-
Notifications
You must be signed in to change notification settings - Fork 316
gallery
Today I received a blue and a white 128x64 OLED from HalTec
. The blue OLED has a SH1106 controller. It runs fine with the Uno (5V power) and the Due (3.3V power). U8glib constructor for the setup of the above picture:
U8GLIB_SH1106_128X64 u8g(4, 5, 6, 7); // SW SPI Com: SCK = 4, MOSI = 5, CS = 6, A0 = 7
The white 128x64 OLED has a SSD1306 controller. It did not run with the Arduno Uno, but it works fine with the Due (3.3V power supply):
U8GLIB_SSD1306_128X64 u8g(4, 5, 6, 7); // SW SPI Com: SCK = 4, MOSI = 5, CS = 6, A0 = 7
Unfortunately, I do not have the datasheet, so I can not say, whether it is a bug, that the SSD1306 OLED does not work with the Arduino Uno.
This is a very small OLED module based on the LD7032 controller (See here). It requires a 3.3 volt power supply, but the module has 5V tolerant inputs. Support for this controller is added in v1.16. Pin description for the PCB is here:
The SSD1306 has two different signal lines for the I2C data signal (one for input and one for output). However the pins of this OLED module are only connected to the input data line of the SSD1306. As a result it can not send the I2C ACK (it will be also invisible to any I2C scanner). This display from HelTec
is connected to 5V power supply. Data and clock lines accept 5V signals and do not need a pullup resistor. Support for this OLED is added to v1.16 of U8glib. A beta release can be downloaded here:
http://forum.arduino.cc/index.php?topic=219419.0
To support this display, the I2C constructor requires a special option:
U8GLIB_SSD1306_128X64 u8g(U8G_I2C_OPT_NO_ACK);
Dec 2013, I activated an inexpensive ($9) ST7920 based display module. Setup for this display is:
U8GLIB_ST7920_128X64_1X u8g(13, 11, 10, 9); // SPI Com: SCK = en = 13, MOSI = rw = 11, CS = di = 10, Reset = 9
There was almost no documentation, so I had to guess the backlight resistor. 150 Ohm seem to be ok with 5V.
I recently ordered a 240x64 COG Display with UC1608 controller from buy-display.com. Software modifications had been very simple for U8glib, but I had some trouble to get the bugs out of the hardware setup. Also, the extra reset line seems to be required in my case.
This is a 3.3V display, so for testing I decided to use an Arduino Due to avoid the additional level shifter. The backlight current is limited to 40mA (suggested value is 90mA).
Support for this display will be included in v1.15 of U8glib.
... an updated version of the Arduino community logo http://arduino.cc/en/Trademark/CommunityLogo for U8glib.
U8glib port to Cortex-M0: LPC1114 controller with SSD1351 OLED. ARM port will be available with U8glib v1.14.
Version v1.14 of U8lib will include support for a thermal printer. There is a 192x120 mode and 384x240 hi-resolution mode for the A2 Micro panel thermal printer. U8G_16BIT must be enabled for the hi-resolution mode (see u8g.h).
Version v1.13 of U8lib includes support for the SSD1351 OLED (ILSoft OLED and Arduino Shield). The picture shows the 128x128 OLED with the U8glib HiColor
(16 Bit) mode. The Arduino shield is put on top of an Arduino Uno.
This OLED will reach up to 4 frames per second with an ATMega (16MHz) and up to 26 frames per second with Arduino Due (ARM Core).
Note: The picture does not exactly reflects the colors from the display. For example pure red appears as orange on the image.
Thanks to the Arduino Community: V1.13 of u8glib will support HT1632 based LED matrix displays. See also http://forum.arduino.cc/index.php?topic=168537
These displays are used to test a new release of U8glib (Apr 2013). From top left to buttom right: KS0108 (128x64), T6963 (240x128, Varitronix), ST7565 (132x32, DOGM132, EA), ST7920 (192x32, NHD), UC1610 (160x104, DOGXL160, EA), SSD1325 (128x64, NHD), SSD1327 (96x96, Seeedstudio), ST7565 (128x64, DOGM128, EA), ST7565 (128x32, NHD), UC1701 (102x64, DOGS102, EA), PCF8812 (96x65, Nokia Display).
First time that I saw the U8glib logo on the Arduino Due (DOGS102 Display).
Recently, I got access to a used T6963 based display (Varitronix 240x128). There was not much documentation, so it took some time to implement support for it. LED backlight requires a lot of current (somewhere between 300mA and 500mA). Additional -15V are needed for the board, because it does not contain a negative DC-DC converter for the LCD. Support for this display will be available with U8glib v1.11.
With the help of the great breakout board from http://www.alexanderhiam.com/projects/nhd-bob/#1, I finally got my old NHD C12832 Display working with U8glib. Support for the NHD C12832 will be included in v1.10.
-
ChipKit
Uno32 - NHD 192x32 display with ST7920 controller
See also Flip-Disc Device
A picture from Frank's E-Bike controller project with the DOGXL160 display and U8glib. (Thanks to Frank for the picture).
- Seeedstudio 96x96 OLED
- ATMega328
- SSD1327 Controller
- I2C Interface
- ATMEGA328
- Aktive NHD 192x32 display with ST7920 controller
- EA DOGM132x32 not used here
- Picture from M2tklib project
- Arduino Board
- NHD OLED
- User input via serial interface