Reporting power consumption from a EHVH11SU26CB6W unit

[joncage]

I'm trying to get some instantaneous feedback on power consumption from my Diakin Altherme EHVH11SU26CB6W unit but not of the current or phases seem to be coming out with anything.

I'm using Altherma(LT_CB_11-16kW Bizone).h and have successfully retrieved the tank temperature but a lot of the rest looks less clear as to where it fits into the picture.

In these three values I was expecting to see some outputs giving me voltage and current but they're always zero:

INV primary current (A)
0
INV secondary current (A)
0
Voltage (N-phase) (V)
0

Have I misconfigured something here?

This is with just about everything turned on in my configuration header and the heating active:

Sensor Data Qty
10
INV compressor Qty
1
STD compressor Qty
0
Fan Data Qty
2
Expansion Valve Data Qty
2
4 Way Valve Data Qty
1
Crank Case Heater Qty
1
Solenoid valve Qty
2
Max. connectable indoor units
4
Connected Indoor Unit Qty
1
O/U MPU ID (xx)
71
O/U MPU ID (yy)
2
O/U capacity (kW)
11.2
NextDataGrid
Conv 995 not avail.
In-Out separator
Conv 998 not avail.
Operation Mode
Fan Only
Thermostat ON/OFF
ON
Restart standby
OFF
Startup Control
OFF
Defrost Operation
OFF
Oil Return Operation
OFF
Pressure equalizing operation
OFF
Demand Signal
OFF
Low noise control
OFF
Error type
Normal
Error Code
0
Target Evap. Temp.
---
Target Cond. Temp.
56.99
Discharge Temp. Drop
OFF
Discharge Temp. Protection Retry Qty
Conv 310 not avail.
Comp. INV Current Drop
OFF
Comp. INV Current Protection Retry Qty
Conv 311 not avail.
HP Drop Control
OFF
HP Protection Retry Qty
Conv 310 not avail.
LP Drop Control
OFF
LP Protection Retry Qty
Conv 311 not avail.
Fin Temp. Drop Control
OFF
Fin Temp. Protection Retry Qty
Conv 310 not avail.
Other Drop Control
OFF
R1T-Outdoor air temp.
15.1
O/U Heat Exch. Temp.
15.7
Discharge pipe temp.
22.8
Suction pipe temp.
22.9
Heat exchanger mid-temp.
15.1
Liquid pipe temp.(R6T)
18.9
Heat sink temp.
20.6
Pressure
11.8
Pressure(T)
13.88
INV primary current (A)
0
INV secondary current (A)
0
Voltage (N-phase) (V)
0
Brine Flow Switch
OFF
Brine inlet temp.
15.1
Brine outlet temp.
18.9
Refrig. temp. evap. In
15.7
Refrig. temp. evap.Out
22.9
INV frequency (rps)
0
INV frequency 2 (rps)
0
STD Compressor 1
OFF
STD Compressor 2
OFF
Fan 1 (step)
0
Fan 2 (step)
0
Expansion valve 1 (pls)
0
Expansion valve 2 (pls)
0
Expansion valve 3 (pls)
0
Expansion valve 4 (pls)
32,768
Expansion valve 5 (pls)
0
4 Way Valve 1
OFF
4 Way Valve 2
OFF
4 Way Valve 3
OFF
4 Way Valve 4
OFF
4 Way Valve 5
OFF
SV1 (hot gas)
OFF
SV2 (BPH)
OFF
Solenoid Valve 3
OFF
Solenoid Valve 4
OFF
Solenoid Valve 5
OFF
Freeze Protection
OFF
Silent Mode
OFF
Freeze Protection for water piping
OFF
Indoor Unit Code
Conv 314 not avail.
I/U capacity code
Conv 219 not avail.
DHW setpoint
48
LW setpoint (main)
41.4
Water flow switch
ON
Thermal Protector BUH
ON
Thermal protector BSH
ON
Benefit kWh rate power supply
OFF
Solar input
OFF
Bivalent Operation
OFF
2way valve(On:Heat Off:Cool)
OFF
3way valve(On:DHW Off:Space)
OFF
BSH
OFF
BUH Step1
OFF
BUH Step2
OFF
BPH
OFF
Water pump operation
ON
Solar pump operation
OFF
Leaving water temp. before BUH (R1T)
22.2
Leaving water temp. after BUH (R2T)
23.2
Refrig. Temp. liquid side (R3T)
27.7
Inlet water temp.(R4T)
22.1
DHW tank temp. (R5T)
42
Indoor ambient temp. (R1T)
26.1
Ext. indoor ambient sensor (R6T)
0
Reheat ON/OFF
ON
Storage ECO ON/OFF
OFF
Storage comfort ON/OFF
OFF
Powerful DHW Operation. ON/OFF
OFF
Space heating Operation ON/OFF
ON
System OFF (ON:System off)
OFF
Emergency (indoor) active/not active
OFF
LW setpoint (add)
37.3
RT setpoint
21
Add. Ext. RT Input Cool.
OFF
Add. Ext. RT Input Heat.
OFF
Main RT Cooling
OFF
Main RT Heating
ON
Pwr consumption limit 4
OFF
Pwr consumption limit 3
OFF
Pwr consumption limit 2
OFF
Pwr consumption limit 1
OFF
Tank preheat ON/OFF
OFF
Circulation pump operation
OFF
Alarm output
OFF
Space H Operation output
ON
Flow sensor (l/min)
19.6
Water pressure
0
Water pump signal (0:max-100:stop)
24
[Future] 3 way Valve Mixing 1
0
[Future] 3 way Valve Mixing 2
0
Hybrid Op. Mode
H/P only
Boiler Operation Demand
OFF
Boiler DHW Demand
OFF
Bypass Valve Output
ON
BE COP
0
Hybrid Heating Target Temp.
0
Boiler Heating Target Temp.
41.4
Add pump
OFF
Main pump
OFF
Mixed water temp.(R7T)
0
WifiRSSI
-58dBm
FreeMem
222372