-
Notifications
You must be signed in to change notification settings - Fork 28
/
T-Beam_v10.cfg
101 lines (79 loc) · 5.26 KB
/
T-Beam_v10.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
#define DEFAULT_AcftType 1 // [0..15] default aircraft-type: glider
#define DEFAULT_GeoidSepar 40 // [m]
#define DEFAULT_CONbaud 115200
#define DEFAULT_PPSdelay 100
#define DEFAULT_FreqPlan 0
#define DEFAULT_DispPage 3 // Fab501 Page to Display After Boot or Reset
#define WIFI_ADDRESS_IP1 192 // 192.168.1.1 for IP Address
#define WIFI_ADDRESS_IP2 168
#define WIFI_ADDRESS_IP3 1
#define WIFI_ADDRESS_IP4 1
#define WIFI_ADDRESS_GW1 0 // 0.0.0.0 for Gateway
#define WIFI_ADDRESS_GW2 0
#define WIFI_ADDRESS_GW3 0
#define WIFI_ADDRESS_GW4 0
#define WIFI_ADDRESS_MK1 255 // 255.255.255.0 for Mask
#define WIFI_ADDRESS_MK2 255
#define WIFI_ADDRESS_MK3 255
#define WIFI_ADDRESS_MK4 0
// #define WITH_HELTEC // HELTEC module: PCB LED on GPI025
// #define WITH_TTGO // TTGO module: PCB LED on GPIO2, GPIO25 free to use as DAC2 output
// #define WITH_TBEAM // T-Beam module
#define WITH_TBEAM_V10 // T-Beam module
// #define WITH_M5_JACEK // JACEK M5 ESP32 OGN-Tracker
// #define WITH_FollowMe // by Avionix
// #define WITH_ILI9341 // 320x240 M5stack
// #define WITH_ST7789 // IPS 240x240 ST7789
// #define WITH_TFT_LCD // TFT LCD (incomplete)
// #define WITH_OLED // OLED display on the I2C: some TTGO modules are without OLED display
// #define WITH_OLED2 // 2nd OLED display, I2C address next higher
// #define WITH_U8G2_OLED // I2C OLED through the U8g2 library
// #define WITH_U8G2_SH1106 // the bigger OLED controller
// #define WITH_U8G2_FLIP // flip the OLED screen
#define WITH_RFM95 // RF chip selection: both HELTEC and TTGO use sx1276 which is same as RFM95
// #define WITH_SX1262 // RF chip selection: both HELTEC and TTGO use sx1276 which is same as RFM95
// #define WITH_SLEEP // with software sleep mode controlled by the long-press on the button
#define WITH_AXP // with AXP192 power controller (T-BEAM V1.0)
// #define WITH_BQ // with BQ24295 power controller (FollowMe)
// #define WITH_LED_RX
// #define WITH_LED_TX
// #define WITH_GPS_ENABLE // use GPS_ENABLE control line to turn the GPS ON/OFF
#define WITH_GPS_PPS // use the PPS signal from GPS for precise time-sync.
#define WITH_GPS_CONFIG // attempt to configure higher GPS baud rate and airborne mode
#define WITH_GPS_UBX // GPS understands UBX
// #define WITH_GPS_MTK // GPS understands MTK
// #define WITH_GPS_SRF
// #define WITH_MAVLINK
// #define WITH_GPS_UBX_PASS // to pass directly UBX packets to/from GPS
// #define WITH_GPS_NMEA_PASS // to pass directly NMEA to/from GPS
// #define WITH_BMP180 // BMP180 pressure sensor
// #define WITH_BMP280 // BMP280 pressure sensor
#define WITH_BME280 // BMP280 with humidity (but still works with BMP280)
// #define WITH_MS5607 // MS5607 pressure sensor
#define WITH_PFLAA // PFLAU and PFLAA for compatibility with XCsoar and LK8000
// #define WITH_POGNT
#define WITH_LOOKOUT
#define WITH_CONFIG // interpret the console input: $POGNS to change parameters
// #define WITH_BEEPER // with digital buzzer
// #define WITH_SOUND // with analog sound produced by DAC on pin 25
// #define WITH_KNOB
// #define WITH_VARIO
// #define WITH_ADSL
// #define WITH_PAW
// #define WITH_FANET
#define WITH_LORAWAN
#define WITH_AP // WiFi Access Point: can work together with BT_SPP
#define WITH_AP_BUTTON // only starts when button pressed at sartup
#define WITH_BT_SPP // Bluetooth serial port for smartphone/tablet link: can work together with WiFi Access point
// #define WITH_STRATUX // beta-code: connect to Stratux WiFi and serve as GPS and OGN transmitter/receiver
// #define WITH_APRS // alpha-code: attempt to connect to the wifi router for uploading the log files to APRS
#define WITH_HTTP // HTTP server, works with AP dna should work with Stratux as well
#define WITH_SPIFFS // use SPIFFS file system in Flash
#define WITH_SPIFFS_FAT // use FAT on the SPIFFS
#define WITH_LOG // log own positions and other received to SPIFFS and possibly to uSD
// #define WITH_SD // use the SD card in SPI mode and FAT file system
// #define WITH_SDLOG // log console and IGC to the SD card
// #define WITH_ENCRYPT // Encrypt (optionally) the position
#if defined(WITH_STRATUX) || defined(WITH_APRS) || defined(WITH_AP)
#define WITH_WIFI
#endif