linux-3.10.patch

From: Stefan Wahren <stefan.wahren@i2se.com>
Subject: ethernet: qcaspi: Add config and build options

Add config and build options for the QCA7000 SPI protocol driver.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
---
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index ed956e0..6459d83 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -135,6 +135,7 @@ config ETHOC
 source "drivers/net/ethernet/packetengines/Kconfig"
 source "drivers/net/ethernet/pasemi/Kconfig"
 source "drivers/net/ethernet/qlogic/Kconfig"
+source "drivers/net/ethernet/qualcomm/Kconfig"
 source "drivers/net/ethernet/realtek/Kconfig"
 source "drivers/net/ethernet/renesas/Kconfig"
 source "drivers/net/ethernet/rdc/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 8268d85..f55ca92 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -53,6 +53,7 @@ obj-$(CONFIG_ETHOC) += ethoc.o
 obj-$(CONFIG_NET_PACKET_ENGINE) += packetengines/
 obj-$(CONFIG_NET_VENDOR_PASEMI) += pasemi/
 obj-$(CONFIG_NET_VENDOR_QLOGIC) += qlogic/
+obj-$(CONFIG_NET_VENDOR_QUALCOMM) += qualcomm/
 obj-$(CONFIG_NET_VENDOR_REALTEK) += realtek/
 obj-$(CONFIG_SH_ETH) += renesas/
 obj-$(CONFIG_NET_VENDOR_RDC) += rdc/
diff --git a/drivers/net/ethernet/qualcomm/Kconfig b/drivers/net/ethernet/qualcomm/Kconfig
new file mode 100644
index 0000000..f3a4714
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/Kconfig
@@ -0,0 +1,30 @@
+#
+# Qualcomm network device configuration
+#
+
+config NET_VENDOR_QUALCOMM
+	bool "Qualcomm devices"
+	default y
+	depends on SPI_MASTER && OF
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Qualcomm cards. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_QUALCOMM
+
+config QCA7000
+	tristate "Qualcomm Atheros QCA7000 support"
+	depends on SPI_MASTER && OF
+	---help---
+	  This SPI protocol driver supports the Qualcomm Atheros QCA7000.
+
+	  To compile this driver as a module, choose M here. The module
+	  will be called qcaspi.
+
+endif # NET_VENDOR_QUALCOMM
diff --git a/drivers/net/ethernet/qualcomm/Makefile b/drivers/net/ethernet/qualcomm/Makefile
new file mode 100644
index 0000000..9da2d75
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/Makefile
@@ -0,0 +1,6 @@
+#
+# Makefile for the Qualcomm network device drivers.
+#
+
+obj-$(CONFIG_QCA7000) += qcaspi.o
+qcaspi-objs := qca_spi.o qca_framing.o qca_7k.o qca_debug.o
-- 
1.7.9.5