⚡️ Apply PTC on all probing (MarlinFirmware#23764)

Co-authored-by: Scott Lahteine <[email protected]>

Marlin/src/feature/probe_temp_comp.cpp

@@ -28,6 +28,7 @@
 
 #include "probe_temp_comp.h"
 #include <math.h>
+#include "../module/temperature.h"
 
 ProbeTempComp ptc;
 
@@ -62,6 +63,7 @@ constexpr temp_calib_t ProbeTempComp::cali_info[TSI_COUNT];
 
 uint8_t ProbeTempComp::calib_idx; // = 0
 float ProbeTempComp::init_measurement; // = 0.0
+bool ProbeTempComp::enabled = true;
 
 void ProbeTempComp::reset() {
   TERN_(PTC_PROBE, LOOP_L_N(i, PTC_PROBE_COUNT) z_offsets_probe[i] = z_offsets_probe_default[i]);
@@ -169,6 +171,13 @@ bool ProbeTempComp::finish_calibration(const TempSensorID tsi) {
   return true;
 }
 
+void ProbeTempComp::apply_compensation(float &meas_z) {
+  if (!enabled) return;
+  TERN_(PTC_BED,    compensate_measurement(TSI_BED,   thermalManager.degBed(),     meas_z));
+  TERN_(PTC_PROBE,  compensate_measurement(TSI_PROBE, thermalManager.degProbe(),   meas_z));
+  TERN_(PTC_HOTEND, compensate_measurement(TSI_EXT,   thermalManager.degHotend(0), meas_z));
+}
+
 void ProbeTempComp::compensate_measurement(const TempSensorID tsi, const celsius_t temp, float &meas_z) {
   const uint8_t measurements = cali_info[tsi].measurements;
   const celsius_t start_temp = cali_info[tsi].start_temp,

Marlin/src/feature/probe_temp_comp.h

@@ -77,7 +77,6 @@ class ProbeTempComp {
     static void reset_index() { calib_idx = 0; };
     static uint8_t get_index() { return calib_idx; }
     static void reset();
-    static void clear_offsets(const TempSensorID tsi);
     static void clear_all_offsets() {
       TERN_(PTC_PROBE, clear_offsets(TSI_PROBE));
       TERN_(PTC_BED, clear_offsets(TSI_BED));
@@ -88,10 +87,16 @@ class ProbeTempComp {
     static void prepare_new_calibration(const_float_t init_meas_z);
     static void push_back_new_measurement(const TempSensorID tsi, const_float_t meas_z);
     static bool finish_calibration(const TempSensorID tsi);
-    static void compensate_measurement(const TempSensorID tsi, const celsius_t temp, float &meas_z);
+    static void set_enabled(const bool ena) { enabled = ena; }
+
+    // Apply all temperature compensation adjustments
+    static void apply_compensation(float &meas_z);
 
   private:
     static uint8_t calib_idx;
+    static bool enabled;
+
+    static void clear_offsets(const TempSensorID tsi);
 
     /**
      * Base value. Temperature compensation values will be deltas
@@ -104,6 +109,8 @@ class ProbeTempComp {
      * to allow generating values of higher temperatures.
      */
     static bool linear_regression(const TempSensorID tsi, float &k, float &d);
+
+    static void compensate_measurement(const TempSensorID tsi, const celsius_t temp, float &meas_z);
 };
 
 extern ProbeTempComp ptc;

Marlin/src/gcode/bedlevel/abl/G29.cpp

@@ -36,11 +36,6 @@
 #include "../../../module/probe.h"
 #include "../../queue.h"
 
-#if HAS_PTC
-  #include "../../../feature/probe_temp_comp.h"
-  #include "../../../module/temperature.h"
-#endif
-
 #if HAS_STATUS_MESSAGE
   #include "../../../lcd/marlinui.h"
 #endif
@@ -658,10 +653,6 @@ G29_TYPE GcodeSuite::G29() {
             break; // Breaks out of both loops
           }
 
-          TERN_(PTC_BED,    ptc.compensate_measurement(TSI_BED,   thermalManager.degBed(),     abl.measured_z));
-          TERN_(PTC_PROBE,  ptc.compensate_measurement(TSI_PROBE, thermalManager.degProbe(),   abl.measured_z));
-          TERN_(PTC_HOTEND, ptc.compensate_measurement(TSI_EXT,   thermalManager.degHotend(0), abl.measured_z));
-
           #if ENABLED(AUTO_BED_LEVELING_LINEAR)
 
             abl.mean += abl.measured_z;

Marlin/src/gcode/calibrate/G76_M871.cpp

@@ -109,7 +109,9 @@ static void say_failed_to_calibrate()       { SERIAL_ECHOPGM("!Failed to calibra
 
     auto g76_probe = [](const TempSensorID sid, celsius_t &targ, const xy_pos_t &nozpos) {
       do_z_clearance(5.0); // Raise nozzle before probing
+      ptc.set_enabled(false);
       const float measured_z = probe.probe_at_point(nozpos, PROBE_PT_STOW, 0, false);  // verbose=0, probe_relative=false
+      ptc.set_enabled(true);
       if (isnan(measured_z))
         SERIAL_ECHOLNPGM("!Received NAN. Aborting.");
       else {

Marlin/src/gcode/calibrate/M48.cpp

@@ -35,18 +35,23 @@
   #include "../../module/planner.h"
 #endif
 
+#if HAS_PTC
+  #include "../../feature/probe_temp_comp.h"
+#endif
+
 /**
  * M48: Z probe repeatability measurement function.
  *
  * Usage:
- *   M48 <P#> <X#> <Y#> <V#> <E> <L#> <S>
+ *   M48 <P#> <X#> <Y#> <V#> <E> <L#> <S> <C#>
  *     P = Number of sampled points (4-50, default 10)
  *     X = Sample X position
  *     Y = Sample Y position
  *     V = Verbose level (0-4, default=1)
  *     E = Engage Z probe for each reading
  *     L = Number of legs of movement before probe
  *     S = Schizoid (Or Star if you prefer)
+ *     C = Enable probe temperature compensation (0 or 1, default 1)
  *
  * This function requires the machine to be homed before invocation.
  */
@@ -107,6 +112,8 @@ void GcodeSuite::M48() {
     set_bed_leveling_enabled(false);
   #endif
 
+  TERN_(HAS_PTC, ptc.set_enabled(!parser.seen('C') || parser.value_bool()));
+
   // Work with reasonable feedrates
   remember_feedrate_scaling_off();
 
@@ -269,6 +276,9 @@ void GcodeSuite::M48() {
   // Re-enable bed level correction if it had been on
   TERN_(HAS_LEVELING, set_bed_leveling_enabled(was_enabled));
 
+  // Re-enable probe temperature correction
+  TERN_(HAS_PTC, ptc.set_enabled(true));
+
   report_current_position();
 }
 

Marlin/src/gcode/probe/G30.cpp

@@ -29,6 +29,10 @@
 #include "../../module/probe.h"
 #include "../../feature/bedlevel/bedlevel.h"
 
+#if HAS_PTC
+  #include "../../feature/probe_temp_comp.h"
+#endif
+
 /**
  * G30: Do a single Z probe at the current XY
  *
@@ -37,6 +41,7 @@
  *   X   Probe X position (default current X)
  *   Y   Probe Y position (default current Y)
  *   E   Engage the probe for each probe (default 1)
+ *   C   Enable probe temperature compensation (0 or 1, default 1)
  */
 void GcodeSuite::G30() {
 
@@ -51,7 +56,10 @@ void GcodeSuite::G30() {
   remember_feedrate_scaling_off();
 
   const ProbePtRaise raise_after = parser.boolval('E', true) ? PROBE_PT_STOW : PROBE_PT_NONE;
+
+  TERN_(HAS_PTC, ptc.set_enabled(!parser.seen('C') || parser.value_bool()));
   const float measured_z = probe.probe_at_point(pos, raise_after, 1);
+  TERN_(HAS_PTC, ptc.set_enabled(true));
   if (!isnan(measured_z))
     SERIAL_ECHOLNPGM("Bed X: ", pos.x, " Y: ", pos.y, " Z: ", measured_z);
 

Marlin/src/lcd/menu/menu_probe_offset.cpp

@@ -62,7 +62,7 @@ void probe_offset_wizard_menu() {
   if (LCD_HEIGHT >= 4)
     STATIC_ITEM(MSG_MOVE_NOZZLE_TO_BED, SS_CENTER|SS_INVERT);
 
-  STATIC_ITEM_P(PSTR("Z="), SS_CENTER, ftostr42_52(current_position.z));
+  STATIC_ITEM_P(PSTR("Z"), SS_CENTER, ftostr42_52(current_position.z));
   STATIC_ITEM(MSG_ZPROBE_ZOFFSET, SS_LEFT, ftostr42_52(calculated_z_offset));
 
   SUBMENU(MSG_MOVE_1MM,  []{ _goto_manual_move_z( 1);    });

Marlin/src/module/probe.cpp

@@ -77,6 +77,10 @@
   #include "servo.h"
 #endif
 
+#if HAS_PTC
+  #include "../feature/probe_temp_comp.h"
+#endif
+
 #if ENABLED(EXTENSIBLE_UI)
   #include "../lcd/extui/ui_api.h"
 #elif ENABLED(DWIN_CREALITY_LCD_ENHANCED)
@@ -801,7 +805,10 @@ float Probe::probe_at_point(const_float_t rx, const_float_t ry, const ProbePtRai
   do_blocking_move_to(npos, feedRate_t(XY_PROBE_FEEDRATE_MM_S));
 
   float measured_z = NAN;
-  if (!deploy()) measured_z = run_z_probe(sanity_check) + offset.z;
+  if (!deploy()) {
+    measured_z = run_z_probe(sanity_check) + offset.z;
+    TERN_(HAS_PTC, ptc.apply_compensation(measured_z));
+  }
   if (!isnan(measured_z)) {
     const bool big_raise = raise_after == PROBE_PT_BIG_RAISE;
     if (big_raise || raise_after == PROBE_PT_RAISE)