-
Notifications
You must be signed in to change notification settings - Fork 293
Wiki Work
This page contains nots for things that should be done to clean up the wiki.
###Communicating with TinyG This whole area is a mess. We need a page with some backgorund, and a page on the proper use of Linemode transmission protocol.
- Tinyg-Communications-Programming Should be the start page. Other pages already link to this one.
Related pages that may useful data. Use these and get rid of stuff we don;t want:
- Flow-Control-and-Footers
- Sending-Data-to-TinyG-using-RX-Packet-Mode
- TinyG-Boot-Loader May be a child page of something else.
###Updating Firmware and Problems with Flashing These pages should be reviewed so they hold together under one "Updating Firmware" or "Flashing TinyG" page. These pages mostly hang together, bit not all are linked from the parent page. My suggestion would be to put a bulleted list of all pages at the top of the parent page. Here are the related pages that I found:
- TinyG-Updating-Firmware Parent page. Linked from sidebar
- TinyG-TG-Updater-App Child page
- SpDir-Continues-To-Flash-Error related page
- Firmware-Update-Verification-Failure related page
- Programming-TinyG-with-an-External-Programmer Outdated?
- Developer-Home-Page is blank. It either needs to be deleted or used for something
- TinyG-Developer-Notes
- Dual-Gantry-Configuration Superseded by the Shapeoko page
- Probing-Description-and-Operation is blank
- Data Sheets. Should have all the schematics and files. Do we want to go fully OSH on this now?
- TinyG-Shapeoko-Notes Has TGFX in it.
###Pages to Delete
- Data-Sheet---Version-8
- Initial-Setup
- Status-Reports
- TinyG-Networking
- TinyG-Configuration Not used anymore - goes direct to current version
- Tool-Chains-and-Project-Setup
- zzz%5BDEPRECATED%5DJSON-Flow-Control-Specification
- zzz(DEPRECATED)-5th-and-6th-Axis-Dual-Board-Operation
- zzz---BeagleBone-Black-AVR-Programmer
Move Elsewhere:
- TinyGv9k-Programming-and-Test-Instructions
- TinyGv9j-Manual-Programming-and-Test-Instructions
- TinyGv8g-Tester---BeagleBone-Black-Test-Rig-Setup
- TInyGv8g-BeagleBone-Black-Test-Rig-Operation
- TinyGv8-Production-Test-Instructions-for-Revision-2-Tester
- TinyGv8-Production-Test-Instructions-for-Revision-1-Tester
- TinyG-v7-data-sheet
Getting Started Pages
- Home
- What is TinyG?
- Getting Started
- Connecting TinyG
- Configuring TinyG
- Sending Gcode Files
- Flashing TinyG
- Chilipeppr
Reference Pages
- TinyG Help Page
- TinyG Tuning
- TinyG Command Line
- TinyG JSON
- Gcode Support
- Homing and Limits
- Inch and MM Units
- Alarms and Exceptions
- Coordinate Systems
- Status Codes
- Status Reports
- Power Management
- Feedhold and Resume
- Licensing
- TinyG v8 Data Sheet
Discussion Topics
- Test-Drive-TinyG
- Jerk Controlled Motion
- Gcode Parsing
- Shapeoko Setup
- OX CNC TinyG Guide
- Creating Gcode Files
- Milling With Noisy Spindles
- Stepper Motors and Power Supplies
- Text Wrappers and Transaction IDs
- Using External Drivers
- TinyG Projects
Chilipeppr
- Chilipeppr
- Chilipeppr Advanced Usage
- Chilipeppr Archive and Restore Parameters
- ChiliPeppr PCB Auto Level
- Automatic Z Homing When Milling PCBs
Troubleshooting
Developer Pages