL_RUNOUT_INVERTING true is now FIL_RUNOUT_STATE HIGH." @@ -653,6 +655,8 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #if BOTH(ENDSTOPPULLUPS, ENDSTOPPULLDOWNS) #error "Enable only one of ENDSTOPPULLUPS or ENDSTOPPULLDOWNS." +#elif BOTH(FIL_RUNOUT_PULLUP, FIL_RUNOUT_PULLDOWN) + #error "Enable only one of FIL_RUNOUT_PULLUP or FIL_RUNOUT_PULLDOWN." #elif BOTH(ENDSTOPPULLUP_XMAX, ENDSTOPPULLDOWN_XMAX) #error "Enable only one of ENDSTOPPULLUP_X_MAX or ENDSTOPPULLDOWN_X_MAX." #elif BOTH(ENDSTOPPULLUP_YMAX, ENDSTOPPULLDOWN_YMAX) @@ -823,6 +827,22 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #error "FIL_RUNOUT7_PIN is required with NUM_RUNOUT_SENSORS >= 7." #elif NUM_RUNOUT_SENSORS >= 8 && !PIN_EXISTS(FIL_RUNOUT8) #error "FIL_RUNOUT8_PIN is required with NUM_RUNOUT_SENSORS >= 8." + #elif BOTH(FIL_RUNOUT1_PULLUP, FIL_RUNOUT1_PULLDOWN) + #error "You can't enable FIL_RUNOUT1_PULLUP and FIL_RUNOUT1_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT2_PULLUP, FIL_RUNOUT2_PULLDOWN) + #error "You can't enable FIL_RUNOUT2_PULLUP and FIL_RUNOUT2_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT3_PULLUP, FIL_RUNOUT3_PULLDOWN) + #error "You can't enable FIL_RUNOUT3_PULLUP and FIL_RUNOUT3_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT4_PULLUP, FIL_RUNOUT4_PULLDOWN) + #error "You can't enable FIL_RUNOUT4_PULLUP and FIL_RUNOUT4_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT5_PULLUP, FIL_RUNOUT5_PULLDOWN) + #error "You can't enable FIL_RUNOUT5_PULLUP and FIL_RUNOUT5_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT6_PULLUP, FIL_RUNOUT6_PULLDOWN) + #error "You can't enable FIL_RUNOUT6_PULLUP and FIL_RUNOUT6_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT7_PULLUP, FIL_RUNOUT7_PULLDOWN) + #error "You can't enable FIL_RUNOUT7_PULLUP and FIL_RUNOUT7_PULLDOWN at the same time." + #elif BOTH(FIL_RUNOUT8_PULLUP, FIL_RUNOUT8_PULLDOWN) + #error "You can't enable FIL_RUNOUT8_PULLUP and FIL_RUNOUT8_PULLDOWN at the same time." #elif FILAMENT_RUNOUT_DISTANCE_MM < 0 #error "FILAMENT_RUNOUT_DISTANCE_MM must be greater than or equal to zero." #elif DISABLED(ADVANCED_PAUSE_FEATURE) @@ -2824,6 +2844,10 @@ static_assert( _ARR_TEST(3,0) && _ARR_TEST(3,1) && _ARR_TEST(3,2) #error "BACKUP_POWER_SUPPLY requires a POWER_LOSS_PIN." #endif +#if BOTH(POWER_LOSS_PULLUP, POWER_LOSS_PULLDOWN) + #error "You can't enable POWER_LOSS_PULLUP and POWER_LOSS_PULLDOWN at the same time." +#endif + #if ENABLED(Z_STEPPER_AUTO_ALIGN) #if NUM_Z_STEPPER_DRIVERS <= 1 #error "Z_STEPPER_AUTO_ALIGN requires NUM_Z_STEPPER_DRIVERS greater than 1." diff --git a/Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp b/Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp index b6086b82ed4fb..226fb7291e280 100644 --- a/Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp +++ b/Marlin/src/lcd/extui/lib/anycubic_chiron/chiron_tft.cpp @@ -77,7 +77,7 @@ namespace Anycubic { // Filament runout is handled by Marlin settings in Configuration.h // opt_set FIL_RUNOUT_STATE HIGH // Pin state indicating that filament is NOT present. - // opt_enable FIL_RUNOUT_PULL + // opt_enable FIL_RUNOUT_PULLUP TFTSer.begin(115200); diff --git a/buildroot/tests/BIGTREE_GTR_V1_0-tests b/buildroot/tests/BIGTREE_GTR_V1_0-tests index 9750b8fc2c7a4..ef245143a8183 100644 --- a/buildroot/tests/BIGTREE_GTR_V1_0-tests +++ b/buildroot/tests/BIGTREE_GTR_V1_0-tests @@ -34,9 +34,9 @@ opt_set FIL_RUNOUT6_PIN 8 opt_set FIL_RUNOUT7_PIN 9 opt_set FIL_RUNOUT8_PIN 10 opt_set FIL_RUNOUT4_STATE HIGH -opt_enable FIL_RUNOUT4_PULL +opt_enable FIL_RUNOUT4_PULLUP opt_set FIL_RUNOUT8_STATE HIGH -opt_enable FIL_RUNOUT8_PULL +opt_enable FIL_RUNOUT8_PULLUP exec_test $1 $2 "BigTreeTech GTR 8 Extruders with Auto-Fan, Mixed TMC Drivers, and Runout Sensors with distinct states" "$3" restore_configs diff --git a/buildroot/tests/mega2560-tests b/buildroot/tests/mega2560-tests index 294de2a767d1d..01ade82891e1f 100755 --- a/buildroot/tests/mega2560-tests +++ b/buildroot/tests/mega2560-tests @@ -91,7 +91,7 @@ opt_enable ZONESTAR_LCD Z_PROBE_SERVO_NR Z_SERVO_ANGLES DEACTIVATE_SERVOS_AFTER_ AUTO_BED_LEVELING_3POINT DEBUG_LEVELING_FEATURE EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL \ NO_VOLUMETRICS EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES AUTOTEMP G38_PROBE_TARGET JOYSTICK \ DIRECT_STEPPING DETECT_BROKEN_ENDSTOP \ - FILAMENT_RUNOUT_SENSOR NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE Z_SAFE_HOMING FIL_RUNOUT3_PULL + FILAMENT_RUNOUT_SENSOR NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE Z_SAFE_HOMING FIL_RUNOUT3_PULLUP opt_set NUM_RUNOUT_SENSORS 5 opt_set FIL_RUNOUT2_PIN 44 opt_set FIL_RUNOUT3_PIN 45